Added code to take FW dump.
o Driver queries FW at the init time and gets the dump template
o It takes FW dump as per the dump template
o Level of FW dump (and its size) is configured via dump flag
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sending mbox cmds require multiple steps of writing to the DB register and polling
for an ack. Gettting interrupted in the middle by a signal breaks the mbox protocol.
Use msleep() to not get interrupted.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If waiting on POST returns prematurely (due to a signal), abort polling and return an error.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added code to take FW dump via ethtool. Dump level can be controlled via setting the
dump flag. A get function is provided to query the current setting of the dump flag.
Dump data is obtained from the driver via a separate get function.

Changes from v3:
Fixed buffer length issue in ethtool_get_dump_data function.
Updated kernel doc for ethtool_dump struct and get_dump_flag function.

Changes from v2:
Provided separate commands for get flag and data.
Check for minimum of the two buffer length obtained via ethtool and driver and
use that for dump buffer
Pass up the driver return error codes up to the caller.
Added kernel doc comments.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Save a bit of space.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I swear none of my compilers warned about this, yet it is so
obvious.

> net/ipv4/ip_forward.c: In function 'ip_forward':
> net/ipv4/ip_forward.c:87: warning: 'iph' may be used uninitialized in this function
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

No matter what kind of header mangling occurs due to IP options
processing, rt->rt_dst will always equal iph->daddr in the packet.

So we can safely use iph->daddr instead of rt->rt_dst here.
Signed-off-by: David S. Miller <davem@davemloft.net>

We already copy the 4-byte nexthop from the options block into
local variable "nexthop" for the route lookup.

Re-use that variable instead of memcpy()'ing again when assigning
to iph->daddr after the route lookup succeeds.
Signed-off-by: David S. Miller <davem@davemloft.net>

All call sites conditionalize the call to ip_options_rcv_srr()
with a check of opt->srr, so no need to check it again there.
Signed-off-by: David S. Miller <davem@davemloft.net>

This should also fix updating of vlan_features and propagating changes to
VLAN devices on the bond.

Side effect: it allows user to force-disable some offloads on the bond
interface.

Note: NETIF_F_VLAN_CHALLENGED is managed by bond_fix_features() now.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

It will be needed by bonding and other drivers changing vlan_features
after ndo_init callback.

As a bonus, this includes kernel-doc for netdev_update_features().
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes:
- while making NTB, driver shall check if device dwNtbOutMaxSize is higher than
 host value and shall add a short packet if this is the case
- previous temporary patch for this issue is replaced by this one
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove all remaining references to rt->rt_{src,dst}
by using dest->dst_saddr to cache saddr (used for TUN mode).
For ICMP in FORWARD hook just restrict the rt_mode for NAT
to disable LOCALNODE. All other modes do not allow
IP_VS_RT_MODE_RDR, so we should be safe with the ICMP
forwarding. Using cp->daddr as replacement for rt_dst
is safe for all modes except BYPASS, even when cp->dest is
NULL because it is cp->daddr that is used to assign cp->dest
for sync-ed connections.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can simply track what destination address is used based upon which
code block is taken at the top of the function.
Signed-off-by: David S. Miller <davem@davemloft.net>

[ Add some cases I missed, from Julian Anastasov ]
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds tg3_set_features() to handle loopback mode. Currently the
capability is added for the devices which support internal MAC loopback mode.
So when enabled, it enables internal-MAC loopback.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use tty_insert_flip_string and tty_flip_buffer_push to deliver incoming data
packets from the IrDA device instead of delivering the packets directly to the
line discipline. Following later approach resulted in warning "Sleeping function
called from invalid context".
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michał Mirosław's patch (http://patchwork.ozlabs.org/patch/94421/) fixes the
issue (http://patchwork.ozlabs.org/patch/94188/) about not populating FCoE related
flags correctly on vlan devices. However, only NETIF_F_FCOE_CRC is part of the
NETIF_F_ALL_TX_OFFLOADS right now, where weed NETIF_F_FCOE_MTU and NETIF_F_FSO
as well.

Therefore, add NETIF_F_ALL_FCOE to indicate feature flags used by FCoE TX offloads.
These include NETIF_F_FCOE_CRC, NETIF_F_FCOE_MTU, and NETIF_F_FSO and add them to
be part of NETIF_F_ALL_TX_OFFLOADS. This would eventually make sure all FCoE needed
flags are populated properly to vlan devices.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix VLAN features propagation for devices which change vlan_features.
For this to work, driver needs to make sure netdev_features_changed()
gets called after the change (it is e.g. after ndo_set_features()).

