- 18 Jul, 2017 40 commits
-
-
Josh Poimboeuf authored
commit 34a477e5 upstream. On x86-32, with CONFIG_FIRMWARE and multiple CPUs, if you enable function graph tracing and then suspend to RAM, it will triple fault and reboot when it resumes. The first fault happens when booting a secondary CPU: startup_32_smp() load_ucode_ap() prepare_ftrace_return() ftrace_graph_is_dead() (accesses 'kill_ftrace_graph') The early head_32.S code calls into load_ucode_ap(), which has an an ftrace hook, so it calls prepare_ftrace_return(), which calls ftrace_graph_is_dead(), which tries to access the global 'kill_ftrace_graph' variable with a virtual address, causing a fault because the CPU is still in real mode. The fix is to add a check in prepare_ftrace_return() to make sure it's running in protected mode before continuing. The check makes sure the stack pointer is a virtual kernel address. It's a bit of a hack, but it's not very intrusive and it works well enough. For reference, here are a few other (more difficult) ways this could have potentially been fixed: - Move startup_32_smp()'s call to load_ucode_ap() down to *after* paging is enabled. (No idea what that would break.) - Track down load_ucode_ap()'s entire callee tree and mark all the functions 'notrace'. (Probably not realistic.) - Pause graph tracing in ftrace_suspend_notifier_call() or bringup_cpu() or __cpu_up(), and ensure that the pause facility can be queried from real mode. Reported-by:
Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Tested-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: "Rafael J . Wysocki" <rjw@rjwysocki.net> Cc: linux-acpi@vger.kernel.org Cc: Borislav Petkov <bp@alien8.de> Cc: Len Brown <lenb@kernel.org> Link: http://lkml.kernel.org/r/5c1272269a580660703ed2eccf44308e790c7a98.1492123841.git.jpoimboe@redhat.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> [bwh: Backported to 3.2: adjust context] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Ben Hutchings authored
commit 4cca0457 upstream. The switch that conditionally sets CPUPOWER_CAP_HAS_TURBO_RATIO and CPUPOWER_CAP_IS_SNB flags is missing a break, so all cores get both flags set and an assumed base clock of 100 MHz for turbo values. Reported-by:
GSR <gsr.bugs@infernal-iceberg.com> Tested-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-
Takashi Iwai authored
commit 4e7655fd upstream. The snd_use_lock_sync() (thus its implementation snd_use_lock_sync_helper()) has the 5 seconds timeout to break out of the sync loop. It was introduced from the beginning, just to be "safer", in terms of avoiding the stupid bugs. However, as Ben Hutchings suggested, this timeout rather introduces a potential leak or use-after-free that was apparently fixed by the commit 2d7d5400 ("ALSA: seq: Fix race during FIFO resize"): for example, snd_seq_fifo_event_in() -> snd_seq_event_dup() -> copy_from_user() could block for a long time, and snd_use_lock_sync() goes timeout and still leaves the cell at releasing the pool. For fixing such a problem, we remove the break by the timeout while still keeping the warning. Suggested-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
Takashi Iwai <tiwai@suse.de> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
James Hogan authored
commit 162b270c upstream. KGDB is a kernel debug stub and it can't be used to debug userland as it can only safely access kernel memory. On MIPS however KGDB has always got the register state of sleeping processes from the userland register context at the beginning of the kernel stack. This is meaningless for kernel threads (which never enter userland), and for user threads it prevents the user seeing what it is doing while in the kernel: (gdb) info threads Id Target Id Frame ... 3 Thread 2 (kthreadd) 0x0000000000000000 in ?? () 2 Thread 1 (init) 0x000000007705c4b4 in ?? () 1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201 Get the register state instead from the (partial) kernel register context stored in the task's thread_struct for resume() to restore. All threads now correctly appear to be in context_switch(): (gdb) info threads Id Target Id Frame ... 3 Thread 2 (kthreadd) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903 2 Thread 1 (init) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903 1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201 Call clobbered registers which aren't saved and exception registers (BadVAddr & Cause) which can't be easily determined without stack unwinding are reported as 0. The PC is taken from the return address, such that the state presented matches that found immediately after returning from resume(). Fixes: 88547001 ("[MIPS] kgdb: add arch support for the kernel's kgdb core") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15829/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Thomas Gleixner authored
