* Rename ide_device_add() to ide_device_add_all() and make it accept
  'u8 idx[MAX_HWIFS]' instead of 'u8 idx[4]' as an argument.

* Add ide_device_add() wrapper for ide_device_add_all().

* Convert ide_generic_init() to use ide_device_add_all().

* Remove no longer needed ideprobe_init().

There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add hwif->chipset fixup identical to the one in ideprobe_init()
to ide_device_add().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

hwif->chipset should be set if the hwif is claimed by host driver.

Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

hwif->chipset should be set if the hwif is claimed by host driver.

Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

After hwif_register_devices() IDE devices are ready to be used so
the way in which ide_device_add() works currently is racy for hosts
with serialized / IRQ sharing interfaces.

Fix ide_device_add() by looping over interfaces for probe_hwif(),
hwif_init() and hwif_register_devices() operations.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Host drivers using ide_register_hw() and 'initializing == 1':

* ide-pnp
  - depends on ISA

* ide_arm 
  - ARM arch specific
  - initialized before all other host drivers

* ide-cris
  - CRIS arch specific => IDE_ARCH_OBSOLETE_INIT is not defined
  - broken

* ide-h8300
  - H8300 arch specific => IDE_ARCH_OBSOLETE_INIT is not defined, no PCI

* buddha/q40/gayle/macide/falconide
  - M68K arch specific => IDE_ARCH_OBSOLETE_INIT is not defined, no PCI

Since the only host drivers which probe interfaces before the above ones are:

* ali14xx/dtc2278/ht6560b/qd65xx/umc8672
  - depend on ISA
  - require IDE_ARCH_OBSOLETE_INIT=y to work

* PCI ones
  - depend on PCI

don't try to unregister interfaces if 'initializing == 1' in ide_register_hw()
(it is possible that built-in host drivers will claim all IDE interfaces but
later ide-pnp host driver will try to unregister them - this change fixes it).

Also skip hwif->hold check if 'initializing == 1' since it is set only by:

* pmac
  - PPC && PMAC specific => no ISA

* au1xxx-ide
  - MIPS && SOC_AU1200 specific => no ISA

and use ide_find_port() helper to find free ide_hwifs[] slot.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Assign drive->quirk_list in ->quirkproc implementations:
  - hpt366.c::hpt3xx_quirkproc()
  - pdc202xx_new.c::pdcnew_quirkproc()
  - pdc202xx_old.c::pdc202xx_quirkproc()

* Make ->quirkproc void.

* Move calling ->quirkproc from do_identify() to probe_hwif().

* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.

* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
  no longer needed drive->present check from is_dev_seagate_sata().

* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
  as an argument.  Then convert ide_register_hw() to accept 'quirkproc'
  argument instead of 'fixup' one.

* Remove no longer needed ->fixup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Dump taskfile HOB registers in ide_tf_load() (if DEBUG is defined).

* Remove no longer needed DEBUG code from __ide_do_rw_disk().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.

There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Enable/disable UDMA in atiixp_set_dma_mode().

* Remove no longer needed atiixp_dma_host_{on,off}() and save_mdma_mode[].

* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename cris_dma_{on,off}() to cris_dma_host_{on,off}().

* Remove no longer needed ->dma_off_quietly
  (IDE core has the needed code now).

* Make cris_dma_host_on() void.

I left fixing ide-cris after "kill dma_on/dma_off_quietly() methods"
patch because:

* Currently this driver is broken: cris_dma_on() (returns 'int')
  is assigned to hwif->dma_host_on (returns 'void') so the driver
  won't build.

* ->ide_dma_on method was missing so the driver OOPS-es on attempt
  to enable DMA.

* drive->using_dma was never set/cleared so DMA wouldn't be used anyway.

Unfortunately it seems that ide-cris stays broken even after this patch:

* V10: <asm/arch-v10/ide.h> needs fixing
  - ide_init_default_hwifs() should be removed
    (IDE core no longer uses it)
  - same for ide_init_hwif_ports() and ide_default_{irq,io_base}()
    (they shouldn't be needed for ide-cris host driver)

* V32: I'm unable to find a place which defines ETRAX_ARCH_V32

but I'm leaving fixing this to CRIS gurus. :)

Cc: Mikael Starvik <starvik@axis.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make ide_dma_off_quietly() and __ide_dma_on() always available.

* Drop "__" prefix from __ide_dma_on().

* Check for presence of ->dma_host_on instead of ->ide_dma_on.

* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
  to use ide_dma_on() and ide_dma_off_quietly() instead.

* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
  from ide_hwif_t.

* Make ide_dma_on() void.

There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().

Since there is no PCI device there should be no functionality
changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().

Since there is no PCI device there should be no functionality
changes caused by this patch.

Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().

Tested on Altix by Jeremy.
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix SWDMA/MWDMA masks in cy82c693_chipset.

* Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to
  check whether the DMA should be enabled even if ide_max_dma_mode()
  fails.

* Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode()
  and remove no longer needed cy82c693_ide_dma_on().  Then set
  IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in
  cy82c693_chipset.

