platform_device pdev can be NULL if CONFIG_MMC_OMAP_HS is not set.
Add check for NULL pointer. while at it move the duplicated functions
to omap4-common.c

Fixes the following boot crash seen with omap4sdp and omap4panda
when MMC is disabled.

Unable to handle kernel NULL pointer dereference at virtual address 0000008c
pgd = c0004000
[0000008c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0    Not tainted  (3.4.0-rc1-05971-ga4dfa82 #4)
PC is at omap_4430sdp_init+0x184/0x410
LR is at device_add+0x1a0/0x664
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

SX1 board requirese i2c, so select it in Kconfig, otherwise I have the
following build error:

arch/arm/mach-omap1/board-sx1.c: In function 'sx1_i2c_write_byte':
arch/arm/mach-omap1/board-sx1.c:58:2: error: implicit declaration of function 'i2c_get_adapter' [-Werror=implicit-function-declaration]
arch/arm/mach-omap1/board-sx1.c:58:7: warning: assignment makes pointer from integer without a cast [enabled by default]
arch/arm/mach-omap1/board-sx1.c:67:2: error: implicit declaration of function 'i2c_transfer' [-Werror=implicit-function-declaration]
arch/arm/mach-omap1/board-sx1.c:68:2: error: implicit declaration of function 'i2c_put_adapter' [-Werror=implicit-function-declaration]
arch/arm/mach-omap1/board-sx1.c: In function 'sx1_i2c_read_byte':
arch/arm/mach-omap1/board-sx1.c:82:7: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
make[1]: *** [arch/arm/mach-omap1/board-sx1.o] Error 1
make: *** [arch/arm/mach-omap1] Error 2
make: *** Waiting for unfinished jobs....
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull x86 fixes form Peter Anvin

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  intel_mid_powerbtn: mark irq as IRQF_NO_SUSPEND
  arch/x86/platform/geode/net5501.c: change active_low to 0 for LED driver
  x86, relocs: Remove an unused variable
  asm-generic: Use __BITS_PER_LONG in statfs.h
  x86/amd: Re-enable CPU topology extensions in case BIOS has disabled it

Pull btrfs fixes from Chris Mason:
 "The big ones here are a memory leak we introduced in rc1, and a
  scheduling while atomic if the transid on disk doesn't match the
  transid we expected.  This happens for corrupt blocks, or out of date
  disks.

  It also fixes up the ioctl definition for our ioctl to resolve logical
  inode numbers.  The __u32 was a merging error and doesn't match what
  we ship in the progs."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: avoid sleeping in verify_parent_transid while atomic
  Btrfs: fix crash in scrub repair code when device is missing
  btrfs: Fix mismatching struct members in ioctl.h
  Btrfs: fix page leak when allocing extent buffers
  Btrfs: Add properly locking around add_root_to_dirty_list

Setting TIF_IA32 in load_aout_binary() used to be enough; these days
TASK_SIZE is controlled by TIF_ADDR32 and that one doesn't get set
there.  Switch to use of set_personality_ia32()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

verify_parent_transid needs to lock the extent range to make
sure no IO is underway, and so it can safely clear the
uptodate bits if our checks fail.

But, a few callers are using it with spinlocks held.  Most
of the time, the generation numbers are going to match, and
we don't want to switch to a blocking lock just for the error
case.  This adds an atomic flag to verify_parent_transid,
and changes it to return EAGAIN if it needs to block to
properly verifiy things.
Signed-off-by: Chris Mason <chris.mason@oracle.com>

Pull alpha fixes from Matt Turner:
 "My alpha tree is back up (after taking quite some time to get my GPG
  key signed).  It contains just some simple fixes."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
  alpha: silence 'const' warning in sys_marvel.c
  alpha: include module.h to fix modpost on Tsunami
  alpha: properly define get/set_rtc_time on Marvel/SMP
  alpha: VGA_HOSE depends on VGA_CONSOLE

The test in pdc_console_tty_close '!tty->count' was always wrong
because tty->count is decremented after tty->ops->close is called and
thus can never be zero. Hence the 'then' branch was never executed and
the timer never deleted.

