The subtraction of the two pointers is automatically scaled by the
size of the size of the object the pointers point to, so the division
by sizeof(*i2400m->barker) is incorrect.  This has been broken since
day one of the driver and is only debug, so remove the debug completely.

Also move && in condition to clean up a checkpatch warning.

Addresses-Coverity: ("Extra sizeof expression")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct spider_net_card {
	...
        struct spider_net_descr darray[0];
};

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.

So, replace the following form:

sizeof(struct spider_net_card) + (tx_descriptors + rx_descriptors) * sizeof(struct spider_net_descr)

with:

struct_size(card, darray, tx_descriptors + rx_descriptors)

Notice that, in this case, variable alloc_size is not necessary, hence it
is removed.

Building: allmodconfig powerpc.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: add support for RTL8125

This series adds support for the 2.5Gbps chip RTl8125. It can be found
on PCIe network cards, and on an increasing number of consumer gaming
mainboards. Series is partially based on the r8125 vendor driver.
Tested with a Delock 89531 PCIe card against a Netgear GS110MX
Multi-Gig switch.
Firmware isn't strictly needed, but on some systems there may be
compatibility issues w/o firmware. Firmware has been submitted to
linux-firmware.

v2:
- split first patch into 6 smaller ones to facilitate bisecting
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds EEE support for RTL8125 based on the vendor driver.
Supported is EEE for 100Mbps and 1Gbps. Realtek recommended to not yet
enable EEE for 2.5Gbps due to potential compatibility issues. Also
ethtool doesn't support yet controlling EEE for 2.5Gbps and 5Gbps.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds PHY initialization magic copied from the r8125 vendor
driver. In addition it supports loading the firmware for chip version
RTL_GIGA_MAC_VER_61.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for 2.5Gbps chip RTL8125, it's partially based on the
r8125 vendor driver. Tested with a Delock 89531 PCIe card against a
Netgear GS110MX Multi-Gig switch. Firmware isn't strictly needed,
but on some systems there may be compatibility issues w/o firmware.
Firmware has been submitted to linux-firmware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On RTL8125 this bit is always cleared after send. Therefore check for
tx_skb->skb being set what is functionally equivalent.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RTL8125 uses a different register number for IntrMask.
To net have side effects by reading a random register let's
use a register that is the same on all supported chip families.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RTL8125 doesn't support the same coalescing registers, therefore move
this initialization to the 8168/6169-specific init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For RTL8125 we will have to read the MAC address also from another
register range, therefore create a small helper.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend helper rtl_is_8168evl_up to properly work once we add
mac version numbers >51 for RTL8125.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RTL8125 uses a 32 bit interrupt mask even though only bits in the
lower 16 bits are used. Change interrupt mask size to u32 to be
prepared and reintroduce helper rtl_get_events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2019-08-22

Misc updates for mlx5e net device driver

1) Maxim and Tariq add the support for LAG TX port affinity distribution
When VF LAG is enabled, VFs netdevs will round-robin the TX affinity
of their tx queues among the different LAG ports.
2) Aya adds the support for ip-in-ip RSS.
3) Marina adds the support for ip-in-ip TX TSO and checksum offloads.
4) Moshe adds a device internal drop counter to mlx5 ethtool stats.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now mv88e6xxx does not enable its ports at setup itself and let
the DSA core handle this, unused ports are disabled without being
powered on first. While that is expected, the SERDES powering code
was assuming that a port was already set up before powering it down,
resulting in freeing an unused IRQ. The patch fixes this assumption.

Fixes: b759f528 ("net: dsa: mv88e6xxx: enable SERDES after setup")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a follow-up patch for commit 7a3007d2 ("net: dsa:
mv88e6xxx: fully support SERDES on Topaz family").

Since .port_set_cmode is only called from mv88e6xxx_port_setup_mac and
mv88e6xxx_phylink_mac_config, it is fine to keep this "make writable"
code private to the mv88e6341_port_set_cmode implementation, instead
of adding yet another operation to the switch info structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a follow-up patch for commit 17deaf5c ("net: dsa:
mv88e6xxx: create serdes_get_lane chip operation").

The .serdes_get_lane implementations access the CMODE of a port,
even though it is cached at the moment, it is safer to call them
after the mutex is locked, not before.

At the same time, check for an eventual error and return IRQ_DONE,
instead of blindly ignoring it.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: add some cleanups and optimizations

This patch-set includes cleanups, optimizations and bugfix for
the HNS3 ethernet controller driver.

