The DWC3 USB driver is not a clock provider, and just needs to call
of_clk_get_parent_count().

Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

If dwc->dev in device mode already runtime suspended, don't do it again
for system suspend.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The dwc3 core binding specifies one reset.

However some variants of the hardware may have more. Previously
this was handled by using the dwc3-of-simple glue driver, but
that resulted in a proliferation of bindings for for every
variant, when the only difference was the clocks and resets
lists.

So this patch reworks the reading of the resets to fetch all the
resets specified in the dts together.

This patch was recommended by Rob Herring <robh@kernel.org>
as an alternative to creating multiple bindings for each variant
of hardware.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The dwc3 core binding specifies three clocks:
  ref, bus_early, and suspend

which are all controlled in the driver together.

However some variants of the hardware my not have all three
clks, or some may have more. Usually this was handled by using
the dwc3-of-simple glue driver, but that resulted in a
proliferation of bindings for for every variant, when the only
difference was the clocks and resets lists.

So this patch reworks the reading of the clks from the dts to
use devm_clk_bulk_get_all() will will fetch all the clocks
specified in the dts together.

This patch was recommended by Rob Herring <robh@kernel.org>
as an alternative to creating multiple bindings for each variant
of hardware.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Rather then adding another device specific binding to support
hikey960, Rob Herring suggested we expand the current dwc3
binding to allow for variable numbers of clocks and resets.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Support the new role-switch-default-mode binding for configuring
the default role the controller assumes as when the usb role is
USB_ROLE_NONE

This patch was split out from a larger patch originally by
Yu Chen <chenyu56@huawei.com>

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Add binding to configure the default role the controller
assumes is host mode when the usb role is USB_ROLE_NONE.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The Type-C drivers use USB role switch API to inform the
system about the negotiated data role, so registering a role
switch in the DRD code in order to support platforms with
USB Type-C connectors.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

In certain circumstances, the XHCI SuperSpeed instance in park mode
can fail to recover, thus on Amlogic G12A/G12B/SM1 SoCs when there is high
load on the single XHCI SuperSpeed instance, the controller can crash like:
 xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
 xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
 xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
 xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
 hub 2-1.1:1.0: hub_ext_port_status failed (err = -22)
 xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
 usb 2-1.1-port1: cannot reset (err = -22)

Setting the PARKMODE_DISABLE_SS bit in the DWC3_USB3_GUCTL1 mitigates
the issue. The bit is described as :
"When this bit is set to '1' all SS bus instances in park mode are disabled"

Synopsys explains:
The GUCTL1.PARKMODE_DISABLE_SS is only available in
dwc_usb3 controller running in host mode.
This should not be set for other IPs.
This can be disabled by default based on IP, but I recommend to have a
property to enable this feature for devices that need this.

CC: Dongjin Kim <tobetter@gmail.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

This patch updates the documentation with the information related
to the quirks that needs to be added for disabling all SuperSpeed XHCI
instances in park mode.

Cc: Dongjin Kim <tobetter@gmail.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

When skipping TRBs, we need to account for wrapping around the ring
buffer and not modifying some invalid TRBs. Without this fix, dwc3 won't
be able to check for available TRBs.

Cc: stable <stable@vger.kernel.org>
Fixes: 7746a8df ("usb: dwc3: gadget: extract dwc3_gadget_ep_skip_trbs()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

We track END_TRANSFER command completion. Don't clear transfer
started/ended flag prematurely. Otherwise, we'd run into the problem
with restarting transfer before END_TRANSFER command finishes.

Fixes: 6d8a0196 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The main comment in the file mistakenly marked with kernel doc annotation
which makes the parser unhappy:

.../dwc3/host.c:16: warning: Function parameter or member 'dwc' not described in 'dwc3_host_get_irq'

Drop kernel doc annotation from host.c module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The ACPI companion of the adapter has to be set for xHCI controller
code to read and attach the ports described in the ACPI table.
Use ACPI_COMPANION_SET macro to set this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Exynos5422 DWC3 module support two clk USBD300 and SCLK_USBD300
so add missing code to enable/disable code and suspend clk, for this
add a new compatible samsung,exynos5420-dwusb3 to help configure
dwc3 code and dwc3 suspend clock. Suspend clock controls the PHY power
change from P0 to P1/P2/P3 during U0 to U1/U2/U3 transition.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Clang warns:

../drivers/usb/dwc3/dwc3-meson-g12a.c:421:6: warning: variable 'ret' is
used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
        if (priv->otg_mode == USB_DR_MODE_OTG) {
            ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/usb/dwc3/dwc3-meson-g12a.c:455:9: note: uninitialized use
occurs here
        return ret;
               ^~~
../drivers/usb/dwc3/dwc3-meson-g12a.c:421:2: note: remove the 'if' if
its condition is always true
        if (priv->otg_mode == USB_DR_MODE_OTG) {
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/usb/dwc3/dwc3-meson-g12a.c:415:9: note: initialize the
variable 'ret' to silence this warning
        int ret, irq;
               ^
                = 0
1 warning generated.

