Having the SDMA driver use a tasklet for running the clients
callback introduce some issues:
  - probability to have desynchronized data because of the
    race condition created since the DMA transaction status
    is retrieved only when the callback is executed, leaving
    plenty of time for transaction status to get altered.
  - inter-transfer latency which can leave channels idle.

Move the callback execution, for cyclic channels, to SDMA
interrupt (as advised in `Documentation/dmaengine/provider.txt`)
to (a)reduce the inter-transfer latency and (b) eliminate the
race condition possibility where DMA transaction status might
be changed by the time is read.

The responsibility of the SDMA interrupt latency
is moved to the SDMA clients which case by case should defer
the work to bottom-halves when needed.
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

DMA on Intel Quark SoC is a part of UART IP block. Enable it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Quark SoC supports MSI for LPSS, in particular for UART. Enable MSI for
Intel Quark.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Quark has DesignWare UART. Move the code from 8250_pci to 8250_lpss.
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The SoCs, such as Intel Braswell, have DesignWare UART IP. Split out the
support of such chips to a separate module which also will be used for Intel
Quark later.

The rationale to have the separate driver to be existing:
- Do not contaminate 8250_pci.c anymore with LPSS related quirks
- All of them are using same DMA engine and they are Designware IP which means
  that in the future we might share the code between 8250_dw.c and 8250_lpss.c
- It reduces the kernel memory footprint on non-X86 machines where 8250_pci.c
  is in use

Besides the split the driver also has been refactored, in particular a) the DMA
and port setup are separate functions, b) the two new structures lpss8250 and
lpss8250_board are introduced to keep necessary data instead of
pciserial_board, c) DMA parameters are passed to the DMA setup via mentioned
custom structure. Most of the changes are done due to the future support of
UART DMA on Intel Quark.

The Intel Quark UART DMA support is based on bits taking from BSP code
published by Intel earlier.

The driver does not use any specific power management. PCI core takes care of
the default behaviour during suspend and resume.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Quark has 16550A compatible UART with autoflow feature enabled. It has
only 16 bytes of FIFO. Currently serial8250_do_set_termios() prevents to enable
autoflow since the minimum requirement of 32 bytes of FIFO size.

Drop a FIFO size limitation to allow autoflow control be enabled on such UARTs.

While here, comment out UART_CAP_AFE for PORT_AR7 since it wasn't working and
it will be not a good idea to use it in conjunction with trigger level of 1
byte.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some UARTs, e.g. one is used in Intel Quark, have a different address base for
DMA operations. Introduce an additional field (per RX and TX DMA channels) in
struct uart_8250_dma to cover those cases.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some users consider DMA optional, thus when driver is not compiled we shouldn't
prevent compilation of the users. Add stubs for dw_dma_probe() and
dw_dma_remove().
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There are at least two known devices, e.g. DMA controller found on ARC AXS101
SDP board, that have LLP register and no multi block transfer support at the
same time.

Override autodetection by user provided data.
Reported-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Quark UART uses DesignWare DMA IP. Though the DMA IP is connected in such
way that handshake interface uses inverted polarity. We have to provide a
possibility to set this in the DMA driver when configuring a channel.

Introduce a new member of custom slave configuration called 'hs_polarity' and
set active low polarity in case this value is 'true'.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It seems we need to extend custom slave configuration by one more member to
support Intel Quart UART. It becomes a burden to manage all members of struct
dw_dma_slave one-by-one.

Replace the set of fields by embedding struct dw_dma_slave into struct
dw_dma_chan.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

  Previously sc16is7xx_power was called in order to set the device to a
  low power mode.

  However since SC16IS7XX_EFR_ENABLE_BIT was not set beforehand this
  suspend request had not effect.

  Also, soft-reset the device prior to port initialization. It may
  otherwise be in a state (interrupt pending, fifo not empty) which
  prevents it from sleeping.
Signed-off-by: Florian Vallee <fvallee@eukrea.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mediatek can support baud rate up to 4M.
the 'uart_get_baud_rate' function will limit the max baud rate.
Modify max baud to remove the limit.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use of_property_read_bool to check for the existence of a property.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
-       if (of_get_property(e1,e2,NULL))
+       if (of_property_read_bool(e1,e2))
        S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable Vybrid's build-in support for RS-485 auto RTS for controlling line
direction of RS-485 transceiver driver.

Enable RS485 feature by either using ioctrl 'TIOCSRS485' or enable it in the
device tree by setting 'linux,rs485-enabled-at-boot-time' property.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When DMA mode is enabled one need to make sure the DMA channels are idle before
entering suspend mode especially when UART ports which are set as wakeup source
and console port with no_console_suspend is set. This patch takes care of
gracefully releasing DMA channels for the above two cases and start the DMA at
resume.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Drop PIO to DMA switching and use scatter/gather DMA for Tx path to improve
performance.

Some part of the code is borrowed from imx serial driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The initial approach of DMA implementatin for RX is inefficient due to switching
from PIO to DMA, this leads to overruns especially on instances with the smaller
FIFO. To address these issues this patch uses a cyclic DMA for receiver path.