[patch 01/12] adds code optimization for debugfs command "dump reg".

[patch 02/12] fixes magic number issues.

[patch 03/12] modifies some parameters about hclge_dbg_dump_tm_map().

[patch 04/12] removes some unused parameters.

[patch 05/12] refactors some logs to make them more readable.

[patch 06/12] makes some resusable codes into functions.

[patch 07/12] fixes some type errors.

[patch 08/12] reduces the waiting time for per TQP reset.

[patch 09/12] implements .process_hw_error for hns3 client.

[patch 10/12] adds phy selftest for HNS3 driver.

[patch 11/12] adds checking for reset interrupt status when reset fails.

[patch 12/12] prevents SSU loopback when running ethtool -t.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current loopback mode is to add 0x1F to the SMAC address
as the DMAC address and enable the promiscuous mode.
However, if the VF address is the same as the DMAC address,
the loopback test fails.

Loopback can be enabled in three places: SSU, MAC, and serdes.
By default, SSU loopback is enabled, so if the SMAC and the DMAC
are the same, the packets are looped back in the SSU. If SSU loopback
is disabled, packets can reach MAC even if SMAC is the same as DMAC.

Therefore, this patch disables the SSU loopback before the loopback
test. In this way, the SMAC and DMAC can be the same, and the
promiscuous mode does not need to be enabled. And this is not
valid in version 0x20.

This patch also uses a macro to replace 0x1F.

Fixes: c39c4d98 ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the reset interrupt will be cleared firstly, so when
reset fails, if interrupt status register has reset interrupt,
it means there is a new coming reset.

Fixes: 72e2fb07 ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the loopback test supports only mac selftest and serdes
selftest. This patch adds phy selftest.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When hardware or IMP get specified error it may need the client
to take some special operations.

This patch implements the hns3 client's process_hw_errorx.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch optimizes the waiting time for TQP reset.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes some incorrect type in assignment reported by sparse.
Those sparse warning as below:
- warning : restricted __le16 degrades to integer
- warning : cast from restricted __le32
- warning : expected restricted __le32
- warning : cast from restricted __be32
- warning : cast from restricted __be16
- warning : cast to restricted __le16
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In hclge_dcb.c, these pair of codes:
	hclge_notify_client(hdev, HNAE3_DOWN_CLIENT);
	hclge_notify_client(hdev, HNAE3_UNINIT_CLIENT);
and
	hclge_notify_client(hdev, HNAE3_INIT_CLIENT);
	hclge_notify_client(hdev, HNAE3_UP_CLIENT);
are called many times, so make them into a function.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To better identify abnormal conditions, this patch modifies or
adds some logs to show driver status more accurately.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch simplifies parameters of some functions by deleting
unused parameter.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch replaces kstrtouint()'s patameter base with 0 in the
hclge_dbg_dump_tm_mac(), which makes it more flexible. Also
uses a macro to replace string "dump tm map", since it has been
used multiple times.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch uses macro to replace some magic number.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For making the code more readable, this patch uses a array to
keep the information about the dumping register, and then uses
it to parse the parameter cmd_buf which passing into
hclge_dbg_dump_reg_cmd().

Also replaces parameter "base" of kstrtouint with 0 in the
hclge_dbg_dump_reg_common(), which makes it more flexible.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting with firmware version MC10.18.0, we have support for
L2 flow control. Asymmetrical configuration (Rx or Tx only) is
supported, but not pause frame autonegotioation.

Pause frame configuration is done via ethtool. By default, we start
with flow control enabled on both Rx and Tx. Changes are propagated
to hardware through firmware commands, using two flags (PAUSE,
ASYM_PAUSE) to specify Rx and Tx pause configuration, as follows:

PAUSE | ASYM_PAUSE | Rx pause | Tx pause
----------------------------------------
  0   |     0      | disabled | disabled
  0   |     1      | disabled | enabled
  1   |     0      | enabled  | enabled
  1   |     1      | enabled  | disabled

The hardware can automatically send pause frames when the number
of buffers in the pool goes below a predefined threshold. Due to
this, flow control is incompatible with Rx frame queue taildrop
(both mechanisms target the case when processing of ingress
frames can't keep up with the Rx rate; for large frames, the number
of buffers in the pool may never get low enough to trigger pause
frames as long as taildrop is enabled). So we set pause frame
generation and Rx FQ taildrop as mutually exclusive.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever a link state change occurs, we get notified and save
the new link settings in the device's private data. In ethtool
get_link_ksettings, use the stored state instead of interrogating
the firmware each time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

We only support fixed-link for now, so there is no point in
offering users the option to change link settings via ethtool.

