It will now give ppc64 on 64bit platforms and ppc on 32bit
platforms.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

and use start_thread for both 32 and 64 bit bineries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

and use it in misc_32.S
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

Also simplify arch/ppc64/kernel/Makefile
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

This removes three headers from include/asm-ppc64 that are now in
include/asm-powerpc and are sufficiently similar that they can be
used with ARCH=ppc64.
Signed-off-by: Paul Mackerras <paulus@samba.org>

Recent commits upstream have changed files which are currently
duplicated in arch/powerpc and include/asm-powerpc.  This updates
them with the corresponding changes.
Signed-off-by: Paul Mackerras <paulus@samba.org>

We weren't computing the size of the hash table correctly on iSeries
because the relevant code in prom.c was #ifdef CONFIG_PPC_PSERIES.
This moves the code to hash_utils_64.c, makes it unconditional, and
cleans it up a bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>

On ARCH=ppc64 we were getting htab_hash_mask recalculated
to the correct value for our particular machine by accident.
In the merge tree, that code was commented out, so htab_hash_mask
was being corrupted.

We now set ppc64_pft_size instead which gets htab_has_mask
calculated correctly for us later.  We should put an
ibm,pft-size property in the device tree at some point.

Also set -mno-minimal-toc in some makefiles.
Allow iSeries to configure PROC_DEVICETREE.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

We were not doing alignment properly when remapping the kernel image.

What we want is a 4MB aligned physical address to map at KERNBASE.
Mistakedly we were 4MB aligning the virtual address where the kernel
initially sits, that's wrong.

Instead, we should PAGE align the virtual address, then 4MB align the
physical address result the prom gives to us.
Signed-off-by: David S. Miller <davem@davemloft.net>

Refuse to install a page into a mapping if the mapping count is already
ridiculously large.

You probably cannot trigger this on 32-bit architectures, but on a
64-bit setup we should protect against it.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Newer gcc's are generating this relocation, so the module loader needs to
handle it.
Signed-off-by: Peter Bergner <bergner@vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* bttv-cards.c:
- Enable S-Video input on DViCO FusionHDTV5 Lite
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch prevents illegal traps from causing m32r kernel's infinite loop
execution.
Signed-off-by: Naoto Sugai <sugai@isl.melco.co.jp>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Nir Tzachar <tzachar@cs.bgu.ac.il> points out that if an ELF file specifies a
zero-length bss at a whacky address, we cannot load that binary because
padzero() tries to zero out the end of the page at the whacky address, and
that may not be writeable.

See also http://bugzilla.kernel.org/show_bug.cgi?id=5411

So teach load_elf_binary() to skip the bss settng altogether if the elf file
has a zero-length bss segment.

Cc: Roland McGrath <roland@redhat.com>
Cc: Daniel Jacobowitz <dan@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

I've noticed that the calculations for seg_size and nr_segs in
__dma_sync_page_highmem() (arch/ppc/kernel/dma-mapping.c) are wrong.  The
incorrect calculations can result in either an oops or a panic when running
fsck depending on the size of the partition.

The problem with the seg_size calculation is that it can result in a
negative number if size is offset > size.  The problem with the nr_segs
caculation is returns the wrong number of segments, e.g.  it returns 1 when
size is 200 and offset is 4095, when it should return 2 or more.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Revert this recent correctness change: Douglas Crosher <dcrosher@scieneer.com>
reported that it broke an existing application, and that madvise() works
without error on anonymous mappings on Solaris.

This means that madvise() will remain non-standards-compliant: we should
return -EBADF for all requests against non-file-backed vma's, but Linux only
does this for MADV_WILLNEED requests.
Signed-off-by: Suzuki K P <suzuki@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Here is a compatibility fix between Linux and Solaris when used with VxFS
filesystems: Solaris usually accepts acl entries in any order, but with
VxFS it replies with NFSERR_INVAL when it sees a four-entry acl that is not
in canonical form.  It may also fail with other non-canonical acls -- I
can't tell, because that case never triggers: We only send non-canonical
acls when we fake up an ACL_MASK entry.

Instead of adding fake ACL_MASK entries at the end, inserting them in the
correct position makes Solaris+VxFS happy.  The Linux client and server
sides don't care about entry order.  The three-entry-acl special case in
which we need a fake ACL_MASK entry was handled in xdr_nfsace_encode.  The
patch moves this into nfsacl_encode.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

v9fs_file_read and v9fs_file_write use kmalloc to allocate buffers as big
as the data buffer received as parameter.  kmalloc cannot be used to
allocate buffers bigger than 128K, so reading/writing data in chunks bigger
than 128k fails.