This did not matter until commit 5dd5bc40 ("TTY: pdc_cons, use
tty_port").  There we needed to set TTY in tty_port to NULL, but this
never happened due to the bug above.

So change the test to really trigger at the last close by changing the
condition to 'tty->count == 1'.

Well, the driver should not touch tty->count at all.  It should use
tty_port->count and count open count there itself.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-tested-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sound sound fixes from Takashi Iwai:
 "As good as nothing exciting here; just a few trivial fixes for various
  ASoC stuff."

* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: omap-pcm: Free dma buffers in case of error.
  ASoC: s3c2412-i2s: Fix dai registration
  ASoC: wm8350: Don't use locally allocated codec struct
  ASoC: tlv312aic23: unbreak resume
  ASoC: bf5xx-ssm2602: Set DAI format
  ASoC: core: check of_property_count_strings failure
  ASoC: dt: sgtl5000.txt: Add description for 'reg' field
  ASoC: wm_hubs: Make sure we don't disable differential line outputs

Pull an ACPI patch from Len Brown:
 "It fixes a D3 issue new in 3.4-rc1."

By Lin Ming via Len Brown:
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  ACPI: Fix D3hot v D3cold confusion

Currently, we'll try mounting any device who's major device number is
UNNAMED_MAJOR as NFS root.  This would happen for non-NFS devices as
well (such as 9p devices) but it wouldn't cause any issues since
mounting the device as NFS would fail quickly and the code proceeded to
doing the proper mount:

       [  101.522716] VFS: Unable to mount root fs via NFS, trying floppy.
       [  101.534499] VFS: Mounted root (9p filesystem) on device 0:18.

Commit 6829a048102a ("NFS: Retry mounting NFSROOT") introduced retries
when mounting NFS root, which means that now we don't immediately fail
and instead it takes an additional 90+ seconds until we stop retrying,
which has revealed the issue this patch fixes.

This meant that it would take an additional 90 seconds to boot when
we're not using a device type which gets detected in order before NFS.

This patch modifies the NFS type check to require device type to be
'Root_NFS' instead of requiring the device to have an UNNAMED_MAJOR
major.  This makes boot process cleaner since we now won't go through
the NFS mounting code at all when the device isn't an NFS root
("/dev/nfs").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ASoC: Updates for 3.4

Nothing terribly exciting here, a bunch of small and simple fixes
scattered around the place.

Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.

After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.

ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot)  If these resources are all ON,
then the state is D3hot.  If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.

This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Commit ec81aecb ("hfs: fix a potential buffer overflow") fixed a few
potential buffer overflows in the hfs filesystem.  But as Timo Warns
pointed out, these changes also need to be made on the hfsplus
filesystem as well.
Reported-by: Timo Warns <warns@pre-sense.de>
Acked-by: WANG Cong <amwang@redhat.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Miklos Szeredi <mszeredi@suse.cz>
Cc: Sage Weil <sage@newdream.net>
Cc: Eugene Teo <eteo@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Dave Anderson <anderson@redhat.com>
Cc: stable <stable@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fix from Thomas Gleixner.

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rtc: Fix possible null pointer dereference in rtc-mpc5121.c

Pull CIFS fixes from Steve French.

* git://git.samba.org/sfrench/cifs-2.6:
  fs/cifs: fix parsing of dfs referrals
  cifs: make sure we ignore the credentials= and cred= options
  [CIFS] Update cifs version to 1.78
  cifs - check S_AUTOMOUNT in revalidate
  cifs: add missing initialization of server->req_lock
  cifs: don't cap ra_pages at the same level as default_backing_dev_info
  CIFS: Fix indentation in cifs_show_options

Remove myself as cpufreq maintainer.
x86 driver changes can go through the regular x86/ACPI trees.
ARM driver changes through the ARM trees.
cpufreq core changes are rare these days, and can just go to lkml/direct.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The normal read_seqcount_begin() function will wait for any current
writers to exit their critical region by looping until the sequence
count is even.

