- 05 Sep, 2019 5 commits
-
-
Oded Gabbay authored
The ability of setting power management properties by the system administrator (through sysfs properties) is only relevant for the GOYA ASIC. Therefore, move the relevant sysfs properties to the GOYA sysfs specific file, to make the properties appear in sysfs only for GOYA cards. Signed-off-by:
Oded Gabbay <oded.gabbay@gmail.com> Reviewed-by:
Omer Shpigelman <oshpigelman@habana.ai>
-
Oded Gabbay authored
In the driver timeout functions, we give the simulator a factor of 10 in the timeout. This was necessary when the requested timeout is small but if it was a few seconds, this can result in a very large timeout which is unnecessary. This patch caps the maximum timeout of the simulator to 10 seconds, which is our largest timeout in the code. That is more then enough for anything the simulator is doing. Signed-off-by:
-
Oded Gabbay authored
When rejecting CS because of too many in-flight CS, print a debug message about it as it useful to know when the user is debugging (it indicates a back-pressure from the driver as the device is not fast enough to consume the CS) Signed-off-by:
-
Oded Gabbay authored
This patch adds some in-code documentation on the different opcodes of the INFO IOCTL. Signed-off-by:
-
Oded Gabbay authored
This property has attempted to show the number of open file descriptors on the device. This was a stupid and futile attempt so remove this property completely. Signed-off-by:
-
- 04 Sep, 2019 35 commits
-
-
Thomas Bogendoerfer authored
Add a 1-Wire slave driver to support DS250x EPROM deivces. This slave driver attaches the devices to the NVMEM subsystem for an easy in-kernel usage. Signed-off-by:
Thomas Bogendoerfer <tbogendoerfer@suse.de> Link: https://lore.kernel.org/r/20190831082623.15627-3-tbogendoerfer@suse.deSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Bogendoerfer authored
Starting with SGI Origin machines nearly every new SGI ASIC contains an 1-Wire master. They are used for attaching One-Wire prom devices, which contain information about part numbers, revision numbers, serial number etc. and MAC addresses for ethernet interfaces. This patch adds a master driver to support this IP block. It also adds an extra field dev_id to struct w1_bus_master, which could be in used in slave drivers for creating unique device names. Signed-off-by:
-
Adam Zerella authored
As suggested in https://kernelnewbies.org/KernelJanitors/Todo this patch replaces the outdated macro of DPRINTK for dev_dbg() To: Dominik Brodowski <linux@dominikbrodowski.net> To: Thomas Gleixner <tglx@linutronix.de> To: Adam Zerella <adam.zerella@gmail.com> To: linux-kernel@vger.kernel.org Signed-off-by:
Adam Zerella <adam.zerella@gmail.com> Link: https://lore.kernel.org/r/20190825053513.13990-1-adam.zerella@gmail.comSigned-off-by:
-
Daniel Mack authored
Add a paragraph to describe the use of the "of_id" module parameter, along with the new DT property. Signed-off-by:
Daniel Mack <daniel@zonque.org> Link: https://lore.kernel.org/r/20190815212807.25058-2-daniel@zonque.orgSigned-off-by:
-
Daniel Mack authored
When probed via DT, the uio_pdrv_genirq driver currently uses the name of the node and exposes that as name of the UIO device to userspace. This doesn't work for systems where multiple nodes with the same name (but different unit addresses) are present, or for systems where the node names are auto-generated by a third-party tool. This patch adds the possibility to read the UIO name from the optional "linux,uio-name" property. Signed-off-by:
-
Rishi Gupta authored
The printk functions are invoked without specifying required log level when printing error messages. This commit replaces all direct uses of printk with their corresponding pr_err/info/debug variant. Signed-off-by:
Rishi Gupta <gupt21@gmail.com> Link: https://lore.kernel.org/r/1566113671-8743-1-git-send-email-gupt21@gmail.comSigned-off-by:
-
Srinivas Kandagatla authored
dma buf scatter list is never freed, free it! Orignally detected by kmemleak: backtrace: [<ffffff80088b7658>] kmemleak_alloc+0x50/0x84 [<ffffff8008373284>] sg_kmalloc+0x38/0x60 [<ffffff8008373144>] __sg_alloc_table+0x60/0x110 [<ffffff800837321c>] sg_alloc_table+0x28/0x58 [<ffffff800837336c>] __sg_alloc_table_from_pages+0xc0/0x1ac [<ffffff800837346c>] sg_alloc_table_from_pages+0x14/0x1c [<ffffff8008097a3c>] __iommu_get_sgtable+0x5c/0x8c [<ffffff800850a1d0>] fastrpc_dma_buf_attach+0x84/0xf8 [<ffffff80085114bc>] dma_buf_attach+0x70/0xc8 [<ffffff8008509efc>] fastrpc_map_create+0xf8/0x1e8 [<ffffff80085086f4>] fastrpc_device_ioctl+0x508/0x900 [<ffffff80082428c8>] compat_SyS_ioctl+0x128/0x200 [<ffffff80080832c4>] el0_svc_naked+0x34/0x38 [<ffffffffffffffff>] 0xffffffffffffffff Reported-by:Mayank Chopra <mak.chopra@codeaurora.org> Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20190829092926.12037-6-srinivas.kandagatla@linaro.orgSigned-off-by:
-
Srinivas Kandagatla authored
dma buf refcount has to be done by the driver which is going to use the fd. This driver already does refcount on the dmabuf fd if its actively using it but also does an additional refcounting via extra ioctl. This additional refcount can lead to memory leak in cases where the applications fail to call the ioctl to decrement the refcount. So remove this extra refcount in the ioctl More info of dma buf usage at drivers/dma-buf/dma-buf.c Reported-by:
Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Tested-by:
-
Jorge Ramirez-Ortiz authored
Remove unused INIT_MEMLEN_MAX define. Signed-off-by:
Abhinav Asati <asatiabhi@codeaurora.org> Signed-off-by:
Vamsi Singamsetty <vamssi@codeaurora.org> Signed-off-by:
-
Bjorn Andersson authored
As fastrpc_rpmsg_remove() returns the rpdev of the channel context is no longer a valid object, so ensure to update the channel context to no longer reference the old object and guard in the invoke code path against dereferencing it. Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Bjorn Andersson authored
The channel context is referenced from the fastrpc user and might as user space holds the file descriptor open outlive the fastrpc device, which is removed when the remote processor is shutting down. Reference count the channel context in order to retain this object until all references has been relinquished. Signed-off-by:
-
Richard Gong authored
Add myself as maintainer for the newly created Intel Stratix10 firmware drivers. Signed-off-by:
Richard Gong <richard.gong@intel.com> Reviewed-by:
Alan Tull <atull@kernel.org> Link: https://lore.kernel.org/r/1567516701-26026-5-git-send-email-richard.gong@linux.intel.comSigned-off-by:
-
Richard Gong authored
Describe Intel Stratix10 Remote System Update (RSU) device attributes Signed-off-by:
-
Richard Gong authored
The Intel Remote System Update (RSU) driver exposes interfaces access through the Intel Service Layer to user space via sysfs interface. The RSU interfaces report and control some of the optional RSU features on Intel Stratix 10 SoC. The RSU feature provides a way for customers to update the boot configuration of a Intel Stratix 10 SoC device with significantly reduced risk of corrupting the bitstream storage and bricking the system. Signed-off-by:
-
Richard Gong authored
Extend Intel Stratix10 service layer driver to support new RSU notify and MAX_RETRY with watchdog event. RSU is used to provide our customers with protection against loading bad bitstream onto their devices when those devices are booting from flash RSU notifies provides users with an API to notify the firmware of the state of hard processor system. To deal with watchdog event, RSU provides a way for user to retry the current running image several times before giving up and starting normal RSU failover flow. Signed-off-by:
-
Scott Branden authored
Add tests cases for checking request_firmware_into_buf api. API was introduced into kernel with no testing present previously. Signed-off-by:
Scott Branden <scott.branden@broadcom.com> Acked-by:
Luis Chamberlain <mcgrof@kernel.org> Acked-by:
Shuah Khan <skhan@linuxfoundation.org> Link: https://lore.kernel.org/r/20190822184005.901-3-scott.branden@broadcom.comSigned-off-by:
-
Scott Branden authored
Add test config into_buf to allow request_firmware_into_buf to be called instead of request_firmware/request_firmware_direct. The number of parameters differ calling request_firmware_into_buf and support has not been added to test such api in test_firmware until now. Signed-off-by:
-
Hung-Te Lin authored
The VPD implementation from Chromium Vital Product Data project used to parse data from untrusted input without checking if the meta data is invalid or corrupted. For example, the size from decoded content may be negative value, or larger than whole input buffer. Such invalid data may cause buffer overflow. To fix that, the size parameters passed to vpd_decode functions should be changed to unsigned integer (u32) type, and the parsing of entry header should be refactored so every size field is correctly verified before starting to decode. Fixes: ad2ac9d5 ("firmware: Google VPD: import lib_vpd source files") Signed-off-by:
Hung-Te Lin <hungte@chromium.org> Cc: stable <stable@vger.kernel.org> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20190830022402.214442-1-hungte@chromium.orgSigned-off-by:
-
Tetsuo Handa authored