commit 6fdc6dd9 upstream. The vsyscall32 sysctl can racy against a concurrent fork when it switches from disabled to enabled: arch_setup_additional_pages() if (vdso32_enabled) --> No mapping sysctl.vsysscall32() --> vdso32_enabled = true create_elf_tables() ARCH_DLINFO_IA32 if (vdso32_enabled) { --> Add VDSO entry with NULL pointer Make ARCH_DLINFO_IA32 check whether the VDSO mapping has been set up for the newly forked process or not. Signed-off-by:
Andy Lutomirski <luto@amacapital.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mathias Krause <minipli@googlemail.com> Link: http://lkml.kernel.org/r/20170410151723.602367196@linutronix.deSigned-off-by:
-
Guillaume Nault authored
commit 321a52a3 upstream. pppol2tp_getsockopt() doesn't take into account the error code returned by pppol2tp_tunnel_getsockopt() or pppol2tp_session_getsockopt(). If error occurs there, pppol2tp_getsockopt() continues unconditionally and reports erroneous values. Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Guillaume Nault authored
commit 364700cf upstream. pppol2tp_setsockopt() unconditionally overwrites the error value returned by pppol2tp_tunnel_setsockopt() or pppol2tp_session_setsockopt(), thus hiding errors from userspace. Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by:
-
bsegall@google.com authored
commit 5402e97a upstream. In PT_SEIZED + LISTEN mode STOP/CONT signals cause a wakeup against __TASK_TRACED. If this races with the ptrace_unfreeze_traced at the end of a PTRACE_LISTEN, this can wake the task /after/ the check against __TASK_TRACED, but before the reset of state to TASK_TRACED. This causes it to instead clobber TASK_WAKING, allowing a subsequent wakeup against TRACED while the task is still on the rq wake_list, corrupting it. Oleg said: "The kernel can crash or this can lead to other hard-to-debug problems. In short, "task->state = TASK_TRACED" in ptrace_unfreeze_traced() assumes that nobody else can wake it up, but PTRACE_LISTEN breaks the contract. Obviusly it is very wrong to manipulate task->state if this task is already running, or WAKING, or it sleeps again" [akpm@linux-foundation.org: coding-style fixes] Fixes: 9899d11f ("ptrace: ensure arch_ptrace/ptrace_request can never race with SIGKILL") Link: http://lkml.kernel.org/r/xm26y3vfhmkp.fsf_-_@bsegall-linux.mtv.corp.google.comSigned-off-by:
Ben Segall <bsegall@google.com> Acked-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Martin K. Petersen authored
commit 7c856152 upstream. We previously made sure that the reported disk capacity was less than 0xffffffff blocks when the kernel was not compiled with large sector_t support (CONFIG_LBDAF). However, this check assumed that the capacity was reported in units of 512 bytes. Add a sanity check function to ensure that we only enable disks if the entire reported capacity can be expressed in terms of sector_t. Reported-by:
Steve Magnani <steve.magnani@digidescorp.com> Cc: Bart Van Assche <Bart.VanAssche@sandisk.com> Reviewed-by:
Bart Van Assche <Bart.VanAssche@sandisk.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> [bwh: Backported to 3.2: use integer literal instead of U32_MAX] Signed-off-by:
-
Martin K. Petersen authored
commit a00a7862 upstream. Kefeng Wang discovered that old versions of the QEMU CD driver would return mangled mode data causing us to walk off the end of the buffer in an attempt to parse it. Sanity check the returned mode sense data. Reported-by:
Kefeng Wang <wangkefeng.wang@huawei.com> Tested-by:
-
Juergen Gross authored
commit 9121b15b upstream. Connecting to the backend isn't working reliably in xen-fbfront: in case XenbusStateInitWait of the backend has been missed the backend transition to XenbusStateConnected will trigger the connected state only without doing the actions required when the backend has connected. Signed-off-by:
Juergen Gross <jgross@suse.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Guillaume Nault authored
commit e08293a4 upstream. Take a reference on the sessions returned by l2tp_session_find_nth() (and rename it l2tp_session_get_nth() to reflect this change), so that caller is assured that the session isn't going to disappear while processing it. For procfs and debugfs handlers, the session is held in the .start() callback and dropped in .show(). Given that pppol2tp_seq_session_show() dereferences the associated PPPoL2TP socket and that l2tp_dfs_seq_session_show() might call pppol2tp_show(), we also need to call the session's .ref() callback to prevent the socket from going away from under us. Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Fixes: 0ad66140 ("l2tp: Add debugfs files for dumping l2tp debug info") Fixes: 309795f4 ("l2tp: Add netlink control API for L2TP") Signed-off-by:
-
Paul Mackerras authored
commit 48fe9e94 upstream. In the past, there was only one load-with-reservation instruction, lwarx, and if a program attempted a lwarx on a misaligned address, it would take an alignment interrupt and the kernel handler would emulate it as though it was lwzx, which was not really correct, but benign since it is loading the right amount of data, and the lwarx should be paired with a stwcx. to the same address, which would also cause an alignment interrupt which would result in a SIGBUS being delivered to the process. We now have 5 different sizes of load-with-reservation instruction. Of those, lharx and ldarx cause an immediate SIGBUS by luck since their entries in aligninfo[] overlap instructions which were not fixed up, but lqarx overlaps with lhz and will be emulated as such. lbarx can never generate an alignment interrupt since it only operates on 1 byte. To straighten this out and fix the lqarx case, this adds code to detect the l[hwdq]arx instructions and return without fixing them up, resulting in a SIGBUS being delivered to the process. Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> [bwh: Backported to 3.2: open-code get_xop()] Signed-off-by:
-
Yuejie Shi authored
commit 89e357d8 upstream. A dump may come in the middle of another dump, modifying its dump structure members. This race condition will result in NULL pointer dereference in kernel. So add a lock to prevent that race. Fixes: 83321d6b ("[AF_KEY]: Dump SA/SP entries non-atomically") Signed-off-by:
Yuejie Shi <syjcnss@gmail.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> [bwh: Backported to 3.2: - pfkey_dump() doesn't support filters - Adjust context] Signed-off-by:
-
Nicholas Bellinger authored
commit 1c99de98 upstream. Once upon a time back in 2009, a work-around was added to support the GlobalSAN iSCSI initiator v3.3 for MacOSX, which during login did not propose nor respond to MaxBurstLength, FirstBurstLength, DefaultTime2Wait and DefaultTime2Retain keys. The work-around in iscsi_check_proposer_for_optional_reply() allowed the missing keys to be proposed, but did not require waiting for a response before moving to full feature phase operation. This allowed GlobalSAN v3.3 to work out-of-the box, and for many years we didn't run into login interopt issues with any other initiators.. Until recently, when Martin tried a QLogic 57840S iSCSI Offload HBA on Windows 2016 which completed login, but subsequently failed with: Got unknown iSCSI OpCode: 0x43 The issue was QLogic MSFT side did not propose DefaultTime2Wait + DefaultTime2Retain, so LIO proposes them itself, and immediately transitions to full feature phase because of the GlobalSAN hack. However, the QLogic MSFT side still attempts to respond to DefaultTime2Retain + DefaultTime2Wait, even though LIO has set ISCSI_FLAG_LOGIN_NEXT_STAGE3 + ISCSI_FLAG_LOGIN_TRANSIT in last login response. So while the QLogic MSFT side should have been proposing these two keys to start, it was doing the correct thing per RFC-3720 attempting to respond to proposed keys before transitioning to full feature phase. All that said, recent versions of GlobalSAN iSCSI (v5.3.0.541) does correctly propose the four keys during login, making the original work-around moot. So in order to allow QLogic MSFT to run unmodified as-is, go ahead and drop this long standing work-around. Reported-by:
Martin Svec <martin.svec@zoner.cz> Cc: Martin Svec <martin.svec@zoner.cz> Cc: Himanshu Madhani <Himanshu.Madhani@cavium.com> Cc: Arun Easi <arun.easi@cavium.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Guillaume Nault authored
commit 2777e2ab upstream. Callers of l2tp_nl_session_find() need to hold a reference on the returned session since there's no guarantee that it isn't going to disappear from under them. Relying on the fact that no l2tp netlink message may be processed concurrently isn't enough: sessions can be deleted by other means (e.g. by closing the PPPOL2TP socket of a ppp pseudowire). l2tp_nl_cmd_session_delete() is a bit special: it runs a callback function that may require a previous call to session->ref(). In particular, for ppp pseudowires, the callback is l2tp_session_delete(), which then calls pppol2tp_session_close() and dereferences the PPPOL2TP socket. The socket might already be gone at the moment l2tp_session_delete() calls session->ref(), so we need to take a reference during the session lookup. So we need to pass the do_ref variable down to l2tp_session_get() and l2tp_session_get_by_ifname(). Since all callers have to be updated, l2tp_session_find_by_ifname() and l2tp_nl_session_find() are renamed to reflect their new behaviour. Fixes: 309795f4 ("l2tp: Add netlink control API for L2TP") Signed-off-by:
-
Guillaume Nault authored
commit dbdbc73b upstream. l2tp_session_create() relies on its caller for checking for duplicate sessions. This is racy since a session can be concurrently inserted after the caller's verification. Fix this by letting l2tp_session_create() verify sessions uniqueness upon insertion. Callers need to be adapted to check for l2tp_session_create()'s return code instead of calling l2tp_session_find(). pppol2tp_connect() is a bit special because it has to work on existing sessions (if they're not connected) or to create a new session if none is found. When acting on a preexisting session, a reference must be held or it could go away on us. So we have to use l2tp_session_get() instead of l2tp_session_find() and drop the reference before exiting. Fixes: d9e31d17 ("l2tp: Add L2TP ethernet pseudowire support") Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by:
-
Guillaume Nault authored
commit 57377d63 upstream. Holding a reference on session is required before calling pppol2tp_session_ioctl(). The session could get freed while processing the ioctl otherwise. Since pppol2tp_session_ioctl() uses the session's socket, we also need to take a reference on it in l2tp_session_get(). Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by:
-
Guillaume Nault authored
commit 61b9a047 upstream. Taking a reference on sessions in l2tp_recv_common() is racy; this has to be done by the callers. To this end, a new function is required (l2tp_session_get()) to atomically lookup a session and take a reference on it. Callers then have to manually drop this reference. Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by:
-
Uwe Kleine-König authored
commit a6040bc6 upstream. The reference manual for the i.MX28 recommends to calculate the divisor as divisor = (UARTCLK * 32) / baud rate, rounded to the nearest integer , so let's do this. For a typical setup of UARTCLK = 24 MHz and baud rate = 115200 this changes the divisor from 6666 to 6667 and so the actual baud rate improves from 115211.521 Bd (error ≅ 0.01 %) to 115194.240 Bd (error ≅ 0.005 %). Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust context, indentation] Signed-off-by:
-
Stefan Wahren authored
commit df57cf6a upstream. Currently mxs-auart doesn't care correctly about the baud rate divisor. According to reference manual the baud rate divisor must be between 0x000000EC and 0x003FFFC0. So calculate the possible baud rate range and use it for uart_get_baud_rate(). Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Hans de Goede authored
commit 923713b3 upstream. SDIO cards may need clock to send the card interrupt to the host. On a cherrytrail tablet with a RTL8723BS wifi chip, without this patch pinging the tablet results in: PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data. 64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=78.6 ms 64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1760 ms 64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=753 ms 64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=3.88 ms 64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=795 ms 64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1841 ms 64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=810 ms 64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1860 ms 64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=812 ms 64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=48.6 ms Where as with this patch I get: PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data. 64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=3.96 ms 64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1.97 ms 64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=17.2 ms 64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=2.46 ms 64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=2.83 ms 64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1.40 ms 64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=2.10 ms 64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1.40 ms 64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=2.04 ms 64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=1.40 ms Cc: Dong Aisheng <b29396@freescale.com> Cc: Ian W MORRISON <ianwmorrison@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Acked-by:
Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Thomas Hellstrom authored
commit 53e16798 upstream. The mesa winsys sometimes uses unimplemented parameter requests to check for features. Remove the error message to avoid bloating the kernel log. Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by:
Brian Paul <brianp@vmware.com> Reviewed-by:
Sinclair Yeh <syeh@vmware.com> Signed-off-by:
-
Murray McAllister authored
commit 63774069 upstream. In vmw_get_cap_3d_ioctl(), a user can supply 0 for a size that is used in vzalloc(). This eventually calls dump_stack() (in warn_alloc()), which can leak useful addresses to dmesg. Add check to avoid a size of 0. Signed-off-by:
Murray McAllister <murray.mcallister@insomniasec.com> Reviewed-by:
-
Thomas Hellstrom authored
commit f7652afa upstream. A malicious caller could otherwise hand over handles to other objects causing all sorts of interesting problems. Testing done: Ran a Fedora 25 desktop using both Xorg and gnome-shell/Wayland. Signed-off-by:
-
Sebastian Siewior authored
commit 9cd9a21c upstream. In commit 6afaf8a4 ("UBI: flush wl before clearing update marker") I managed to trigger and fix a similar bug. Now here is another version of which I assumed it wouldn't matter back then but it turns out UBI has a check for it and will error out like this: |ubi0 warning: validate_vid_hdr: inconsistent used_ebs |ubi0 error: validate_vid_hdr: inconsistent VID header at PEB 592 All you need to trigger this is? "ubiupdatevol /dev/ubi0_0 file" + a powercut in the middle of the operation. ubi_start_update() sets the update-marker and puts all EBs on the erase list. After that userland can proceed to write new data while the old EB aren't erased completely. A powercut at this point is usually not that much of a tragedy. UBI won't give read access to the static volume because it has the update marker. It will most likely set the corrupted flag because it misses some EBs. So we are all good. Unless the size of the image that has been written differs from the old image in the magnitude of at least one EB. In that case UBI will find two different values for `used_ebs' and refuse to attach the image with the error message mentioned above. So in order not to get in the situation, the patch will ensure that we wait until everything is removed before it tries to write any data. The alternative would be to detect such a case and remove all EBs at the attached time after we processed the volume-table and see the update-marker set. The patch looks bigger and I doubt it is worth it since usually the write() will wait from time to time for a new EB since usually there not that many spare EB that can be used. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Richard Weinberger <richard@nod.at> [bwh: Backported to 3.2: ubi_wl_flush() only takes 1 parameter] Signed-off-by:
-
Mathias Nyman authored
commit d3519b9d upstream. xhci needs to take care of four scenarios when asked to cancel a URB. 1 URB is not queued or already given back. usb_hcd_check_unlink_urb() will return an error, we pass the error on 2 We fail to find xhci internal structures from urb private data such as virtual device and endpoint ring. Give back URB immediately, can't do anything about internal structures. 3 URB private data has valid pointers to xhci internal data, but host is not responding. give back URB immedately and remove the URB from the endpoint lists. 4 Everyting is working add URB to cancel list, queue a command to stop the endpoint, after which the URB can be turned to no-op or skipped, removed from lists, and given back. We failed to give back the urb in case 2 where the correct device and endpoint pointers could not be retrieved from URB private data. This caused a hang on Dell Inspiron 5558/0VNM2T at resume from suspend as urb was never returned. [ 245.270505] INFO: task rtsx_usb_ms_1:254 blocked for more than 120 seconds. [ 245.272244] Tainted: G W 4.11.0-rc3-ARCH #2 [ 245.273983] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 245.275737] rtsx_usb_ms_1 D 0 254 2 0x00000000 [ 245.277524] Call Trace: [ 245.279278] __schedule+0x2d3/0x8a0 [ 245.281077] schedule+0x3d/0x90 [ 245.281961] usb_kill_urb.part.3+0x6c/0xa0 [usbcore] [ 245.282861] ? wake_atomic_t_function+0x60/0x60 [ 245.283760] usb_kill_urb+0x21/0x30 [usbcore] [ 245.284649] usb_start_wait_urb+0xe5/0x170 [usbcore] [ 245.285541] ? try_to_del_timer_sync+0x53/0x80 [ 245.286434] usb_bulk_msg+0xbd/0x160 [usbcore] [ 245.287326] rtsx_usb_send_cmd+0x63/0x90 [rtsx_usb] Reported-by: diego.viola@gmail.com Tested-by: diego.viola@gmail.com Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Josh Poimboeuf authored
