Pull clock framework updates from Mike Turquette:
 "The clock framework changes contain the usual driver additions,
  enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
  devices.

  Additionally the framework core underwent a bit of surgery with two
  major changes:

   - The boundary between the clock core and clock providers (e.g clock
     drivers) is now more well defined with dedicated provider helper
     functions.  struct clk no longer maps 1:1 with the hardware clock
     but is a true per-user cookie which helps us tracker users of
     hardware clocks and debug bad behavior.

   - The addition of rate constraints for clocks.  Rate ranges are now
     supported which are analogous to the voltage ranges in the
     regulator framework.

  Unfortunately these changes to the core created some breakeage.  We
  think we fixed it all up but for this reason there are lots of last
  minute commits trying to undo the damage"

* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
  clk: Only recalculate the rate if needed
  Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
  clk: qoriq: Add support for the platform PLL
  powerpc/corenet: Enable CLK_QORIQ
  clk: Replace explicit clk assignment with __clk_hw_set_clk
  clk: Add __clk_hw_set_clk helper function
  clk: Don't dereference parent clock if is NULL
  MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
  clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
  clk: shmobile: div6: Avoid division by zero in .round_rate()
  clk: mxs: Fix invalid 32-bit access to frac registers
  clk: omap: compile legacy omap3 clocks conditionally
  clkdev: Export clk_register_clkdev
  clk: Add rate constraints to clocks
  clk: remove clk-private.h
  pci: xgene: do not use clk-private.h
  arm: omap2+ remove dead clock code
  clk: Make clk API return per-user struct clk instances
  clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
  clk: tegra: Add support for the Tegra132 CAR IP block
  ...

Pull VFIO updates from Alex Williamson:

 - IOMMU updates based on trace analysis
 - VFIO device request interface

* tag 'vfio-v3.20-rc1' of git://github.com/awilliam/linux-vfio:
  vfio-pci: Add device request interface
  vfio-pci: Generalize setup of simple eventfds
  vfio: Add and use device request op for vfio bus drivers
  vfio: Tie IOMMU group reference to vfio group
  vfio: Add device tracking during unbind
  vfio/type1: Add conditional rescheduling
  vfio/type1: Chunk contiguous reserved/invalid page mappings
  vfio/type1: DMA unmap chunking

Pull sound fixes from Takashi Iwai:
 "Here are a few small fix patches for 3.20-rc1:

   - Quirks for Denon and Lifecam USB-audio devices and HD-audio on HP
     laptops
   - A long-time regression fix for HDSP eMADI
   - Add missing DRAIN_TRIGGER flag set for ASoC intel-sst
   - Trivial fixes for sequencer core and HD-audio Tegra, a LINE6
     cleanup"

* tag 'sound-fix-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: usb: Fix support for Denon DA-300USB DAC (ID 154e:1003)
  ASoC: Intel: add SNDRV_PCM_INFO_DRAIN_TRIGGER flag
  ALSA: usb-audio: Don't attempt to get Lifecam HD-5000 sample rate
  ALSA: hda/tegra check correct return value from ioremap_resource
  ALSA: hdspm - Constrain periods to 2 on older cards
  ALSA: hda - enable mute led quirk for one more hp machine.
  ALSA: seq: potential out of bounds in do_control()
  ALSA: line6: Improve line6_read/write_data() interfaces

Pull thermal management fix from Zhang Rui:
 "One patch to fix a problem that all Exynos SoCs will break at boot
  time"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: exynos: fix: Check if data->tmu_read callback is present before read

Pull s390 fixes from Martin Schwidefsky:
 "Two patches to save some memory if CONFIG_NR_CPUS is large, a changed
  default for the use of compare-and-delay, and a couple of bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/spinlock: disabled compare-and-delay by default
  s390/mm: align 64-bit PIE binaries to 4GB
  s390/cacheinfo: coding style changes
  s390/cacheinfo: fix shared cpu masks
  s390/smp: reduce size of struct pcpu
  s390/topology: convert cpu_topology array to per cpu variable
  s390/topology: delay initialization of topology cpu masks
  s390/vdso: fix clock_gettime for CLOCK_THREAD_CPUTIME_ID, -2 and -3

Pull Intel Quark SoC support from Ingo Molnar:
 "This adds support for Intel Quark X1000 SoC boards, used in the low
  power 32-bit x86 Intel Galileo microcontroller board intended for the
  Arduino space.