* Bump driver version.

As a result of this patch cy82c693 driver will configure and use DMA on
all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Mask device DMA masks by ATA_{S,M}WDMA2 in cy82c693_ide_dma_on().

* Remove clipping of DMA modes by id->tDMA in cy82c693_dma_enable():
  - id->tDMA may not be defined on newer devices
  - id->vendor6/id->tDMA word is in LE endianness
    (cy82c693 seems to be Alpha specific though)

* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Set the correct hwif->dma_base for the second channel in
  ide_get_or_set_dma_base().

* Remove DMA enable code from cs5520_set_pio_mode(), this can
  be handled by the generic ->dma_host_on method now.

* Add VDMA check to ide_config_drive_speed().

* drive->using_dma was never enabled since cs5520 host driver's
  ->ide_dma_on method overrided the generic ->ide_dma_on (so
  __ide_dma_on() was never called, drive->using_dma was never set
  and VDMA was never used since it depends on drive->using_dma).

  Fix it by using ->dma_host_on method instead of ->ide_dma_on
  (also add matching ->dma_host_off method).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

IDE core guarantees that ->set_dma_mode will be called only
for DMA modes set in SWDMA/MWDMA/UDMA masks.

There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Program register 0x40 in sl82c105_resetproc().

* Remove no longer needed sl82c105_selectproc() and pci_set_drvdata() calls.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Program DMA timings in sl82c105_dma_start() (->dma_start method)
  before starting DMA transfer.

* Add sl82c105_dma_end() (->ide_dma_end method) to switch back to
  PIO timings when DMA transfer is complete.

* In sl82c105_set_pio_mode() program timings regardless of ->using_dma
  setting and in sl82c105_set_dma_mode() only cache the new timings.

* Remove no longer needed sl82c105_{ide_dma_on,off_quietly}().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
  [SCSI] usbstorage: use last_sector_bug flag universally
  [SCSI] libsas: abstract STP task status into a function
  [SCSI] ultrastor: clean up inline asm warnings
  [SCSI] aic7xxx: fix firmware build
  [SCSI] aacraid: fib context lock for management ioctls
  [SCSI] ch: remove forward declarations
  [SCSI] ch: fix device minor number management bug
  [SCSI] ch: handle class_device_create failure properly
  [SCSI] NCR5380: fix section mismatch
  [SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
  [SCSI] IB/iSER: add logical unit reset support
  [SCSI] don't use __GFP_DMA for sense buffers if not required
  [SCSI] use dynamically allocated sense buffer
  [SCSI] scsi.h: add macro for enclosure bit of inquiry data
  [SCSI] sd: add fix for devices with last sector access problems
  [SCSI] fix pcmcia compile problem
  [SCSI] aacraid: add Voodoo Lite class of cards.
  [SCSI] aacraid: add new driver features flags
  [SCSI] qla2xxx: Update version number to 8.02.00-k7.
  [SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] hifn795x: Disallow built-in hifn795x when HW_RANDOM is m

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (31 commits)
  ocfs2: clean up bh null checks
  ocfs2: document access rules for blocked_lock_list
  configfs: file.c fix possible recursive locking
  configfs: dir.c fix possible recursive locking
  configfs: Remove EXPERIMENTAL
  ocfs2: bump version number
  ocfs2/dlm: Clear joining_node on hearbeat node down
  ocfs2: convert byte order of constant instead of variable
  ocfs2: Update default cluster timeouts
  ocfs2: printf fixes
  ocfs2: Use generic_file_llseek
  ocfs2: Safer read_inline_data()
  ocfs2: Silence false lockdep warnings
  [PATCH 2/2] ocfs2: cluster aware flock()
  [PATCH 1/2] ocfs2: add flock lock type
  ocfs2: Local alloc window size changeable via mount option
  ocfs2: Support commit= mount option
  ocfs2: Add missing permission checks
  [PATCH 2/2] ocfs2: Implement group add for online resize
  [PATCH 1/2] ocfs2: Add group extend for online resize
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (67 commits)
  fix drivers/ata/sata_fsl.c double-decl
  [libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
  pata_legacy: Merge winbond support
  ata_generic: Cenatek support
  pata_winbond: error return
  pata_serverworks: Fix cable types and cosmetics
  pata_mpc52xx: remove un-needed assignment
  libata: fix off-by-one in error categorization
  ahci: factor out AHCI enabling and enable AHCI before reading CAP
  ata_piix: implement SIDPR SCR access
  ata_piix: convert to prepare - activate initialization
  libata: factor out ata_pci_activate_sff_host() from ata_pci_one()
  [libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
  pata_legacy: resychronize with upstream changes and resubmit
  [libata] pata_legacy: typo fix
  [libata] pata_winbond: update for new ->data_xfer hook
  pata_pcmcia: convert to new data_xfer prototype
  libata annotations and fixes
  libata: use dev_driver_string() instead of "libata" in libata-sff.c
  ata_piix: kill unused constants and flags
  ...