commit 61b79e16 upstream. Paul Menzel reported a warning: WARNING: CPU: 0 PID: 774 at /build/linux-ROBWaj/linux-4.9.13/kernel/trace/trace_functions_graph.c:233 ftrace_return_to_handler+0x1aa/0x1e0 Bad frame pointer: expected f6919d98, received f6919db0 from func acpi_pm_device_sleep_wake return to c43b6f9d The warning means that function graph tracing is broken for the acpi_pm_device_sleep_wake() function. That's because the ACPI Makefile unconditionally sets the '-Os' gcc flag to optimize for size. That's an issue because mcount-based function graph tracing is incompatible with '-Os' on x86, thanks to the following gcc bug: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=42109 I have another patch pending which will ensure that mcount-based function graph tracing is never used with CONFIG_CC_OPTIMIZE_FOR_SIZE on x86. But this patch is needed in addition to that one because the ACPI Makefile overrides that config option for no apparent reason. It has had this flag since the beginning of git history, and there's no related comment, so I don't know why it's there. As far as I can tell, there's no reason for it to be there. The appropriate behavior is for it to honor CONFIG_CC_OPTIMIZE_FOR_{SIZE,PERFORMANCE} like the rest of the kernel. Reported-by:
-
James Morse authored
commit 7d64f82c upstream. When removing a GHES device notified by SCI, list_del_rcu() is used, ghes_remove() should call synchronize_rcu() before it goes on to call kfree(ghes), otherwise concurrent RCU readers may still hold this list entry after it has been freed. Signed-off-by:
James Morse <james.morse@arm.com> Reviewed-by:
"Huang, Ying" <ying.huang@intel.com> Fixes: 81e88fdc (ACPI, APEI, Generic Hardware Error Source POLL/IRQ/NMI notification type support) Signed-off-by:
-
Arnd Bergmann authored
commit f0bb2d50 upstream. The latest gcc-7.0.1 snapshot reports a new warning: virtio/virtio_balloon.c: In function 'update_balloon_stats': virtio/virtio_balloon.c:258:26: error: 'events[2]' is used uninitialized in this function [-Werror=uninitialized] virtio/virtio_balloon.c:260:26: error: 'events[3]' is used uninitialized in this function [-Werror=uninitialized] virtio/virtio_balloon.c:261:56: error: 'events[18]' is used uninitialized in this function [-Werror=uninitialized] virtio/virtio_balloon.c:262:56: error: 'events[17]' is used uninitialized in this function [-Werror=uninitialized] This seems absolutely right, so we should add an extra check to prevent copying uninitialized stack data into the statistics. >From all I can tell, this has been broken since the statistics code was originally added in 2.6.34. Fixes: 9564e138 ("virtio: Add memory statistics reporting to the balloon driver (V4)") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Ladi Prosek <lprosek@redhat.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Ladi Prosek authored
commit fc865322 upstream. When init_vqs runs, virtio_balloon.stats is either uninitialized or contains stale values. The host updates its state with garbage data because it has no way of knowing that this is just a marker buffer used for signaling. This patch updates the stats before pushing the initial buffer. Alternative fixes: * Push an empty buffer in init_vqs. Not easily done with the current virtio implementation and violates the spec "Driver MUST supply the same subset of statistics in all buffers submitted to the statsq". * Push a buffer with invalid tags in init_vqs. Violates the same spec clause, plus "invalid tag" is not really defined. Note: the spec says: When using the legacy interface, the device SHOULD ignore all values in the first buffer in the statsq supplied by the driver after device initialization. Note: Historically, drivers supplied an uninitialized buffer in the first buffer. Unfortunately QEMU does not seem to implement the recommendation even for the legacy interface. Signed-off-by:
-
Gao Feng authored
commit 75c689dc upstream. In the commit 93557f53 ("netfilter: nf_conntrack: nf_conntrack snmp helper"), the snmp_helper is replaced by nf_nat_snmp_hook. So the snmp_helper is never registered. But it still tries to unregister the snmp_helper, it could cause the panic. Now remove the useless snmp_helper and the unregister call in the error handler. Fixes: 93557f53 ("netfilter: nf_conntrack: nf_conntrack snmp helper") Signed-off-by:
Gao Feng <fgao@ikuai8.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Arnd Bergmann authored
commit f6aafac1 upstream. aarch64-linux-gcc-7 complains about code it doesn't fully understand: drivers/infiniband/hw/qib/qib_iba7322.c: In function 'qib_7322_txchk_change': include/asm-generic/bitops/non-atomic.h:105:35: error: 'shadow' may be used uninitialized in this function [-Werror=maybe-uninitialized] The code is right, and despite trying hard, I could not come up with a version that I liked better than just adding a fake initialization here to shut up the warning. Fixes: f931551b ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters") Signed-off-by:
Ira Weiny <ira.weiny@intel.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Nathan Sullivan authored
commit 49d52e81 upstream. If the PHY is halted on stop, then do not set the state to PHY_UP. This ensures the phy will be restarted later in phy_start when the machine is started again. Fixes: 00db8189 ("This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details.") Signed-off-by:
Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by:
Brad Mouring <brad.mouring@ni.com> Acked-by:
Xander Huff <xander.huff@ni.com> Acked-by:
Kyle Roeschley <kyle.roeschley@ni.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Takashi Iwai authored
commit 2d7d5400 upstream. When a new event is queued while processing to resize the FIFO in snd_seq_fifo_clear(), it may lead to a use-after-free, as the old pool that is being queued gets removed. For avoiding this race, we need to close the pool to be deleted and sync its usage before actually deleting it. The issue was spotted by syzkaller. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Arnd Bergmann authored
commit a2125d02 upstream. The latest gcc-7 snapshot adds a warning to point out that when atk_read_value_old or atk_read_value_new fails, we copy uninitialized data into sensor->cached_value: drivers/hwmon/asus_atk0110.c: In function 'atk_input_show': drivers/hwmon/asus_atk0110.c:651:26: error: 'value' may be used uninitialized in this function [-Werror=maybe-uninitialized] Adding an error check avoids this. All versions of the driver are affected. Fixes: 2c03d07a ("hwmon: Add Asus ATK0110 support") Signed-off-by:
Luca Tettamanti <kronos.it@gmail.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Adrian Hunter authored
commit e2ebfb21 upstream. Disabling interrupts for even a millisecond can cause problems for some devices. That can happen when sdhci changes clock frequency because it waits for the clock to become stable under a spin lock. The spin lock is not necessary here. Anything that is racing with changes to the I/O state is already broken. The mmc core already provides synchronization via "claiming" the host. Although the spin lock probably should be removed from the code paths that lead to this point, such a patch would touch too much code to be suitable for stable trees. Consequently, for this patch, just drop the spin lock while waiting. Signed-off-by:
Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by:
-
Marcelo Henrique Cerri authored
commit d82c0d12 upstream. Reorder the operations in decompress_kernel() to ensure initrd is moved to a safe location before the bss section is zeroed. During decompression bss can overlap with the initrd and this can corrupt the initrd contents depending on the size of the compressed kernel (which affects where the initrd is placed by the bootloader) and the size of the bss section of the decompressor. Also use the correct initrd size when checking for overlaps with parmblock. Fixes: 06c0dd72 ([S390] fix boot failures with compressed kernels) Reviewed-by:
Joy Latten <joy.latten@canonical.com> Reviewed-by:
Vineetha HariPai <vineetha.hari.pai@canonical.com> Signed-off-by:
Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Eric Dumazet authored
commit aea92fb2 upstream. skb_cow(skb, sizeof(ip header)) is not very helpful in this context. First we need to use pskb_may_pull() to make sure the ip header is in skb linear part, then use skb_try_make_writable() to address clones issues. Fixes: 4c30719f ("[PKT_SCHED] dsmark: handle cloned and non-linear skb's") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Daniel Borkmann authored
commit 3697649f upstream. When we're dealing with clones and the area is not writeable, try harder and get a copy via pskb_expand_head(). Replace also other occurences in tc actions with the new skb_try_make_writable(). Reported-by:
Ashhad Sheikh <ashhadsheikh394@gmail.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