  There's been some preparatory core x86 patches for Quark CPU quirks
  merged already, but this rounds it all up and adds Kconfig enablement.
  It's a clean hardware enablement addition tree at this point"

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/intel/quark: Fix simple_return.cocci warnings
  x86/intel/quark: Fix ptr_ret.cocci warnings
  x86/intel/quark: Add Intel Quark platform support
  x86/intel/quark: Add Isolated Memory Regions for Quark X1000

Pull ntp fix from Ingo Molnar:
 "An adjtimex interface regression fix for 32-bit systems"

[ A check that was added in a previous commit is really only a concern
  for 64bit systems, but was applied to both 32 and 64bit systems, which
  results in breaking 32bit systems.

  Thus the fix here is to make the check only apply to 64bit systems ]

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ntp: Fixup adjtimex freq validation on 32-bit systems

Pull locking fixes from Ingo Molnar:
 "Two fixes: the paravirt spin_unlock() corruption/crash fix, and an
  rtmutex NULL dereference crash fix"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/spinlocks/paravirt: Fix memory corruption on unlock
  locking/rtmutex: Avoid a NULL pointer dereference on deadlock

Pull misc x86 fixes from Ingo Molnar:
 "This contains:

   - EFI fixes
   - a boot printout fix
   - ASLR/kASLR fixes
   - intel microcode driver fixes
   - other misc fixes

  Most of the linecount comes from an EFI revert"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/ASLR: Avoid PAGE_SIZE redefinition for UML subarch
  x86/microcode/intel: Handle truncated microcode images more robustly
  x86/microcode/intel: Guard against stack overflow in the loader
  x86, mm/ASLR: Fix stack randomization on 64-bit systems
  x86/mm/init: Fix incorrect page size in init_memory_mapping() printks
  x86/mm/ASLR: Propagate base load address calculation
  Documentation/x86: Fix path in zero-page.txt
  x86/apic: Fix the devicetree build in certain configs
  Revert "efi/libstub: Call get_memory_map() to obtain map and desc sizes"
  x86/efi: Avoid triple faults during EFI mixed mode calls

Pull scheduler fixes from Ingo Molnar:
 "Thiscontains misc fixes: preempt_schedule_common() and io_schedule()
  recursion fixes, sched/dl fixes, a completion_done() revert, two
  sched/rt fixes and a comment update patch"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/rt: Avoid obvious configuration fail
  sched/autogroup: Fix failure to set cpu.rt_runtime_us
  sched/dl: Do update_rq_clock() in yield_task_dl()
  sched: Prevent recursion in io_schedule()
  sched/completion: Serialize completion_done() with complete()
  sched: Fix preempt_schedule_common() triggering tracing recursion
  sched/dl: Prevent enqueue of a sleeping task in dl_task_timer()
  sched: Make dl_task_time() use task_rq_lock()
  sched: Clarify ordering between task_rq_lock() and move_queued_task()

Pull x86 uprobe/kprobe fixes from Ingo Molnar:
 "This contains two uprobes fixes, an uprobes comment update and a
  kprobes fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  kprobes/x86: Mark 2 bytes NOP as boostable
  uprobes/x86: Fix 2-byte opcode table
  uprobes/x86: Fix 1-byte opcode tables
  uprobes/x86: Add comment with insn opcodes, mnemonics and why we dont support them

Merge branches 'core-urgent-for-linus' and 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull rcu fix and x86 irq fix from Ingo Molnar:

 - Fix a bug that caused an RCU warning splat.