Functionally there is no change, since firmware prevents us from
changing link parameters anyway.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Various updates

Patch #1 from Amit removes 56G speed support. The reasons for this are
detailed in the commit message.

Patch #2 from Shalom ensures that the hardware does not auto negotiate
the number of used lanes. For example, if a four lane port supports 100G
over both two and four lanes, it will not advertise the two lane link
mode.

Patch #3 bumps the firmware version supported by the driver.

Patch #4 from Petr adds ethtool counters to help debug the internal PTP
implementation in mlxsw. I copied Richard on this patch in case he has
comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On Spectrum-1, timestamped PTP packets and the corresponding timestamps need to
be kept in caches until both are available, at which point they are matched up
and packets forwarded as appropriate. However, not all packets will ever see
their timestamp, and not all timestamps will ever see their packet. It is
necessary to dispose of such abandoned entries, so a garbage collector was
introduced in commit 5d23e415 ("mlxsw: spectrum: PTP: Garbage-collect
unmatched entries").

If these GC events happen often, it is a sign of a problem. However because this
whole mechanism is taking place behind the scenes, there is no direct way to
determine whether garbage collection took place.

Therefore to fix this, on Spectrum-1 only, expose four artificial ethtool
counters for the GC events: GCd timestamps and packets, in TX and RX directions.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new version supports extended error reporting from firmware via a
new TLV in the EMAD packet. Similar to netlink extended ack.

It also fixes an issue in the PCI code that can result in false AER
errors under high Tx rate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After 50G-1-lane and 100G-2-lanes link modes were introduced, the driver
is facing situations in which the hardware auto negotiates not only on
speed and type, but also on number of lanes.

Prevent auto negotiation on number of lanes by allowing only port speeds
that can be supported on a given port according to its width.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 275e928f ("mlxsw: spectrum: Prevent force of 56G") prevented
the driver from setting a speed of 56G when auto-negotiation is off.
This is the only speed supported by mlxsw that cannot be set when
auto-negotiation is off, which makes it difficult to write generic
tests.

Further, the speed is not supported by newer ASICs such as Spectrum-2
and to the best of our knowledge it is not used by current users.

Therefore, remove 56G support from mlxsw.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some ethernet drivers may call phy_start() and phy_stop() from
ndo_open() and ndo_close() respectively.

When network cable is unconnected, and operate like below:
step 1: ifconfig ethX up -> ndo_open -> phy_start ->start
autoneg, and phy is no link.
step 2: ifconfig ethX down -> ndo_close -> phy_stop -> just stop
phy state machine.

This patch forces phy suspend even phydev->link is off.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-08-26

This series contains updates to ice driver only.

Usha fixes the statistics reported on 4 port NICs which were reporting
the incorrect statistics due to using the incorrect port identifier.

Victor fixes an issue when trying to traverse to the first node of a
requested layer by adding a sibling head pointer for each layer per
traffic class.

Anirudh cleans up the locking and logic for enabling and disabling
VSI's to make it more consistent.  Updates the driver to do dynamic
allocation of queue management bitmaps and arrays, rather than
statically allocating them which consumes more memory than required.
Refactor the logic in ice_ena_msix_range() for clarity and add
additional checks for when requested resources exceed what is available.

Jesse updates the debugging print statements to make it more useful when
dealing with link and PHY related issues.

Krzysztof adds a local variable to the VSI rebuild path to improve
readability.

Akeem limits the reporting of MDD events from VFs so that the kernel
log is not clogged up with MDD events which are duplicate or potentially
false positives.  Fixed a reset issue that would result in the system
getting into a state that could only be resolved by a reboot by
testing if the VF is in a disabled state during a reset.

Michal adds a check to avoid trying to access memory that has not be
allocated by checking the number of queue pairs.

Jake fixes a static analysis warning due to a cast of a u8 to unsigned
long, so just update ice_is_tc_ena() to take a unsigned long so that a
cast is not necessary.

Colin Ian King fixes a potential infinite loop where a u8 is being
compared to an int.

Maciej refactors the queue handling functions that work on queue arrays
so that the logic can be done for a single queue.

Paul adds support for VFs to enable and disable single queues.

Henry fixed the order of operations in ice_remove() which was trying to
use adminq operations that were already disabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>