Some part of the code is borrowed from atmel serial driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

By default the driver always configure the mode as 8s1 even when 8m1 mode is
selected. Fix this by adding support to control the space/mark bit.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 8e4934c6 ("tty: serial: fsl_lpuart: clear receive flag on FIFO
flush") implemented clearing of the receive flag by reading the status register
only. It turned out that even though we flush the FIFO afterwards, a explicit
read of the data register is still required.

This leads to a FIFO underrun. To avoid this, follow the advice in the overrun
"Operation section": Unconditionally clear RXUF after using RXFLUSH.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add suspend/resume support.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the tx_empty callback only considers the Transmit Complete Flag (TC).
The reference manual is not quite clear if the TC flag covers the TX FIFO too.
Debug prints on real hardware have shown that from time to time the TC flag is
asserted (indicating Transmitter idle) while there are still data in the
TX FIFO. Hence, in this case the serial core will call the shutdown callback
even though there are data remaining in the TX FIFO buffers.

Avoid early shutdowns by considering the TX FIFO empty flag too. Also avoid
theoretical race conditions between DMA and the driver by checking whether the
TX DMA is in progress too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It should check the data->pclk, not data->clk when get apb_pclk.

Fixes: c8ed99d4("serial: 8250_dw: Add support for deferred probing")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 2nd parameter of 'find_first_zero_bit' is the number of bits to search.
In this case, we are passing 'sizeof(vt8500_ports_in_use)'.
'vt8500_ports_in_use' is an 'unsigned long'. So the sizeof is likely to
return 4 on a 32 bits kernel.

A few lines below, we check if it is below VT8500_MAX_PORTS, which is 6.

It is likely that the number of bits in a long was expected here.

In order to fix it:
   - use DECLARE_BITMAP when declaring the vt8500_ports_in_use
   - use VT8500_MAX_PORTS as a maximum value when checking/setting bits in
     this bitmap
   - modify code now that 'vt8500_ports_in_use' has become a pointer
     because of the use of DECLARE_BITMAP

It has been spotted by the following coccinelle script:
@@
expression ret, x;

@@
*  ret = \(find_first_bit \| find_first_zero_bit\) (x, sizeof(...));
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty_port_close handles much of the common parts of tty close. Convert
uart_close to use it and move the serial_core specific parts into
tty_port.shutdown function. This will be needed to use tty_port functions
directly from in kernel clients.

This change causes ops->stop_rx() to be called after uart_wait_until_sent()
is called which I think should be fine. Otherwise, the sequence of the
close should be the same.

Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty_port_open handles much of the common parts of tty opening. Convert
uart_open to use it and move the serial_core specific parts into
tty_port.activate function. This will be needed to use tty_port functions
directly from in kernel clients.

The tricky part is uart_port_startup can return positive values to allow
setserial to configure the port. We now return the positive value to
tty_port_open so that the tty is not marked as initialized and then set the
return value in uart_open to 0.

Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Samsung serial driver registered for CPU frequency transitions to
recalculate its clock when ARM clock frequency changes.  This is needed
only on S3C24xx platform so limit the ifdef to respective cpufreq
driver.

On S3C24xx the ratio ratio between frequencies of UART's parent clock
(pclk) and ARM's parent clock (fclk) remains fixed.  Therefore when ARM
clock frequency goes down, the serial is also affected.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The USART device provides a fractional baud rate generator to get a more
accurate baud rate. It can be used only when the USART is configured in
'normal mode' and this feature is not available on AT91RM9200 SoC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no Peripheral Identification Registers on ZTE PL011 device, so
although the driver amba-pl011 is ready to work for ZTE device, the
device cannot be probed by the driver at all.

With arm,primecell-periphid DT bindings (bindings/arm/primecell.txt) in
place, it should be the cleanest the way to use a pseudo-ID to probe the
device from AMBA bus.  We create an unofficial vendor number
AMBA_VENDOR_LINUX, which will practically never become an official
vendor ID, and takes Configuration, Revision number, and Part number as
input to compose a pseudo-ID for ZTE device.

Also, since we start using vendor_zte to probe ZTE device, the
__maybe_unused for vendor_zte is removed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ZTE PL011 device has a fixed FIFO size 16.  Let's add a .get_fifosize
hook for it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For some reason we do not really understand, ZTE hardware designers
choose to define PL011 Flag Register bit positions differently from
standard ones as below.

	Bit		Standard	ZTE
	-----------------------------------
	CTS		0		1
	DSR		1		3
	BUSY		3		8
	RI		8		0

Let's define these bits into vendor data and get ZTE PL011 supported
properly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull thermal updates from Zhang Rui:

 - Fix a race condition when updating cooling device, which may lead to
   a situation where a thermal governor never updates the cooling
   device.  From Michele Di Giorgio.

 - Fix a zero division error when disabling the forced idle injection
   from the intel powerclamp.  From Petr Mladek.

 - Add suspend/resume callback for intel_pch_thermal thermal driver.
   From Srinivas Pandruvada.

 - Another two fixes for clocking cooling driver and hwmon sysfs I/F.
   From Michele Di Giorgio and Kuninori Morimoto.