 - Two x86 irq related fixes: a hotplug crash fix and an ACPI IRQ
   registry fix.

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rcu: Clear need_qs flag to prevent splat

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/irq: Check for valid irq descriptor in check_irq_vectors_for_cpu_disable()
  x86/irq: Fix regression caused by commit b568b860

The use of READ_ONCE() causes lots of warnings witht he pending paravirt
spinlock fixes, because those ends up having passing a member to a
'const' structure to READ_ONCE().

There should certainly be nothing wrong with using READ_ONCE() with a
const source, but the helper function __read_once_size() would cause
warnings because it would drop the 'const' qualifier, but also because
the destination would be marked 'const' too due to the use of 'typeof'.

Use a union of types in READ_ONCE() to avoid this issue.

Also make sure to use parenthesis around the macro arguments to avoid
possible operator precedence issues.
Tested-by: Ingo Molnar <mingo@kernel.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull kgdb/kdb updates from Jason Wessel:
 "KGDB/KDB New:
   - KDB: improved searching
   - No longer enter debug core on panic if panic timeout is set

  KGDB/KDB regressions / cleanups
   - fix pdf doc build errors
   - prevent junk characters on kdb console from printk levels"

* tag 'for_linux-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
  kgdb, docs: Fix <para> pdfdocs build errors
  debug: prevent entering debug mode on panic/exception.
  kdb: Const qualifier for kdb_getstr's prompt argument
  kdb: Provide forward search at more prompt
  kdb: Fix a prompt management bug when using | grep
  kdb: Remove stack dump when entering kgdb due to NMI
  kdb: Avoid printing KERN_ levels to consoles
  kdb: Fix off by one error in kdb_cpu()
  kdb: fix incorrect counts in KDB summary command output

Pull IPMI driver updates from Corey Minyard:
 "Some minor fixes and cleanups, nothing big.

  In for-next for a while and I've done some extensive beating on the
  driver since I have it working in qemu and can do creatively cruel
  things to it"

* tag 'for-linus-3.20-1' of git://git.code.sf.net/p/openipmi/linux-ipmi:
  ipmi: Fix a memory ordering issue
  ipmi: Remove uses of return value of seq_printf
  ipmi: Use is_visible callback for conditional sysfs entries
  ipmi: Free ipmi_recv_msg messages from the linked list on close
  ipmi: avoid gcc warning
  ipmi: Update timespec usage to timespec64
  ipmi: Cleanup DEBUG_TIMING ifdef usage
  drivers:char:ipmi: Remove unneeded FIXME comment in the file,ipmi_si_intf.c
  char: ipmi: Remove obsolete cleanup for clientdata
  ipmi: Remove a FIXME for slab conversion

The exynos_tmu_data() function should on entrance test not only for valid
data pointer, but also for data->tmu_read one.
It is important, since afterwards it is dereferenced to get temperature code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Commit f47233c2 ("x86/mm/ASLR: Propagate base load address
calculation") causes PAGE_SIZE redefinition warnings for UML
subarch  builds. This is caused by added includes that were
leftovers from previous  patch versions are are not actually
needed (especially page_types.h  inlcude in module.c). Drop
those stray includes.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1502201017240.28769@pobox.suse.czSigned-off-by: Ingo Molnar <mingo@kernel.org>

We don't really need to recalculate the effective rate of a clock when a
per-user clock is removed, if the constraints of the later aren't
limiting the requested rate.

This was causing problems with clocks that never had a rate set before,
as rate_req would be zero. Though this could be considered a bug in the
implementation of those clocks, this should be checked somewhere else.

Fixes: 1c8e6004 ("clk: Add rate constraints to clocks")
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

From a locking point of view it is safe to check waiting_msg without
a lock, but there is a memory ordering issue that causes it to
possibly not be set right when viewed from another processor.  We are
already claiming a lock right after that, move the check to inside
the lock to enforce the memory ordering.
Signed-off-by: Corey Minyard <cminyard@mvista.com>

The seq_printf like functions will soon be changed to return void.