That "wait for sequence count to stabilize" is the right thing to do if
the read-locker will just retry the whole operation on contention: no
point in doing a potentially expensive reader sequence if we know at the
beginning that we'll just end up re-doing it all.

HOWEVER.  Some users don't actually retry the operation, but instead
will abort and do the operation with proper locking.  So the sequence
count case may be the optimistic quick case, but in the presense of
writers you may want to do full locking in order to guarantee forward
progress.  The prime example of this would be the RCU name lookup.

And in that case, you may well be better off without the "retry early",
and are in a rush to instead get to the failure handling.  Thus this
"raw" interface that just returns the sequence number without testing it
- it just forces the low bit to zero so that read_seqcount_retry() will
always fail such a "active concurrent writer" scenario.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We really need to use a ACCESS_ONCE() on the sequence value read in
__read_seqcount_begin(), because otherwise the compiler might end up
reloading the value in between the test and the return of it.  As a
result, it might end up returning an odd value (which means that a write
is in progress).

If the reader is then fast enough that that odd value is still the
current one when the read_seqcount_retry() is done, we might end up with
a "successful" read sequence, even despite the concurrent write being
active.

In practice this probably never really happens - there just isn't
anything else going on around the read of the sequence count, and the
common case is that we end up having a read barrier immediately
afterwards.

So the code sequence in which gcc might decide to reaload from memory is
small, and there's no reason to believe it would ever actually do the
reload.  But if the compiler ever were to decide to do so, it would be
incredibly annoying to debug.  Let's just make sure.

Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

So that the power button still wakes up the platform.
Signed-off-by: Pierre Tardy <pierre.tardy@intel.com>
Link: http://lkml.kernel.org/r/20120504210244.F2EA5A018B@akpm.mtv.corp.google.comTested-by: Kangkai Yin <kangkai.yin@intel.com>
Tested-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

It seems that there was an error with the active_low = 1 for the
LED, since it should be set to 0 (meaning that active is high,
since 0 is false, hence the confusion.

The wiki article about it confuses it, since it contradicts itself,
regarding what turns on the LED.

I have tested 3.4-rc2 on my net5501 with this patch, and it makes the LED
behave correctly, where "none" turns it off, and "default-on" turns it on,
when echoed onto the trigger "file" in /sys/class/leds.
Signed-off-by: Bjarke Istrup Pedersen <gurligebis@gentoo.org>
Link: http://lkml.kernel.org/r/20120504210146.62186A018B@akpm.mtv.corp.google.com
Cc: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Fix that when scrub tries to repair an I/O or checksum error and one of
the devices containing the mirror is missing, it crashes in bio_add_page
because the bdev is a NULL pointer for missing devices.
Reported-by: Marco L. Crociani <marco.crociani@gmail.com>
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

Fix the size members of btrfs_ioctl_ino_path_args and
btrfs_ioctl_logical_ino_args. The user space btrfs-progs utilities used
__u64 and the kernel headers used __u32 before.
Signed-off-by: Alexander Block <ablock84@googlemail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

If we happen to alloc a extent buffer and then alloc a page and notice that
page is already attached to an extent buffer, we will only unlock it and
free our existing eb.  Any pages currently attached to that eb will be
properly freed, but we don't do the page_cache_release() on the page where
we noticed the other extent buffer which can cause us to leak pages and I
hope cause the weird issues we've been seeing in this area.  Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

add_root_to_dirty_list happens once at the very beginning of the
transaction, but it is still racey.
Signed-off-by: Chris Mason <chris.mason@oracle.com>

Pull drm fixes from Dave Airlie:
 "Some minor fixes from Intel and a radeon fix.