It is not wrong, ret is only used when that if statement is true. Just
directly return 0 at the end to avoid this.

Fixes: 729149c53f04 ("usb: dwc3: Add Amlogic A1 DWC3 glue")
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://groups.google.com/d/msg/clang-built-linux/w5iBENco_m4/PPuXreAxBQAJ
Link: https://github.com/ClangBuiltLinux/linux/issues/869Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Pointer trb being assigned with a value that is never read, it is
assigned a new value later on. The assignment is redundant and
can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Variable status is being assigned with a value that is never read, it is
assigned a new value immediately afterwards. The assignment is redundant
and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

This patch introduces a new parameter to activate external ID pin and valid
vbus level detection, required on STM32MP15 SoC to support dual role,
either in HS or FS.
The STM32MP15 SoC uses the GGPIO register to enable the level detection.
The level detector requires to be powered.
Also adds the params structures for STM32MP15 OTG HS and STM32MP1 OTG FS.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Adds support for Amlogic A1 USB Control Glue HW.

The Amlogic A1 SoC Family embeds 1 USB Controllers:
- a DWC3 IP configured as Host for USB2 and USB3

A glue connects the controllers to the USB2 PHY of A1 SoC.
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The Amlogic A1 SoC Family embeds 1 USB Controllers:
 - a DWC3 IP configured as Host for USB2 and USB3

A glue connects the controllers to the USB2 PHY of A1 SoC.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The MAX3420 is USB2.0 only, UDC-over-SPI controller. This driver
also supports the peripheral mode of MAX3421.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Add YAML dt bindings for Maxim MAX3420 UDC controller.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

By printing enqueue/dequeue pointers, we can make sure that our TRB
handling is correct. We've had a recent situation where we were not
always dequeueing all TRBs in an SG list and this helped figure out
what the problem was.
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Pull ARM SoC fixes from Olof Johansson:
 "We've been accruing these for a couple of weeks, so the batch is a bit
  bigger than usual.

  Largest delta is due to a led-bl driver that is added -- there was a
  miscommunication before the merge window and the driver didn't make it
  in. Due to this, the platforms needing it regressed. At this point, it
  seemed easier to add the new driver than unwind the changes.

  Besides that, there are a handful of various fixes:

   - AMD tee memory leak fix

   - A handful of fixlets for i.MX SCU communication

   - A few maintainers woke up and realized DEBUG_FS had been missing
     for a while, so a few updates of that.

  ... and the usual collection of smaller fixes to various platforms"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (37 commits)
  ARM: socfpga_defconfig: Add back DEBUG_FS
  arm64: dts: socfpga: agilex: Fix gmac compatible
  ARM: bcm2835_defconfig: Explicitly restore CONFIG_DEBUG_FS
  arm64: dts: meson: fix gxm-khadas-vim2 wifi
  arm64: dts: meson-sm1-sei610: add missing interrupt-names
  ARM: meson: Drop unneeded select of COMMON_CLK
  ARM: dts: bcm2711: Add pcie0 alias
  ARM: dts: bcm283x: Add missing properties to the PWR LED
  tee: amdtee: fix memory leak in amdtee_open_session()
  ARM: OMAP2+: Fix compile if CONFIG_HAVE_ARM_SMCCC is not set
  arm: dts: dra76x: Fix mmc3 max-frequency
  ARM: dts: dra7: Add "dma-ranges" property to PCIe RC DT nodes
  bus: ti-sysc: Fix 1-wire reset quirk
  ARM: dts: r8a7779: Remove deprecated "renesas, rcar-sata" compatible value
  soc: imx-scu: Align imx sc msg structs to 4
  firmware: imx: Align imx_sc_msg_req_cpu_start to 4
  firmware: imx: scu-pd: Align imx sc msg structs to 4
  firmware: imx: misc: Align imx sc msg structs to 4
  firmware: imx: scu: Ensure sequential TX
  ARM: dts: imx7-colibri: Fix frequency for sd/mmc
  ...

Pull EDAC fix from Borislav Petkov:
 "Error reporting fix for synopsys_edac: do not overwrite partial
  decoded error message (Sherry Sun)"

* tag 'edac_urgent-2020-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  EDAC/synopsys: Do not print an error with back-to-back snprintf() calls

Pull char/misc fixes from Greg KH:
 "Here are four small char/misc driver fixes for reported issues for
  5.6-rc5.