Convert these uses to check seq_has_overflowed instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>

Instead of manual calls of device_create_file() and
device_remove_file(), implement the condition in is_visible callback
for the attribute group and put these entries to the group, too.
This simplifies the code and avoids the possible races.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>

This adds a loop through the elements in the linked list, recv_msgs using
list_for_entry_safe in order to free messages in this list.  In addition
we are using the safe version of this marco in order to prevent use after
bugs related to deleting the element we are on currently by holding a
pointer to the next element after the current one we are on and freeing
with the function, ipmi_free_recv_msg internally in this loop.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>

A new harmless warning has come up on ARM builds with gcc-4.9:

drivers/char/ipmi/ipmi_msghandler.c: In function 'smi_send.isra.11':
include/linux/spinlock.h:372:95: warning: 'flags' may be used uninitialized in this function [-Wmaybe-uninitialized]
  raw_spin_unlock_irqrestore(&lock->rlock, flags);
                                                                                               ^
drivers/char/ipmi/ipmi_msghandler.c:1490:16: note: 'flags' was declared here
  unsigned long flags;
                ^

This could be worked around by initializing the 'flags' variable, but it
seems better to rework the code to avoid this.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7ea0ed2b ("ipmi: Make the message handler easier to use for SMI interfaces")
Signed-off-by: Corey Minyard <cminyard@mvista.com>

As part of the internal y2038 cleanup, this patch removes
timespec usage in the ipmi driver, replacing it timespec64

Cc: openipmi-developer@lists.sourceforge.net
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Corey Minyard <minyard@mvista.com>

The driver uses #ifdef DEBUG_TIMING in order to conditionally print out
timestamped debug messages. Unfortunately it adds the ifdefs all over the
usage sites.

This patch cleans it up by adding a debug_timestamp() function which
is compiled out if DEBUG_TIMING isn't present. This cleans up all
the ugly ifdefs in the function logic.

Cc: openipmi-developer@lists.sourceforge.net
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Corey Minyard <minyard@mvista.com>

Removes a no longer needed FIXME comment in the function,acpi_gpe_irq_setup
for the file,ipmi_si_intf.c. This comment is no longer needed as clearly we
are passing the correct level of  ACPI_GPE_LEVEL_TRIGGERED to the installer
function,acpi_install_gpe_handler due to no breakage after years of using
this ACPI level in the function,acpi_install_gpe_handler.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>

A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit or error. This is obsolete meanwhile, the core will do it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>

There can't be more than a few IPMI messages allocated at any one time,
so converting the messages to slabs would be a waste.  So just remove
the FIXME.
Suggested-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>

Pull more thermal managament updates from Zhang Rui:
 "Specifics:

   - Exynos thermal driver refactoring.  Several cleanups, code
     optimization, unused symbols removal, and unused feature removal in
     Exynos thermal driver.  Thanks Lukasz for this effort.

   - Exynos thermal driver support to OF thermal.  After the code
     refactoring, the driver earned the support to OF thermal.  Chip
     thermal data were moved from driver code to DTS, reducing the code
     footprint.  Thanks Lukasz for this.

   - After receiving the OF thermal support, the exynos thermal driver
     now must allow modular build.  Thanks Arnd for detecting, reporting
     and fixing this.

   - Exynos thermal driver support to Exynos 7 SoC.  Thanks Abhilash for
     this.

   - Accurate temperature reporting on Rockchip thermal driver, thanks
     to Caesar.

   - Fix on how OF thermal enables its zones, thanks Lukasz for fixing.