  I have the nouveau fix for the i2c regression queued for next week,
  its mostly a revert and seems to work on the system it was originally
  introduced for thanks to some i2c core changes."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: clarify and extend wb setup on APUs and NI+ asics
  drm/i915: enable dip before writing data on gen4
  fixing dmi match for hp t5745 and hp st5747 thin client
  drm/i915: Only enable IPS polling for gen5
  drm/i915: Do not read non-existent DPLL registers on PCH hardware

Pull one small fix for md/bitmaps from NeilBrown:
 "This fixes a regression that was introduced in the merge window."

* tag 'md-3.4-fixes' of git://neil.brown.name/md:
  md/bitmap: fix calculation of 'chunks' - missing shift.

Jana Saout confirmed that this fixes the page faults he saw.

His problem was triggered by ocfs2 and autofs symlink lookups, where the
symlink allocation was at the end of a page.  But the deeper reason
seems to be the use of Xen-PV, which is what then causes him to have all
these unmapped pages, which is what then makes it a problem when the
unaligned word-at-a-time code fetches data past the end of a page.

* fix-unmapped-word-at-a-time:
  vfs: make word-at-a-time accesses handle a non-existing page

Signed-off-by: Oleg Matcovschi <oleg.matcovschi@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

Use family rather than DCE check for clarity, also always use
wb on APUs, there will never be AGP variants.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

commit 61a0d80c "md/bitmap: discard CHUNK_BLOCK_SHIFT macro"
replaced CHUNK_BLOCK_RATIO() by the same text that was
replacing CHUNK_BLOCK_SHIFT() - which is clearly wrong.

The result is that 'chunks' is often too small by 1,
which can sometimes result in a crash (not sure how).

So use the correct replacement, and get rid of CHUNK_BLOCK_RATIO
which is no longe used.
Reported-by: Karl Newman <siliconfiend@gmail.com>
Tested-by: Karl Newman <siliconfiend@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

The problem was that the first referral was parsed more than once
and so the caller tried the same referrals multiple times.

The problem was introduced partly by commit
066ce689,
where 'ref += le16_to_cpu(ref->Size);' got lost,
but that was also wrong...

Cc: <stable@vger.kernel.org>
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Tested-by: Björn Jacke <bj@sernet.de>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

Pull second set of MFD fixes from Samuel Ortiz:
 "This time we only have a one liner fixing an omap-usb build error."

* tag 'mfd-for-linus-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: Fix build breakage in omap-usb-host.c

* efi-vars:
  efivars: Improve variable validation

Ben Hutchings pointed out that the validation in efivars was inadequate -
most obviously, an entry with size 0 would server as a DoS against the
kernel. Improve this based on his suggestions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull libata fixes from Jeff Garzik:

1) Fix regression that could cause a misdiagnosis, which in turn could
   lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug
   and suspend/resume is involved.

2) Fix a regression that led to ata%d controller ids being numbered one
   larger than in <= 3.4-rc3 (oh, the horror!).  Controller ids should now be
   as expected.

3) add some DT, PCI id's

4) ata/pata_arasan_cf: minor cpp fixing/cleaning

* tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ata: ahci_platform: Add synopsys ahci controller in DT's compatible list
  ata/pata_arasan_cf: Move arasan_cf_pm_ops out of #ifdef, #endif macros
  libata: init ata_print_id to 0
  ahci: Detect Marvell 88SE9172 SATA controller
  libata: skip old error history when counting probe trials

Pull i2c embedded fixes from Wolfram Sang:
 "Here are some typical i2c driver bugfixes for 3.4.  Missed clock
  handling, improper timeout fixes, hardware wrokarounds...  All
  patches have been in linux-next for a few days, too."

* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
  i2c: mxs: disable QUEUE when sending is done
  i2c: mxs: handle spurious interrupt
  i2c-eg20t: Modify MODULE_AUTHOR's email address
  i2c-eg20t: change timeout value 50msec to 1000msec
  i2c: tegra: Add delay before resetting the controller after NACK
  i2c: pnx: Disable clk in suspend