If we know a buffer_head is non-null, then brelse() is unnecessary and
put_bh() can be used instead. Also, an explicit check for NULL is
unnecessary when using brelse(). This patch only covers buffer_head_io.c and
resize.c, which have recently added code which exhibits this problem.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

ocfs2_super->blocked_lock_list and ocfs2_super->blocked_lock_count have some
usage restrictions which aren't immediately obvious to anyone reading the
code. It's a good idea to document this so that we avoid making costly
mistakes in the future.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

configfs_register_subsystem() with default_groups triggers recursive locking.
it seems that mutex_lock_nested is needed.

=============================================
[ INFO: possible recursive locking detected ]
2.6.24-rc6 #145
---------------------------------------------
swapper/1 is trying to acquire lock:
 (&sb->s_type->i_mutex_key#3){--..}, at: [<c40c9a9e>] configfs_add_file+0x2e/0x70

but task is already holding lock:
 (&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca985>] configfs_register_subsystem+0x55/0x130

other info that might help us debug this:
1 lock held by swapper/1:
 #0:  (&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca985>] configfs_register_subsystem+0x55/0x130

stack backtrace:
Pid: 1, comm: swapper Not tainted 2.6.24-rc6 #145
 [<c40053ba>] show_trace_log_lvl+0x1a/0x30
 [<c4005e82>] show_trace+0x12/0x20
 [<c400687e>] dump_stack+0x6e/0x80
 [<c404ec72>] __lock_acquire+0xe62/0x1120
 [<c404efb2>] lock_acquire+0x82/0xa0
 [<c43fda88>] mutex_lock_nested+0x98/0x2e0
 [<c40c9a9e>] configfs_add_file+0x2e/0x70
 [<c40c9b0c>] configfs_create_file+0x2c/0x40
 [<c40ca639>] configfs_attach_item+0x139/0x220
 [<c40ca734>] configfs_attach_group+0x14/0x140
 [<c40ca7e9>] configfs_attach_group+0xc9/0x140
 [<c40ca9f6>] configfs_register_subsystem+0xc6/0x130
 [<c45c8186>] init_netconsole+0x2b6/0x300
 [<c45a75f2>] kernel_init+0x142/0x320
 [<c4004fb3>] kernel_thread_helper+0x7/0x14
 =======================
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

configfs_register_subsystem() with default_groups triggers recursive locking.
it seems that mutex_lock_nested is needed.

=============================================
[ INFO: possible recursive locking detected ]
2.6.24-rc6 #141
---------------------------------------------
swapper/1 is trying to acquire lock:
 (&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca76f>] configfs_attach_group+0x4f/0x190

but task is already holding lock:
 (&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca9d5>] configfs_register_subsystem+0x55/0x130

other info that might help us debug this:
1 lock held by swapper/1:
 #0:  (&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca9d5>] configfs_register_subsystem+0x55/0x130

stack backtrace:
Pid: 1, comm: swapper Not tainted 2.6.24-rc6 #141
 [<c40053ba>] show_trace_log_lvl+0x1a/0x30
 [<c4005e82>] show_trace+0x12/0x20
 [<c400687e>] dump_stack+0x6e/0x80
 [<c404ec72>] __lock_acquire+0xe62/0x1120
 [<c404efb2>] lock_acquire+0x82/0xa0
 [<c43fdad8>] mutex_lock_nested+0x98/0x2e0
 [<c40ca76f>] configfs_attach_group+0x4f/0x190
 [<c40caa46>] configfs_register_subsystem+0xc6/0x130
 [<c45c8186>] init_netconsole+0x2b6/0x300
 [<c45a75f2>] kernel_init+0x142/0x320
 [<c4004fb3>] kernel_thread_helper+0x7/0x14
 =======================
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

configfs has been alive and kicking for a while now.  It underpins some
non-EXPERIMENTAL subsystems, such as OCFS2's cluster stack.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

Bump the printed version to 1.5.0. This helps us quickly identify which
version of Ocfs2 a bug filer is running.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

Currently the process of dlm join contains 2 steps: query join and assert join.
After query join, the joined node will set its joining_node. So if the joining
node happens to panic before the 2nd step, the joined node will fail to clear
its joining_node flag because that node isn't in the domain map. It at least
cause 2 problems.
1. All the new join request will fail. So no new node can mount the volume.
2. The joined node can't umount the volume since during the umount process it
   has to wait for the joining_node to be unknown. So the umount will be hanged.

The solution is to clear the joining_node before we check the domain map.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

Convert byte order of constant instead of variable it will be done at
compile time vs run time. Remove unused le32_and_cpu.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

Lots of people are having trouble with the default timeouts, which are too
low. These new values are derived from an informal survey taken on
ocfs2-users, as well as data from bug reports. This should reduce the amount
of cluster disconnects and subsequent fencing seen during normal workloads.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

Explicitely convert loff_t to long long in printf. Just for sure...
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

We should use generic_file_llseek() and not default_llseek() so that
s_maxbytes gets properly checked when seeking.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>

In ocfs2_read_inline_data() we should store file size in loff_t. Although
the file size should fit in 32 bits we cannot be sure in case filesystem is
corrupted.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>