   - Fixes in OF thermal examples under Documentation/.  Thanks Srinivas
     for fixing"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: exynos: Add TMU support for Exynos7 SoC
  dts: Documentation: Add documentation for Exynos7 SoC thermal bindings
  cpufreq: exynos: allow modular build
  thermal: Fix examples in DT documentation
  thermal: exynos: Correct sanity check at exynos_report_trigger() function
  thermal: Kconfig: Remove config for not used EXYNOS_THERMAL_CORE
  thermal: exynos: Remove exynos_tmu_data.c file
  thermal: rockchip: make temperature reporting much more accurate
  thermal: exynos: Remove exynos_thermal_common.[c|h] files
  thermal: samsung: core: Exynos TMU rework to use device tree for configuration
  dts: Documentation: Update exynos-thermal.txt example for Exynos5440
  dts: Documentation: Extending documentation entry for exynos-thermal
  cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered
  thermal: exynos: Modify exynos thermal code to use device tree for cpu cooling configuration
  thermal: exynos: Provide thermal_exynos.h file to be included in device tree files
  thermal: exynos: cosmetic: Correct comment format
  thermal: of: Enable thermal_zoneX when sensor is correctly added

Since _PAGE_PROTNONE aliases _PAGE_GLOBAL it is only valid if
_PAGE_PRESENT is clear.  Make pte_protnone() and pmd_protnone() check
for this.

This fixes a 64-bit Xen PV guest regression introduced by 8a0516ed
("mm: convert p[te|md]_numa users to p[te|md]_protnone_numa").  Any
userspace process would endlessly fault.

In a 64-bit PV guest, userspace page table entries have _PAGE_GLOBAL set
by the hypervisor.  This meant that any fault on a present userspace
entry (e.g., a write to a read-only mapping) would be misinterpreted as
a NUMA hinting fault and the fault would not be correctly handled,
resulting in the access endlessly faulting.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull btrfs updates from Chris Mason:
 "This pull is mostly cleanups and fixes:

   - The raid5/6 cleanups from Zhao Lei fixup some long standing warts
     in the code and add improvements on top of the scrubbing support
     from 3.19.

   - Josef has round one of our ENOSPC fixes coming from large btrfs
     clusters here at FB.

   - Dave Sterba continues a long series of cleanups (thanks Dave), and
     Filipe continues hammering on corner cases in fsync and others

  This all was held up a little trying to track down a use-after-free in
  btrfs raid5/6.  It's not clear yet if this is just made easier to
  trigger with this pull or if its a new bug from the raid5/6 cleanups.
  Dave Sterba is the only one to trigger it so far, but he has a
  consistent way to reproduce, so we'll get it nailed shortly"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (68 commits)
  Btrfs: don't remove extents and xattrs when logging new names
  Btrfs: fix fsync data loss after adding hard link to inode
  Btrfs: fix BUG_ON in btrfs_orphan_add() when delete unused block group
  Btrfs: account for large extents with enospc
  Btrfs: don't set and clear delalloc for O_DIRECT writes
  Btrfs: only adjust outstanding_extents when we do a short write
  btrfs: Fix out-of-space bug
  Btrfs: scrub, fix sleep in atomic context
  Btrfs: fix scheduler warning when syncing log
  Btrfs: Remove unnecessary placeholder in btrfs_err_code
  btrfs: cleanup init for list in free-space-cache
  btrfs: delete chunk allocation attemp when setting block group ro
  btrfs: clear bio reference after submit_one_bio()
  Btrfs: fix scrub race leading to use-after-free
  Btrfs: add missing cleanup on sysfs init failure
  Btrfs: fix race between transaction commit and empty block group removal
  btrfs: add more checks to btrfs_read_sys_array
  btrfs: cleanup, rename a few variables in btrfs_read_sys_array
  btrfs: add checks for sys_chunk_array sizes
  btrfs: more superblock checks, lower bounds on devices and sectorsize/nodesize
  ...

Pull Ceph changes from Sage Weil:
 "On the RBD side, there is a conversion to blk-mq from Christoph,
  several long-standing bug fixes from Ilya, and some cleanup from
  Rickard Strandqvist.

  On the CephFS side there is a long list of fixes from Zheng, including
  improved session handling, a few IO path fixes, some dcache management
  correctness fixes, and several blocking while !TASK_RUNNING fixes.