  These fixes are:

   - binder fix for a potential use-after-free problem found (took two
     tries to get it right)

   - interconnect core fix

   - altera-stapl driver fix

  All four of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  binder: prevent UAF for binderfs devices II
  interconnect: Handle memory allocation errors
  altera-stapl: altera_get_note: prevent write beyond end of 'key'
  binder: prevent UAF for binderfs devices

Pull driver core and debugfs fixes from Greg KH:
 "Here are four small driver core / debugfs patches for 5.6-rc3:

   - debugfs api cleanup now that all debugfs_create_regset32() callers
     have been fixed up. This was waiting until after the -rc1 merge as
     these fixes came in through different trees

   - driver core sync state fixes based on reports of minor issues found
     in the feature

  All of these have been in linux-next with no reported issues"

* tag 'driver-core-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core: Skip unnecessary work when device doesn't have sync_state()
  driver core: Add dev_has_sync_state()
  driver core: Call sync_state() even if supplier has no consumers
  debugfs: remove return value of debugfs_create_regset32()

Pull tty/serial fixes from Greg KH:
 "Here are some small tty/serial fixes for 5.6-rc5

  Just some small serial driver fixes, and a vt core fixup, full details
  are:

   - vt fixes for issues found by syzbot

   - serdev fix for Apple boxes

   - fsl_lpuart serial driver fixes

   - MAINTAINER update for incorrect serial files

   - new device ids for 8250_exar driver

   - mvebu-uart fix

  All of these have been in linux-next with no reported issues"

* tag 'tty-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: fsl_lpuart: free IDs allocated by IDA
  Revert "tty: serial: fsl_lpuart: drop EARLYCON_DECLARE"
  serdev: Fix detection of UART devices on Apple machines.
  MAINTAINERS: Add missed files related to Synopsys DesignWare UART
  serial: 8250_exar: add support for ACCES cards
  tty:serial:mvebu-uart:fix a wrong return
  vt: selection, push sel_lock up
  vt: selection, push console lock down

Pull USB/PHY fixes from Greg KH:
 "Here are some small USB and PHY driver fixes for reported issues for
  5.6-rc5.

  Included in here are:

   - phy driver fixes

   - new USB quirks

   - USB cdns3 gadget driver fixes

   - USB hub core fixes

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: dwc3: gadget: Update chain bit correctly when using sg list
  usb: core: port: do error out if usb_autopm_get_interface() fails
  usb: core: hub: do error out if usb_autopm_get_interface() fails
  usb: core: hub: fix unhandled return by employing a void function
  usb: storage: Add quirk for Samsung Fit flash
  usb: quirks: add NO_LPM quirk for Logitech Screen Share
  usb: usb251xb: fix regulator probe and error handling
  phy: allwinner: Fix GENMASK misuse
  usb: cdns3: gadget: toggle cycle bit before reset endpoint
  usb: cdns3: gadget: link trb should point to next request
  phy: mapphone-mdm6600: Fix timeouts by adding wake-up handling
  phy: brcm-sata: Correct MDIO operations for 40nm platforms
  phy: ti: gmii-sel: do not fail in case of gmii
  phy: ti: gmii-sel: fix set of copy-paste errors
  phy: core: Fix phy_get() to not return error on link creation failure
  phy: mapphone-mdm6600: Fix write timeouts with shorter GPIO toggle interval

Pull rdma fixes from Jason Gunthorpe:
 "Nothing particularly exciting, some small ODP regressions from the mmu
  notifier rework, another bunch of syzkaller fixes, and a bug fix for a
  botched syzkaller fix in the first rc pull request.

   - Fix busted syzkaller fix in 'get_new_pps' - this turned out to
     crash on certain HW configurations

   - Bug fixes for various missed things in error unwinds

   - Add a missing rcu_read_lock annotation in hfi/qib

   - Fix two ODP related regressions from the recent mmu notifier
     changes

   - Several more syzkaller bugs in siw, RDMA netlink, verbs and iwcm

   - Revert an old patch in CMA as it is now shown to not be allocating
     port numbers properly"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/iwcm: Fix iwcm work deallocation
  RDMA/siw: Fix failure handling during device creation
  RDMA/nldev: Fix crash when set a QP to a new counter but QPN is missing
  RDMA/odp: Ensure the mm is still alive before creating an implicit child
  RDMA/core: Fix protection fault in ib_mr_pool_destroy
  IB/mlx5: Fix implicit ODP race
  IB/hfi1, qib: Ensure RCU is locked when accessing list
  RDMA/core: Fix pkey and port assignment in get_new_pps
  RMDA/cm: Fix missing ib_cm_destroy_id() in ib_cm_insert_listen()
  RDMA/rw: Fix error flow during RDMA context initialization
  RDMA/core: Fix use of logical OR in get_new_pps
  Revert "RDMA/cma: Simplify rdma_resolve_addr() error flow"