Side effect is that a user might request features that will never
be enabled on a VLAN device.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The issue was introduced in commit eed2a12f.
Signed-off-by: Franco Fichtner <franco@lastsummer.de>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When removing last vlan from a device, garp_uninit_applicant() calls
synchronize_rcu() to make sure no user can still manipulate struct
garp_applicant before we free it.

Use call_rcu() instead, as a step to further net_device dismantle
optimizations.

Add the temporary garp_cleanup_module() function to make sure no pending
call_rcu() are left at module unload time [ this will be removed when
kfree_rcu() is available ]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Resending this patch with few changes.

Avoid multiple queues when MSI or MSI-X not available

Limit number of Tx queues to 1 if MSI/MSI-X support is not configured in
the kernel. This will make number of tx and rx queues equal when MSI/X
is not configured thus providing better performance.
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's already known non-null above.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This variable only needs initialization when cmsgs.info
is NULL.

Use memset to ensure padding is also zeroed so
kernel doesn't leak any data.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While trying to remove useless synchronize_rcu() calls, I found l2tp is
indeed incorrectly using two of such calls, but also bumps tunnel
refcount after list insertion.

tunnel refcount must be incremented before being made publically visible
by rcu readers.

This fix can be applied to 2.6.35+ and might need a backport for older
kernels, since things were shuffled in commit fd558d18
(l2tp: Split pppol2tp patch into separate l2tp and ppp parts)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: James Chapman <jchapman@katalix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Start/stop TX queue is controlled by TX queue "used" counter.
It is incremented while WRBs are posted to TX queue and
decremented when TX completions are received. This counter was
getting decremented before HW is informed about processing of TX
completions. As used counter is decremented, transmit function
posts new WRBs and creates completion queue full scenario in HW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use OPCODE_COMMON_NTWK_RX_FILTER command for promiscous mode as
OPCODE_ETH_PROMISCUOUS command is getting deprecated.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of UE, do not dump registers for Lancer as they are not
supported.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Disable coalesce water mark mode of CQ for Lancer
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Lancer if a frame is DMAed partially due to lack of RX buffers,
an error completion is sent with packet size as zero and num_recvd
indicating number of used buffers. These buffers need to be freed
and packet dropped.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/benet/be_main.c

TTY layer expects 0 if the ldisc->open operation succeeded.
Reported-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like other mobile broadband device ethernet interfaces, mark the LG
VL600 with the 'wwan' devtype so userspace knows it needs additional
configuration via the AT port before the interface can be used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike the standard case, disabled anti replay detection needs some
nontrivial extra treatment on ESN. RFC 4303 states:

Note: If a receiver chooses to not enable anti-replay for an SA, then
the receiver SHOULD NOT negotiate ESN in an SA management protocol.
Use of ESN creates a need for the receiver to manage the anti-replay
window (in order to determine the correct value for the high-order
bits of the ESN, which are employed in the ICV computation), which is
generally contrary to the notion of disabling anti-replay for an SA.

So return an error if an ESN state with disabled anti replay detection
is inserted for now and add the extra treatment later if we need it.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As it is, we assign the outer modes output function to the dst entry
when we create the xfrm bundle. This leads to two problems on interfamily
scenarios. We might insert ipv4 packets into ip6_fragment when called
from xfrm6_output. The system crashes if we try to fragment an ipv4
packet with ip6_fragment. This issue was introduced with git commit
ad0081e4 (ipv6: Fragment locally generated tunnel-mode IPSec6 packets
as needed). The second issue is, that we might insert ipv4 packets in
netfilter6 and vice versa on interfamily scenarios.

With this patch we assign the inner mode output function to the dst entry
when we create the xfrm bundle. So xfrm4_output/xfrm6_output from the inner
mode is used and the right fragmentation and netfilter functions are called.
We switch then to outer mode with the output_finish functions.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 44345724 (factorize sync-rcu call in
unregister_netdevice_many) mistakenly removed one test from dev_close()

Following actions trigger a BUG :

modprobe bonding
modprobe dummy
ifconfig bond0 up
ifenslave bond0 dummy0
rmmod dummy

dev_close() must not close a non IFF_UP device.