syzbot found that a thread can stall for minutes inside read_mem() or write_mem() after that thread was killed by SIGKILL [1]. Reading from iomem areas of /dev/mem can be slow, depending on the hardware. While reading 2GB at one read() is legal, delaying termination of killed thread for minutes is bad. Thus, allow reading/writing /dev/mem and /dev/kmem to be preemptible and killable. [ 1335.912419][T20577] read_mem: sz=4096 count=2134565632 [ 1335.943194][T20577] read_mem: sz=4096 count=2134561536 [ 1335.978280][T20577] read_mem: sz=4096 count=2134557440 [ 1336.011147][T20577] read_mem: sz=4096 count=2134553344 [ 1336.041897][T20577] read_mem: sz=4096 count=2134549248 Theoretically, reading/writing /dev/mem and /dev/kmem can become "interruptible". But this patch chose "killable". Future patch will make them "interruptible" so that we can revert to "killable" if some program regressed. [1] https://syzkaller.appspot.com/bug?id=a0e3436829698d5824231251fad9d8e998f94f5eSigned-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: stable <stable@vger.kernel.org> Reported-by:
syzbot <syzbot+8ab2d0f39fb79fe6ca40@syzkaller.appspotmail.com> Link: https://lore.kernel.org/r/1566825205-10703-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jpSigned-off-by:
-
Hridya Valsaraju authored
Currently /sys/kernel/debug/binder/proc contains the debug data for every binder_proc instance. This patch makes this information also available in a binderfs instance mounted with a mount option "stats=global" in addition to debugfs. The patch does not affect the presence of the file in debugfs. If a binderfs instance is mounted at path /dev/binderfs, this file would be present at /dev/binderfs/binder_logs/proc. This change provides an alternate way to access this file when debugfs is not mounted. Acked-by:
Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by:
Hridya Valsaraju <hridya@google.com> Link: https://lore.kernel.org/r/20190903161655.107408-5-hridya@google.comSigned-off-by:
-
Hridya Valsaraju authored
Currently, the binder transaction log files 'transaction_log' and 'failed_transaction_log' live in debugfs at the following locations: /sys/kernel/debug/binder/failed_transaction_log /sys/kernel/debug/binder/transaction_log This patch makes these files also available in a binderfs instance mounted with the mount option "stats=global". It does not affect the presence of these files in debugfs. If a binderfs instance is mounted at path /dev/binderfs, the location of these files will be as follows: /dev/binderfs/binder_logs/failed_transaction_log /dev/binderfs/binder_logs/transaction_log This change provides an alternate option to access these files when debugfs is not mounted. Acked-by:
-
Hridya Valsaraju authored
The following binder stat files currently live in debugfs. /sys/kernel/debug/binder/state /sys/kernel/debug/binder/stats /sys/kernel/debug/binder/transactions This patch makes these files available in a binderfs instance mounted with the mount option 'stats=global'. For example, if a binderfs instance is mounted at path /dev/binderfs, the above files will be available at the following locations: /dev/binderfs/binder_logs/state /dev/binderfs/binder_logs/stats /dev/binderfs/binder_logs/transactions This provides a way to access them even when debugfs is not mounted. Acked-by:
-
Hridya Valsaraju authored
Currently, all binder state and statistics live in debugfs. We need this information even when debugfs is not mounted. This patch adds the mount option 'stats' to enable a binderfs instance to have binder debug information present in the same. 'stats=global' will enable the global binder statistics. In the future, 'stats=local' will enable binder statistics local to the binderfs instance. The two modes 'global' and 'local' will be mutually exclusive. 'stats=global' option is only available for a binderfs instance mounted in the initial user namespace. An attempt to use the option to mount a binderfs instance in another user namespace will return an EPERM error. Signed-off-by:
-
Hridya Valsaraju authored
Currently, since each binderfs instance needs its own private binder devices, every time a binderfs instance is mounted, all the default binder devices need to be created via the BINDER_CTL_ADD IOCTL. This patch aims to add a solution to automatically create the default binder devices for each binderfs instance that gets mounted. To achieve this goal, when CONFIG_ANDROID_BINDERFS is set, the default binder devices specified by CONFIG_ANDROID_BINDER_DEVICES are created in each binderfs instance instead of global devices being created by the binder driver. Co-developed-by:
Joel Fernandes (Google) <joel@joelfernandes.org> Link: https://lore.kernel.org/r/20190808222727.132744-2-hridya@google.com Link: https://lore.kernel.org/r/20190904110704.8606-2-christian.brauner@ubuntu.comSigned-off-by:
-
Hridya Valsaraju authored
Length of a binderfs device name cannot exceed BINDERFS_MAX_NAME. This patch adds a check in binderfs_init() to ensure the same for the default binder devices that will be created in every binderfs instance. Co-developed-by:
-
Jean Delvare authored
Time has come to get rid of the old eeprom driver. The at24 driver should be used instead. So mark the eeprom driver as deprecated and give users some time to migrate. Then we can remove the legacy eeprom driver completely. Signed-off-by:
Jean Delvare <jdelvare@suse.de> Cc: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20190902104838.058725c2@endymionSigned-off-by:
-
Greg Kroah-Hartman authored
Merge tag 'fpga-dfl-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga into char-misc-next Moritz writes: FPGA DFL Changes for 5.4 This pull-request contains the FPGA DFL changes for 5.4 - The first three patches are cleanup patches making use of dev_groups and making the init callback optional. - One patch adds userclock sysfs entries that are DFL specific - One patch exposes AFU port disable/enable functions - One patch adds error reporting - One patch adds AFU SignalTap support - One patch adds FME global error reporting - The final patch is a documentation patch that decribes the virtualization interfaces This patchset requires the 'dev_groups_all_drivers' tag from drivers core for the dev_groups refactoring as well as the DFL changes already in char-misc-next. Signed-off-by:
Moritz Fischer <mdf@kernel.org> * tag 'fpga-dfl-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga: Documentation: fpga: dfl: add descriptions for virtualization and new interfaces. fpga: dfl: fme: add global error reporting support fpga: dfl: afu: add STP (SignalTap) support fpga: dfl: afu: add error reporting support. fpga: dfl: afu: expose __afu_port_enable/disable function. fpga: dfl: afu: add userclock sysfs interfaces. fpga: dfl: afu: convert platform_driver to use dev_groups fpga: dfl: fme: convert platform_driver to use dev_groups fpga: dfl: make init callback optional driver core: add dev_groups to all drivers
-
Wu Hao authored
This patch adds virtualization support description for DFL based FPGA devices (based on PCIe SRIOV), and introductions to new interfaces added by new dfl private feature drivers. [mdf@kernel.org: Fixed up to make it work with new reStructuredText docs] Signed-off-by:
Xu Yilun <yilun.xu@intel.com> Signed-off-by:
Wu Hao <hao.wu@intel.com> Acked-by:
-
Wu Hao authored
This patch adds support for global error reporting for FPGA Management Engine (FME), it introduces sysfs interfaces to report different error detected by the hardware, and allow user to clear errors or inject error for testing purpose. Signed-off-by:
Luwei Kang <luwei.kang@intel.com> Signed-off-by:
Ananda Ravuri <ananda.ravuri@intel.com> Signed-off-by:
-
Wu Hao authored
STP (SignalTap) is one of the private features under the port for debugging. This patch adds private feature driver support for it to allow userspace applications to mmap related mmio region and provide STP service. Signed-off-by:
-
Wu Hao authored
Error reporting is one important private feature, it reports error detected on port and accelerated function unit (AFU). It introduces several sysfs interfaces to allow userspace to check and clear errors detected by hardware. Signed-off-by:
-
Wu Hao authored
As these two functions are used by other private features within the same driver module but different driver files. e.g. in error reporting private feature, it requires to clear errors when port is in reset. Signed-off-by:
-
Wu Hao authored
This patch introduces userclock sysfs interfaces for AFU, user could use these interfaces for clock setting to AFU. Please note that, this is only working for port header feature with revision 0, for later revisions, userclock setting is moved to a separated private feature, so one revision sysfs interface is exposed to userspace application for this purpose too. Signed-off-by:
Russ Weight <russell.h.weight@intel.com> Signed-off-by:
-
Wu Hao authored
This patch takes advantage of driver core which helps to create and remove sysfs attribute files, so there is no need to register sysfs entries manually in dfl-afu platform river code. Signed-off-by:
-
Wu Hao authored
This patch takes advantage of driver core which helps to create and remove sysfs attribute files, so there is no need to register sysfs entries manually in dfl-fme platform river code. Signed-off-by:
-