This patch reorganizes v9fs_file_read and v9fs_file_write to allocate only
buffers as big as the maximum data that can be sent in one 9P message.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

In the current dell_rbu code ver 2.0 the packet update mechanism makes the
user app dump every individual packet in to the driver.

This adds in efficiency as every packet update makes the
/sys/class/firmware/dell_rbu/loading and data files to disappear and reappear
again.  Thus the user app needs to wait for the files to reappear to dump
another packet.  This slows down the packet update tremendously in case of
large number of packets.  I am submitting a new patch for dell_rbu which will
change the way we do packet updates;

In the new method the user app will create a new single file which has already
packetized the rbu image and all the packets are now staged in this file.

This driver also creates a new entry in
/sys/devices/platform/dell_rbu/packet_size ; the user needs to echo the packet
size here before downloading the packet file.

The user should do the following:

 create one single file which has all the packets stacked together.
 echo the packet size in to /sys/devices/platform/dell_rbu/packet_size.
 echo 1 > /sys/class/firmware/dell_rbu/loading
 cat the packetfile > /sys/class/firmware/dell_rbu/data
 echo 0 > /sys/class/firmware/dell_rbu/loading

The driver takes the file which came through /sys/class/firmware/dell_rbu/data
and takes chunks of paket_size data from it and place in contiguous memory.

This makes packet update process very efficient and fast.  As all the packet
update happens in one single operation.  The user can still read back the
downloaded file from /sys/devices/platform/dell_rbu/data.
Signed-off-by: Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

pSeries_irq_bus_setup is marked __devinit but references s7a_workaround
which is marked __initdata.

Depending on who got the memory for s7a_workaround (and if the value was
now positive), it was possible for PCI hotplugged devices to have 3
subtracted from their interrupt number.  This would happen randomly and
caused me much confusion :)
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Search for a disconnect ccw_device on the ccw bus rather than on the css
bus (was a typo in patch I did for the klist conversion).  A cast to an
embedding ccw_device from an embedded device in a struct subchannel will
lead us to oopses.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This used to be inline in include/asm-ppc64/unistd.h, but isn't
inline in the merged include/asm-powerpc/unistd.h, so we need a
definition here.
Signed-off-by: Paul Mackerras <paulus@samba.org>

These two files are now built in arch/powerpc/kernel instead of
arch/ppc64/kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>

This fixes up a variety of minor problems in compiling with ARCH=ppc
arising from using the merged versions of various header files.
A lot of the changes are just adding #include <asm/machdep.h> to
files that use ppc_md or smp_ops_t.

This also arranges for us to use semaphore.c, vecemu.c, vector.S and
fpu.S from arch/powerpc/kernel when compiling with ARCH=ppc.
Signed-off-by: Paul Mackerras <paulus@samba.org>

Now instead of having a ppc_md function, we just have a variable
which says whether to do the i8259 irq canonicalization or not,
and set that variable on the platforms that need that.  It looks
to me that radstone_ppc7d was trying to use irq canonicalization
for something else in a broken kind of way - it will need to be
fixed properly.
Signed-off-by: Paul Mackerras <paulus@samba.org>

A bunch of printks were left in arch/powerpc/kernel/setup_64.c from
when I was chasing a bug.  This removes them.
Signed-off-by: Paul Mackerras <paulus@samba.org>

Breakage noted by Al Viro.

It breaks non-PCI builds, it's probably better to have a more
direct implementation on sparc32, and which driver actually
needs this is still questionable.

We can resolve this in 2.6.15
Signed-off-by: David S. Miller <davem@davemloft.net>

Incorrect uart_write_wakeup() calls cause reference to a
NULL tty pointer in sunsab and sunzilog serial drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>

... since it isn't needed.
Signed-off-by: Paul Mackerras <paulus@samba.org>

Xmon itself isn't merged yet, though.
Signed-off-by: Paul Mackerras <paulus@samba.org>

Since we don't have an 83xx directory or a 83xx/Makefile, having
83xx in causes make clean to fail.
Signed-off-by: Paul Mackerras <paulus@samba.org>

Signed-off-by: Paul Mackerras <paulus@samba.org>