- 08 Oct, 2019 1 commit
-
-
Mauro Carvalho Chehab authored
As reported by jenkins@linuxtv.org, the build with i386 fails with: ld: drivers/media/platform/qcom/venus/helpers.o: in function `venus_helper_load_scale_clocks': (.text+0x1d77): undefined reference to `__udivdi3' ld: (.text+0x1dce): undefined reference to `__udivdi3' make: *** [Makefile:1094: vmlinux] Error 1 That's because it divides an u32 bit integer by a u64 one. Reviewed-by:
Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
- 07 Oct, 2019 24 commits
-
-
Hans Verkuil authored
When the new CEC_OP_UI_CMD defines were added I forgot to update this header to use these new defines. This is now fixed. Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
Hans Verkuil authored
The CEC_MSG_GIVE_DECK_STATUS and CEC_MSG_GIVE_TUNER_DEVICE_STATUS commands both have a status_req argument: ON, OFF, ONCE. If ON or ONCE, then the follower will reply with a STATUS message. Either once or whenever the status changes (status_req == ON). If status_req == OFF, then it will stop sending continuous status updates, but the follower will *not* send a STATUS message in that case. This means that if status_req == OFF, then msg->reply should be 0 as well since no reply is expected in that case. Signed-off-by:
-
Yang Yingliang authored
If usb_set_interface() failed, iface->cur_altsetting will not be assigned and it will be used in flexcop_usb_transfer_init() It may lead a NULL pointer dereference. Check usb_set_interface() return value in flexcop_usb_init() and return failed to avoid using this NULL pointer. Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Akihiro Tsukada authored
Support Friio devices to read from tuner via demod tc90522, by enabling the config option. Signed-off-by:
Akihiro Tsukada <tskd08@gmail.com> Signed-off-by:
-
Akihiro Tsukada authored
This demod implements an i2c adapter for attached tuner and relays i2c messages from users (dvb adapters / bridge chips). Some of them, such as Friio dvb card using gl861, require each pair of i2c messages for one read to be issued as two separate transactions. This patch adds a configuration option to enable this split. Signed-off-by:
-
Akihiro Tsukada authored
The header contained just internal definitions and they are not used anymore. Signed-off-by:
-
Akihiro Tsukada authored
For Friio dvb cards, a distinct I2C algo was provided to support some "long" I2C messages used in relaying tuner I2C via demod. Since the other (generic) i2c algo in this module has been patched to support those messages in a more generic way, this patch replaces and integrates the device-specific i2c algo with the generic one and simplifies the code. Signed-off-by:
-
Antti Palosaari authored
Device I2C adapter is capable of writing and reading large messages. For I2C writes there is 2 methods: simple for max 2 byte messages and usb_control_msg() with payload data for larger I2C messages. Add I2C adapter logic which selects suitable method according to message size. Add also support for plain I2C read. Cc: Akihiro TSUKADA <tskd08@gmail.com> Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Andrei Koshkosh authored
Re-use usb_mutex from dvb_usb_device for this. Tested-by:
Jan Pieter van Woerkom <jp@jpvw.nl> Signed-off-by:
Andrei Koshkosh <andreykosh000@mail.ru> Signed-off-by:
-
Colin Ian King authored
The variable rc is being initialized with a value that is never read and it is being updated later with a new value. The initialization is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Nishad Kamdar authored
This patch corrects the SPDX License Identifier style in header files for TV Master Media USB Adapter drivers. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used) Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by:
Joe Perches <joe@perches.com> Signed-off-by:
Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by:
-
Markus Elfring authored
Simplify this function implementation by using a known wrapper function. This issue was detected by using the Coccinelle software. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Acked-by:
Mans Rullgard <mans@mansr.com> Signed-off-by:
-
Nishad Kamdar authored
This patch corrects the SPDX License Identifier style in header file related to Remote Controller Driver for Linux. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used) Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by:
-
Navid Emamdoost authored
In cx23888_ir_probe if kfifo_alloc fails the allocated memory for state should be released. Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by:
-
Dominik Danelski authored
Add support for Magix Wideowandler 2 - analog USB capture card Signed-off-by:
Dominik Danelski <dominik@danelski.pl> Co-author: Cornelius Porosanu <cornelius591@gmail.com> Signed-off-by:
-
Colin Ian King authored
Don't populate the array tab on the stack but instead make it static const. Makes the object size smaller by 170 bytes in total. Before: text data bss dec hex filename 7045 1736 0 8781 224d media/dvb-frontends/cxd2820r_c.o 8800 2216 0 11016 2b08 media/dvb-frontends/cxd2820r_t.o 8981 2120 0 11101 2b5d media/dvb-frontends/cxd2820r_t2.o After: text data bss dec hex filename 6896 1832 0 8728 2218 media/dvb-frontends/cxd2820r_c.o 8651 2312 0 10963 2ad3 media/dvb-frontends/cxd2820r_t.o 8853 2184 0 11037 2b1d media/dvb-frontends/cxd2820r_t2.o (gcc version 9.2.1, amd64) Signed-off-by:
-
Sean Young authored
Currently the IR receiver is put into idle mode after each interrupt. However longer IR like NEC can be distributed over multiple interrupts, so putting the IR into idle in the middle of such a message will break decoding. Every IR message has a trailing space of 0xbf (one less than IR_IDE_LEN{0,1} which is programmed to 0xc0). So, set the timeout to that value and rc-core will put the IR receiver into idle mode automatically. Thanks to Jan Pieter van Woerkom <jp@jpvw.nl> for providing the hardware. Signed-off-by: -
Sean Young authored
Thanks to Jan Pieter van Woerkom <jp@jpvw.nl> for providing the hardware. Signed-off-by:
-
Flavius Georgescu authored
The device it's an iMON UltraBay (0x98 in config byte) with LCD, IR and dual-knobs front panel. To work properly the device also require its own key table, and repeat suppression for all buttons. Signed-off-by:
Flavius Georgescu <pretoriano.mp@gmail.com> Co-developed-by:
Chris Vandomelen <chris@sightworks.com> Signed-off-by:
-
A Sun authored
Fix multiple cases of out of bounds (OOB) read associated with MCE device receive/input data handling. In reference for the OOB cases below, the incoming/read (byte) data format when the MCE device responds to a command is: { cmd_prefix, subcmd, data0, data1, ... } where cmd_prefix are: MCE_CMD_PORT_SYS MCE_CMD_PORT_IR and subcmd examples are: MCE_RSP_GETPORTSTATUS MCE_RSP_EQIRNUMPORTS ... Response size dynamically depends on cmd_prefix and subcmd. So data0, data1, ... may or may not be present on input. Multiple responses may return in a single receiver buffer. The trigger condition for OOB read is typically random or corrupt input data that fills the mceusb receiver buffer. Case 1: mceusb_handle_command() reads data0 (var hi) and data1 (var lo) regardless of whether the response includes such data. If { cmd_prefix, subcmd } is at the end of the receiver buffer, read past end of buffer occurs. This case was reported by KASAN: slab-out-of-bounds Read in mceusb_dev_recv https://syzkaller.appspot.com/bug?extid=c7fdb6cb36e65f2fe8c9 Fix: In mceusb_handle_command(), change variable hi and lo to pointers, and dereference only when required. Case 2: If response with data is truncated at end of buffer after { cmd_prefix, subcmd }, mceusb_handle_command() reads past end of buffer for data0, data1, ... Fix: In mceusb_process_ir_data(), check response size with remaining buffer size before invoking mceusb_handle_command(). + if (i + ir->rem < buf_len) mceusb_handle_command(ir, &ir->buf_in[i - 1]); Case 3: mceusb_handle_command() handles invalid/bad response such as { 0x??, MCE_RSP_GETPORTSTATUS } of length 2 as a response { MCE_CMD_PORT_SYS, MCE_RSP_GETPORTSTATUS, data0, ... } of length 7. Read OOB occurs for non-existent data0, data1, ... Cause is mceusb_handle_command() does not check cmd_prefix value. Fix: mceusb_handle_command() must test both cmd_prefix and subcmd. Case 4: mceusb_process_ir_data() receiver parser state SUBCMD is possible at start (i=0) of receiver buffer resulting in buffer offset=-1 passed to mceusb_dev_printdata(). Bad offset results in OOB read before start of buffer. [1214218.580308] mceusb 1-1.3:1.0: rx data[0]: 00 80 (length=2) [1214218.580323] mceusb 1-1.3:1.0: Unknown command 0x00 0x80 ... [1214218.580406] mceusb 1-1.3:1.0: rx data[14]: 7f 7f (length=2) [1214218.679311] mceusb 1-1.3:1.0: rx data[-1]: 80 90 (length=2) [1214218.679325] mceusb 1-1.3:1.0: End of raw IR data [1214218.679340] mceusb 1-1.3:1.0: rx data[1]: 7f 7f (length=2) Fix: If parser_state is SUBCMD after processing receiver buffer, reset parser_state to CMD_HEADER. In effect, discard cmd_prefix at end of receiver buffer. In mceusb_dev_printdata(), abort if buffer offset is out of bounds. Case 5: If response with data is truncated at end of buffer after { cmd_prefix, subcmd }, mceusb_dev_printdata() reads past end of buffer for data0, data1, ... while decoding the response to print out. Fix: In mceusb_dev_printdata(), remove unneeded buffer offset adjustments (var start and var skip) associated with MCE gen1 header. Test for truncated MCE cmd response (compare offset+len with buf_len) and skip decoding of incomplete response. Move IR data tracing to execute before the truncation test. Signed-off-by:A Sun <as1033x@comcast.net> Signed-off-by:
-
Sean Young authored
Decoding often fails on e.g. redrat3 devices. The dev_dbg() helps with debugging when decoding does fail. Cc: Patrick Lerda <patrick9876@free.fr> Signed-off-by:
-
Sean Young authored
libinput refuses pointer movement from rc-core, since it believes it's not a pointer-type device: libinput error: event17 - Media Center Ed. eHome Infrared Remote Transceiver (1784:0008): libinput bug: REL_X/Y from a non-pointer device Fixes: 158bc148 ("media: rc: mce_kbd: input events via rc-core's input device") Fixes: 0ac5a603 ("media: rc: imon: report mouse events using rc-core's input device") Cc: stable@vger.kernel.org # 4.20+ Signed-off-by:
-
Sean Young authored
procfs is no longer used anywhere in media. Signed-off-by:
-
Sean Young authored
This moves /proc/saa7164 to /sys/kernel/debug/saa7164. Signed-off-by:
-
- 04 Oct, 2019 3 commits
-
-
Aniket Masule authored
Current clock scaling calculations are same for vpu4 and previous versions. For vpu4, Clock scaling calculations are updated with cycles/mb and bitrate. This helps in getting precise clock required. Signed-off-by:
Aniket Masule <amasule@codeaurora.org> Signed-off-by:
-
Aniket Masule authored
Add vpp cycles for different types of codec. It indicates the cycles required by video hardware to process each macroblock. Add vsp cycles, cycles required by stream processor. Initialize the codec data with core resources. Signed-off-by:
-
Stanimir Varbanov authored
Failure to suspend (venus_suspend_3xx) happens when the system is fresh booted and loading venus driver. This happens once and after reload the venus driver modules the problem disrepair. Fix the failure by skipping the check for WFI and IDLE bits if PC_READY is on in control status register. Signed-off-by:
-
- 02 Oct, 2019 2 commits
-
-
Stanimir Varbanov authored
This aims to add a requests for bandwidth scaling depending on the resolution and framerate (macroblocks per second). The exact value of the requested bandwidth is get from a pre-calculated tables for encoder and decoder. Acked-by:
Georgi Djakov <georgi.djakov@linaro.org> Signed-off-by:
-
Loic Poulain authored
In downstream driver, there are two frequency tables defined, one for the encoder and one for the decoder: /* Encoders / <972000 490000000 0x55555555>, / 4k UHD @ 30 / <489600 320000000 0x55555555>, / 1080p @ 60 / <244800 150000000 0x55555555>, / 1080p @ 30 / <108000 75000000 0x55555555>, / 720p @ 30 */ /* Decoders / <1944000 490000000 0xffffffff>, / 4k UHD @ 60 / < 972000 320000000 0xffffffff>, / 4k UHD @ 30 / < 489600 150000000 0xffffffff>, / 1080p @ 60 / < 244800 75000000 0xffffffff>; / 1080p @ 30 */ It shows that encoder always needs a higher clock than decoder. In current venus driver, the unified frequency table is aligned with the downstream decoder table which causes performance issues in encoding scenarios. Fix that by aligning frequency table on worst case (encoding). Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
-
- 01 Oct, 2019 10 commits
-
-
Benoit Parrot authored
Switch to SPDX licensing and drop the redundant GPL text. Signed-off-by:
Benoit Parrot <bparrot@ti.com> Acked-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Benoit Parrot authored
The initial registers sequence is only loaded at probe time. Afterward only the resolution and format specific register are modified. Care must be taken to make sure registers modified by one resolution setting are reverted back when another resolution is programmed. This was not done properly for the 720p case. Signed-off-by:
-
Benoit Parrot authored
On some board it is possible that the sensor 'powerdown' and or 'reset' pin might be controlled by gpio instead of being tied. To implement we add pm_runtime support which will handle the power up/down sequence when it is available otherwise the sensor will be powered on at module insertion/probe and powered off at module removal. Now originally the driver assumed that the sensor would always stay powered and keep its register setting. We cannot assume this anymore, so every time we "power up" we need to re-program the initial registers configuration first. This was previously done only at probe time. [Sakari Ailus: Resolve a conflict in Kconfig] Signed-off-by:
-
Benoit Parrot authored
Add powerdown-gpios and reset-gpios to the list of optional properties for the OV2659 camera sensor. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Benoit Parrot authored
In ov2659_s_stream() return value for invoked function should be checked and propagated. Signed-off-by:
-
Benoit Parrot authored
Several of include files listed are not explicitly needed. If they are need then they are implicitly included. Reduce the list of includes to an easier to manage list. Signed-off-by:
-
Benoit Parrot authored
Make sure that if the expected sensor device id register is not recognized properly the failure is propagated up so devices are not left partially initialized. Signed-off-by:
Jyri Sarha <jsarha@ti.com> Acked-by:
-
Benoit Parrot authored
Based on recently found sensor configuration examples, it was discovered that when scaling and binning are used for the lower resolutions (i.e. 640x480, 320x240) the read offset has to be increased otherwise the image appears to be wrapped around. Signed-off-by:
-
Dongchun Zhu authored
This patch adds support for registering a sensor sub-device to the async sub-device framework and parse set up common sensor related devices such as actuator/VCM. [Sakari Ailus: Rewrap commit message] Signed-off-by:
Dongchun Zhu <dongchun.zhu@mediatek.com> Reviewed-by:
Tomasz Figa <tfiga@chromium.org> Signed-off-by:
-
Sakari Ailus authored
Assign vep->link_frequencies to NULL after releasing its memory. Without this change, multiple calls to v4l2_fwnode_endpoint_free() would result in double kfree calls. Signed-off-by:
-