Pull io_uring fixes from Jens Axboe:
 "Here are a few io_uring fixes that should go into this release. This
  contains:

   - Removal of (now) unused io_wq_flush() and associated flag (Pavel)

   - Fix cancelation lockup with linked timeouts (Pavel)

   - Fix for potential use-after-free when freeing percpu ref for fixed
     file sets

   - io-wq cancelation fixups (Pavel)"

* tag 'io_uring-5.6-2020-03-07' of git://git.kernel.dk/linux-block:
  io_uring: fix lockup with timeouts
  io_uring: free fixed_file_data after RCU grace period
  io-wq: remove io_wq_flush and IO_WQ_WORK_INTERNAL
  io-wq: fix IO_WQ_WORK_NO_CANCEL cancellation

Pull block fixes from Jens Axboe:
 "Here are a few fixes that should go into this release. This contains:

   - Revert of a bad bcache patch from this merge window

   - Removed unused function (Daniel)

   - Fixup for the blktrace fix from Jan from this release (Cengiz)

   - Fix of deeper level bfqq overwrite in BFQ (Carlo)"

* tag 'block-5.6-2020-03-07' of git://git.kernel.dk/linux-block:
  block, bfq: fix overwrite of bfq_group pointer in bfq_find_set_group()
  blktrace: fix dereference after null check
  Revert "bcache: ignore pending signals when creating gc and allocator thread"
  block: Remove used kblockd_schedule_work_on()

Pull media fixes from Mauro Carvalho Chehab:

 - a fix for the media controller links in both hantro driver and in
   v4l2-mem2mem core

 - some fixes for the pulse8-cec driver

 - vicodec: handle alpha channel for RGB32 formats, as it may be used

 - mc-entity.c: fix handling of pad flags

* tag 'media/v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  media: hantro: Fix broken media controller links
  media: mc-entity.c: use & to check pad flags, not ==
  media: v4l2-mem2mem.c: fix broken links
  media: vicodec: process all 4 components for RGB32 formats
  media: pulse8-cec: close serio in disconnect, not adap_free
  media: pulse8-cec: INIT_DELAYED_WORK was called too late

There is a recipe to deadlock the kernel: submit a timeout sqe with a
linked_timeout (e.g.  test_single_link_timeout_ception() from liburing),
and SIGKILL the process.

Then, io_kill_timeouts() takes @ctx->completion_lock, but the timeout
isn't flagged with REQ_F_COMP_LOCKED, and will try to double grab it
during io_put_free() to cancel the linked timeout. Probably, the same
can happen with another io_kill_timeout() call site, that is
io_commit_cqring().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull s390 fixes from Vasily Gorbik:

 - Fix panic in gup_fast on large pud by providing an implementation of
   pud_write. This has been overlooked during migration to common gup
   code.

 - Fix unexpected write combining on PCI stores.

* tag 's390-5.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/pci: Fix unexpected write combine on resource
  s390/mm: fix panic in gup_fast on large pud

Pull powerpc fixes from Michael Ellerman:
 "Some more powerpc fixes for 5.6:

   - One fix for a recent regression to our breakpoint/watchpoint code.

   - Another fix for our KUAP support, this time a missing annotation in
     a rarely used path in signal handling.

   - A fix for our handling of a CPU feature that effects the PMU, when
     booting guests in some configurations.

   - A minor fix to our linker script to explicitly include the .BTF
     section.

  Thanks to: Christophe Leroy, Desnes A. Nunes do Rosario, Leonardo
  Bras, Naveen N. Rao, Ravi Bangoria, Stefan Berger"

* tag 'powerpc-5.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/mm: Fix missing KUAP disable in flush_coherent_icache()
  powerpc: fix hardware PMU exception bug on PowerVM compatibility mode systems
  powerpc: Include .BTF section
  powerpc/watchpoint: Don't call dar_within_range() for Book3S

Pull xen fixes from Juergen Gross:
 "Four fixes and a small cleanup patch:

   - two fixes by Dongli Zhang fixing races in the xenbus driver

   - two fixes by me fixing issues introduced in 5.6

   - a small cleanup by Gustavo Silva replacing a zero-length array with
     a flexible-array"

* tag 'for-linus-5.6b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/blkfront: fix ring info addressing
  xen/xenbus: fix locking
  xenbus: req->err should be updated before req->state
  xenbus: req->body should be updated before req->state
  xen: Replace zero-length array with flexible-array member