  The core code gets a few cleanups and Chaitanya has added support for
  TCP_NODELAY (which has been used on the server side for ages but we
  somehow missed on the kernel client).

  There is also an update to MAINTAINERS to fix up some email addresses
  and reflect that Ilya and Zheng are doing most of the maintenance for
  RBD and CephFS these days.  Do not be surprised to see a pull request
  come from one of them in the future if I am unavailable for some
  reason"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (27 commits)
  MAINTAINERS: update Ceph and RBD maintainers
  libceph: kfree() in put_osd() shouldn't depend on authorizer
  libceph: fix double __remove_osd() problem
  rbd: convert to blk-mq
  ceph: return error for traceless reply race
  ceph: fix dentry leaks
  ceph: re-send requests when MDS enters reconnecting stage
  ceph: show nocephx_require_signatures and notcp_nodelay options
  libceph: tcp_nodelay support
  rbd: do not treat standalone as flatten
  ceph: fix atomic_open snapdir
  ceph: properly mark empty directory as complete
  client: include kernel version in client metadata
  ceph: provide seperate {inode,file}_operations for snapdir
  ceph: fix request time stamp encoding
  ceph: fix reading inline data when i_size > PAGE_SIZE
  ceph: avoid block operation when !TASK_RUNNING (ceph_mdsc_close_sessions)
  ceph: avoid block operation when !TASK_RUNNING (ceph_get_caps)
  ceph: avoid block operation when !TASK_RUNNING (ceph_mdsc_sync)
  rbd: fix error paths in rbd_dev_refresh()
  ...

Pull thermal managament updates from Zhang Rui:
 "Specifics:

   - Abstract the code and introduce helper functions for all int340x
     thermal drivers.  From: Srinivas Pandruvada.

   - Reorganize the ACPI LPAT table support code so that it can be
     shared for both ACPI PMIC driver and int340x thermal driver.

   - Add support for Braswell in intel_soc_dts thermal driver.

   - a couple of small fixes/cleanups for step_wise governor and int340x
     thermal driver"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  Thermal/int340x_thermal: remove unused uuids.
  thermal: step_wise: spelling fixes
  thermal: int340x: fix sparse warning
  Thermal/int340x: LPAT conversion for temperature
  ACPI / PMIC: Use common LPAT table handling functions
  ACPI / LPAT: Common table processing functions
  thermal: Intel SoC DTS: Add Braswell support
  Thermal/int340x/int3402: Provide notification support
  Thermal/int340x/processor_thermal: Add thermal zone support
  Thermal/int340x/int3403: Use int340x thermal API
  Thermal/int340x/int3402: Use int340x thermal API
  Thermal/int340x: Add common thermal zone handler

Pull two EDAC fixes from Borislav Petkov:

 - A fix to sb_edac for proper detection on SNB machines

 - A fix to amd64_edac to not explode on Numascale machines with more
   than 16 memory controllers, from Daniel J Blueman.

* tag 'edac_fixes_for_3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  EDAC, amd64_edac: Prevent OOPS with >16 memory controllers
  sb_edac: Fix detection on SNB machines

Merge tag 'platform-drivers-x86-v3.20-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull platform driver update from Darren Hart:
 "This includes a significant update to the toshiba_acpi driver,
  bringing it to feature parity with the Windows driver, followed by
  some needed cleanups.

  The other changes are mostly minor updates, quirks, sparse fixes, or
  cleanups.

  Details:

   - toshiba_acpi:
       Add support for missing features from the Windows driver, bump the
       sysfs version, and clean up the driver.

   - thinkpad_acpi:
       BIOS string versions, unhandled hkey events.

   - msamsung-laptop:
       Add native backlight quirk, enable better lid handling.