With help from Frank Blaschka and Einar EL Lueck
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Reported-by: Einar EL Lueck <ELELUECK@de.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip link add link eth2 eth2.103 type vlan id 103 gvrp on loose_binding on
ip link set eth2.103 up
rmmod tg3    # driver providing eth2

 BUG: unable to handle kernel NULL pointer dereference at           (null)
 IP: [<ffffffffa0030c9e>] garp_request_leave+0x3e/0xc0 [garp]
 PGD 11d251067 PUD 11b9e0067 PMD 0
 Oops: 0000 [#1] SMP
 last sysfs file: /sys/devices/virtual/net/eth2.104/ifindex
 CPU 0
 Modules linked in: tg3(-) 8021q garp nfsd lockd auth_rpcgss sunrpc libphy sg [last unloaded: x_tables]

 Pid: 11494, comm: rmmod Tainted: G        W   2.6.39-rc6-00261-gfd71257-dirty #580 HP ProLiant BL460c G6
 RIP: 0010:[<ffffffffa0030c9e>]  [<ffffffffa0030c9e>] garp_request_leave+0x3e/0xc0 [garp]
 RSP: 0018:ffff88007a19bae8  EFLAGS: 00010286
 RAX: 0000000000000000 RBX: ffff88011b5e2000 RCX: 0000000000000002
 RDX: 0000000000000000 RSI: 0000000000000175 RDI: ffffffffa0030d5b
 RBP: ffff88007a19bb18 R08: 0000000000000001 R09: ffff88011bd64a00
 R10: ffff88011d34ec00 R11: 0000000000000000 R12: 0000000000000002
 R13: ffff88007a19bc48 R14: ffff88007a19bb88 R15: 0000000000000001
 FS:  0000000000000000(0000) GS:ffff88011fc00000(0063) knlGS:00000000f77d76c0
 CS:  0010 DS: 002b ES: 002b CR0: 000000008005003b
 CR2: 0000000000000000 CR3: 000000011a675000 CR4: 00000000000006f0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
 Process rmmod (pid: 11494, threadinfo ffff88007a19a000, task ffff8800798595c0)
 Stack:
  ffff88007a19bb36 ffff88011c84b800 ffff88011b5e2000 ffff88007a19bc48
  ffff88007a19bb88 0000000000000006 ffff88007a19bb38 ffffffffa003a5f6
  ffff88007a19bb38 670088007a19bba8 ffff88007a19bb58 ffffffffa00397e7
 Call Trace:
  [<ffffffffa003a5f6>] vlan_gvrp_request_leave+0x46/0x50 [8021q]
  [<ffffffffa00397e7>] vlan_dev_stop+0xb7/0xc0 [8021q]
  [<ffffffff8137e427>] __dev_close_many+0x87/0xe0
  [<ffffffff8137e507>] dev_close_many+0x87/0x110
  [<ffffffff8137e630>] rollback_registered_many+0xa0/0x240
  [<ffffffff8137e7e9>] unregister_netdevice_many+0x19/0x60
  [<ffffffffa00389eb>] vlan_device_event+0x53b/0x550 [8021q]
  [<ffffffff8143f448>] ? ip6mr_device_event+0xa8/0xd0
  [<ffffffff81479d03>] notifier_call_chain+0x53/0x80
  [<ffffffff81062539>] __raw_notifier_call_chain+0x9/0x10
  [<ffffffff81062551>] raw_notifier_call_chain+0x11/0x20
  [<ffffffff8137df82>] call_netdevice_notifiers+0x32/0x60
  [<ffffffff8137e69f>] rollback_registered_many+0x10f/0x240
  [<ffffffff8137e85f>] rollback_registered+0x2f/0x40
  [<ffffffff8137e8c8>] unregister_netdevice_queue+0x58/0x90
  [<ffffffff8137e9eb>] unregister_netdev+0x1b/0x30
  [<ffffffffa005d73f>] tg3_remove_one+0x6f/0x10b [tg3]

We should call vlan_gvrp_request_leave() from unregister_vlan_dev(),
not from vlan_dev_stop(), because vlan_gvrp_uninit_applicant()
is called right after unregister_netdevice_queue(). In batch mode,
unregister_netdevice_queue() doesn’t immediately call vlan_dev_stop().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>