[ Hmm.  That suspend/resume callback for intel_pch_thermal doesn't look
  like a fix, but I'm letting it slide..  - Linus ]

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: clock_cooling: Fix missing mutex_init()
  thermal: hwmon: EXPORT_SYMBOL_GPL for thermal hwmon sysfs
  thermal: fix race condition when updating cooling device
  thermal/powerclamp: Prevent division by zero when counting interval
  thermal: intel_pch_thermal: Add suspend/resume callback

Pull m68knommu fix from Greg Ungerer:
 "This contains only a single fix for a register corruption problem on
  certain types of m68k flat format binaries"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: fix user a5 register being overwritten

Merge tag 'fixes-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull h8300 and unicore32 architecture fixes from Guenter Roeck:
 "Two patches to fix h8300 and unicore32 builds.

  unicore32 builds have been broken since v4.6.  The fix has been
  available in -next since March of this year.

  h8300 builds have been broken since the last commit window.  The fix
  has been available in -next since June of this year"

* tag 'fixes-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  h8300: Add missing include file to asm/io.h
  unicore32: mm: Add missing parameter to arch_vma_access_permitted

Pull arm64 fixes from Catalin Marinas:

 - support for nr_cpus= command line argument (maxcpus was previously
   changed to allow secondary CPUs to be hot-plugged)

 - ARM PMU interrupt handling fix

 - fix potential TLB conflict in the hibernate code

 - improved handling of EL1 instruction aborts (better error reporting)

 - removal of useless jprobes code for stack saving/restoring

 - defconfig updates

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: defconfig: enable CONFIG_LOCALVERSION_AUTO
  arm64: defconfig: add options for virtualization and containers
  arm64: hibernate: handle allocation failures
  arm64: hibernate: avoid potential TLB conflict
  arm64: Handle el1 synchronous instruction aborts cleanly
  arm64: Remove stack duplicating code from jprobes
  drivers/perf: arm-pmu: Fix handling of SPI lacking "interrupt-affinity" property
  drivers/perf: arm-pmu: convert arm_pmu_mutex to spinlock
  arm64: Support hard limit of cpu count by nr_cpus

Pull KVM fixes from Radim Krčmář:
 "KVM:
   - lock kvm_device list to prevent corruption on device creation.

  PPC:
   - split debugfs initialization from creation of the xics device to
     unlock the newly taken kvm lock earlier.

  s390:
   - prevent userspace from triggering two WARN_ON_ONCE.

  MIPS:
   - fix several issues in the management of TLB faults (Cc: stable)"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  MIPS: KVM: Propagate kseg0/mapped tlb fault errors
  MIPS: KVM: Fix gfn range check in kseg0 tlb faults
  MIPS: KVM: Add missing gfn range check
  MIPS: KVM: Fix mapped fault broken commpage handling
  KVM: Protect device ops->create and list_add with kvm->lock
  KVM: PPC: Move xics_debugfs_init out of create
  KVM: s390: reset KVM_REQ_MMU_RELOAD if mapping the prefix failed
  KVM: s390: set the prefix initially properly

Pull block fixes from Jens Axboe:

 - an NVMe fix from Gabriel, fixing a suspend/resume issue on some
   setups

 - addition of a few missing entries in the block queue sysfs
   documentation, from Joe

 - a fix for a sparse shadow warning for the bvec iterator, from
   Johannes

 - a writeback deadlock involving raid issuing barriers, and not
   flushing the plug when we wakeup the flusher threads.  From
   Konstantin

 - a set of patches for the NVMe target/loop/rdma code, from Roland and
   Sagi

* 'for-linus' of git://git.kernel.dk/linux-block:
  bvec: avoid variable shadowing warning
  doc: update block/queue-sysfs.txt entries
  nvme: Suspend all queues before deletion
  mm, writeback: flush plugged IO in wakeup_flusher_threads()
  nvme-rdma: Remove unused includes
  nvme-rdma: start async event handler after reconnecting to a controller
  nvmet: Fix controller serial number inconsistency
  nvmet-rdma: Don't use the inline buffer in order to avoid allocation for small reads
  nvmet-rdma: Correctly handle RDMA device hot removal
  nvme-rdma: Make sure to shutdown the controller if we can
  nvme-loop: Remove duplicate call to nvme_remove_namespaces
  nvme-rdma: Free the I/O tags when we delete the controller
  nvme-rdma: Remove duplicate call to nvme_remove_namespaces
  nvme-rdma: Fix device removal handling
  nvme-rdma: Queue ns scanning after a sucessful reconnection
  nvme-rdma: Don't leak uninitialized memory in connect request private data

h8300 builds fail with

arch/h8300/include/asm/io.h:9:15: error: unknown type name ‘u8’
arch/h8300/include/asm/io.h:15:15: error: unknown type name ‘u16’
arch/h8300/include/asm/io.h:21:15: error: unknown type name ‘u32’

and many related errors.

Fixes: 23c82d41bdf4 ("kexec-allow-architectures-to-override-boot-mapping-fix")
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>