   - intel_scu_ipc:
       Read resources from PCI configuration

   - other:
       Fix sparse warnings, general cleanups"

* tag 'platform-drivers-x86-v3.20-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (34 commits)
  toshiba_acpi: Cleanup GPL header
  toshiba_acpi: Cleanup comment blocks and capitalization
  toshiba_acpi: Make use of DEVICE_ATTR_{RO, RW} macros
  toshiba_acpi: Drop the toshiba_ prefix from sysfs function names
  toshiba_acpi: Move sysfs function and struct declarations further down
  Documentation/ABI: Add file describing the sysfs entries for toshiba_acpi
  toshiba_acpi: Clean file according to coding style
  toshiba_acpi: Bump version number to 0.21
  toshiba_acpi: Add support to enable/disable USB 3
  toshiba_acpi: Add support for Panel Power ON
  toshiba_acpi: Add support for Keyboard functions mode
  toshiba_acpi: Add fan entry to sysfs
  toshiba_acpi: Add version entry to sysfs
  thinkpad_acpi: support new BIOS version string pattern
  thinkpad_acpi: unhandled hkey event
  toshiba_acpi: Make toshiba_eco_mode_available more robust
  classmate-laptop: Fix sparse warning (0 as NULL)
  Sony-laptop: Fix sparse warning (make undeclared var static)
  thinkpad_acpi.c: Fix sparse warning (make undeclared var static)
  samsung-laptop.c: Prefer kstrtoint over single variable sscanf
  ...

kgdb.pdf failed to build from 'make pdfdocs' giving errors such as:

jade:... Documentation/DocBook/kgdb.xml:200:8:E:
document type does not allow element "para" here; missing one of
"footnote", "caution", "important", "note", "tip", "warning",
"blockquote", "informalexample" start-tag

Fixing minor <para> and <sect> issues allows kgdb.pdf to be generated
under Fedora20.

Originally submitted by rajaneesh.acharya@yahoo.com in 2011, discussed here:
http://permalink.gmane.org/gmane.linux.documentation/3954
as patch:
 The following are the enhancements that removed the errors
 while issuing "make pdfdocs"

[graham.whaley@intel.com: Improved commit message and ported to 3.18.1]
Signed-off-by: Graham Whaley <graham.whaley@intel.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

On non-developer devices, kgdb prevents the device from rebooting
after a panic.

Incase of panics and exceptions, to allow the device to reboot, prevent
entering debug mode to avoid getting stuck waiting for the user to
interact with debugger.

To avoid entering the debugger on panic/exception without any extra
configuration, panic_timeout is being used which can be set via
/proc/sys/kernel/panic at run time and CONFIG_PANIC_TIMEOUT sets the
default value.

Setting panic_timeout indicates that the user requested machine to
perform unattended reboot after panic. We dont want to get stuck waiting
for the user input incase of panic.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: linux-kernel@vger.kernel.org
Cc: Android Kernel Team <kernel-team@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Colin Cross <ccross@android.com>
[Kiran: Added context to commit message.
panic_timeout is used instead of break_on_panic and
break_on_exception to honor CONFIG_PANIC_TIMEOUT
Modified the commit as per community feedback]
Signed-off-by: Kiran Raparthy <kiran.kumar@linaro.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

All current callers of kdb_getstr() can pass constant pointers via the
prompt argument. This patch adds a const qualification to make explicit
the fact that this is safe.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

Currently kdb allows the output of comamnds to be filtered using the
| grep feature. This is useful but does not permit the output emitted
shortly after a string match to be examined without wading through the
entire unfiltered output of the command. Such a feature is particularly
useful to navigate function traces because these traces often have a
useful trigger string *before* the point of interest.

This patch reuses the existing filtering logic to introduce a simple
forward search to kdb that can be triggered from the more prompt.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

Currently when the "| grep" feature is used to filter the output of a
command then the prompt is not displayed for the subsequent command.
Likewise any characters typed by the user are also not echoed to the
display. This rather disconcerting problem eventually corrects itself
when the user presses Enter and the kdb_grepping_flag is cleared as
kdb_parse() tries to make sense of whatever they typed.

This patch resolves the problem by moving the clearing of this flag
from the middle of command processing to the beginning.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>