Handle both enable-gpio and enable-gpios properties of the GPIO
regulator in the quirk. The later is the preferred modern name
of the property.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jan Kotas <jank@cadence.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: linux-renesas-soc@vger.kernel.org
To: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Commit 0e7d6f94 ("gpio: of: Apply regulator-gpio quirk only to
enable-gpios") breaks the device tree ABI specified in the device tree
bindings for fixed regulators (compatible "regulator-fixed"). According
to these bindings the polarity of the GPIO is exclusively controlled by
the presence or absence of the enable-active-high property. As such the
polarity quirk implemented in of_gpio_flags_quirks() must be applied to
the GPIO specified for fixed regulators.

However, commit 0e7d6f94 ("gpio: of: Apply regulator-gpio quirk only
to enable-gpios") restricted the quirk to the enable-gpios property for
fixed regulators as well, whereas according to the commit message itself
it should only apply to "regulator-gpio" compatible device tree nodes.

Fix this by actually implementing what the offending commit intended,
which is to ensure that the quirk is applied to the GPIO specified by
the "enable-gpio" property for the "regulator-gpio" bindings only.

This fixes a regression on Jetson TX1 where the fixed regulator for the
HDMI +5V pin relies on the flags quirk for the proper polarity.

Fixes: 0e7d6f94 ("gpio: of: Apply regulator-gpio quirk only to enable-gpios")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use the new helper that wraps the calls to platform_get_resource() and
devm_ioremap_resource() together.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There are currently 1200+ instances of using platform_get_resource()
and devm_ioremap_resource() together in the kernel tree.

This patch wraps these two calls in a single helper. Thanks to that
we don't have to declare a local variable for struct resource * and can
omit the redundant argument for resource type. We also have one
function call less.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

According to the manpage of poll(2) and also looking at the respective
syscall providing POLLERR in .events is a no-op. So don't recommend
using it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Implement the irq_set_wake() method in the (optional) irq_chip of the
GPIO expander, and propagate wake-up settings to the upstream interrupt
controller.  This allows GPIOs connected to a PCA953X GPIO expander to
serve as wake-up sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'gpio-v5.1-updates-for-linus-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel

gpio: updates for v5.1 - part 2

- gpio-mockup updates improving the user-space testing interface and
  adding line state tracking for correct edge interrupts
- interrupt simulator patch exposing the irq type configuration to
  users

This patch hunk is a lightly modified version of a diff found
in a Tegra code dump from a product tree. It makes a lot of
sense because this is what most drivers do.

Cc: Thierry Reding <treding@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Modify the way the debugfs interface works in gpio-mockup. Introduce
the concept of dummy pull config which will keep the mockup lines in
known state. The pull values can be modified by writing to the debugfs
files corresponding to lines. Lines in input mode always report the
current pull value, lines in output mode change the line value but
it will revert back to the one specified by current pull when released.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The unlocked variants only get called from places where we already have
the pointer to the underlying gpio_mockup_chip structure, so take it
as parameter instead of struct gpio_chip.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

This field can never be negative.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

User-space tests no longer use it and we're breaking the interface
anyway.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

We already support set_multiple(). Implement get_multiple() as well.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

While no user reported any race condition problems with gpio-mockup,
let's be on the safe side and use a mutex when performing any changes
on the dummy chip structures.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Implement the irq_set_type() callback and call irqd_set_trigger_type()
internally so that users interested in the configured trigger type can
later retrieve it using irqd_get_trigger_type(). We only support edge
trigger types.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>

Since commit d6cd33ad ("regulator: gpio: Convert to use descriptors")
the GPIO regulator had inverted the polarity of the control GPIO. This
problem manifested itself on systems with DT containing the following
description (snippet from salvator-common.dtsi):

	gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
	gpios-states = <1>;
	states = <3300000 1
		  1800000 0>;

Prior to the aforementioned commit, the gpio-regulator code used
gpio_request_array() to claim the GPIO(s) specified in the "gpios"
DT node, while the commit changed that to devm_gpiod_get_index().

The legacy gpio_request_array() calls gpio_request_one() and then
gpiod_request(), which parses the DT flags of the "gpios" node and
populates the GPIO descriptor flags field accordingly.

The new devm_gpiod_get_index() calls gpiod_get_index(), then
of_find_gpio(), of_get_named_gpiod_flags() with flags != NULL,
and then of_gpio_flags_quirks(). Since commit a603a2b8
("gpio: of: Add special quirk to parse regulator flags"),
of_gpio_flags_quirks() contains a quirk for regulator-gpio
which was never triggered by the legacy gpio_request_array()
code path, but is triggered by devm_gpiod_get_index() code
path.

This quirk checks whether a GPIO is associated with a fixed
or gpio-regulator and if so, checks two additional conditions.
First, whether such GPIO is active-low, and if so, ignores the
active-low flag. Second, whether the regulator DT node does
have an "enable-active-high" property and if the property is
NOT present, sets the GPIO flags as active-low.

The second check triggers a problem, since it is applied to all
GPIOs associated with a gpio-regulator, rather than only on the
"enable" GPIOs, as the old code did. This changes the way the
gpio-regulator interprets the DT description of the control
GPIOs.

The old code using gpio_request_array() explicitly parsed the
"enable-active-high" DT property and only applied it to the
GPIOs described in the "enable-gpios" DT node, and only if
those were present.

This patch fixes the quirk code by only applying the quirk
to "enable-gpios", thus restoring the old behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jan Kotas <jank@cadence.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: linux-renesas-soc@vger.kernel.org
To: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'intel-gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel

intel-gpio for v5.1-1

Small clean up for Intel PMIC GPIO drivers, includes:
 - optimizing IRQ handlers by usage of for_each_set_bit()
 - sorting headers alphabetically for better maintenance
 - conversion to SPDX identifier

The following is an automated git shortlog grouped by driver:

crystalcove:
 -  Convert to use SPDX identifier
 -  Sort headers alphabetically
 -  Use for_each_set_bit() in IRQ handler

msic:
 -  Convert to use SPDX identifier
 -  Sort headers alphabetically
 -  Remove duplicate check in IRQ handler

wcove:
 -  Convert to use SPDX identifier
 -  Fix indentation
 -  Sort headers alphabetically
 -  Allow return negative error code from to_reg()

Merge tag 'gpio-v5.1-updates-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel

gpio updates for v5.1

- support for a new variant of pca953x
- documentation fix from Wolfram
- some tegra186 name changes
- two minor fixes for madera and altera-a10sr

Change the coding style to make it does error checking first.
This also fixes checkpatch warning about line over 80 characters.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The new prefix allows the GPIOs to be uniquely identified on a per-chip
basis, which makes it easier to distinguish Tegra186 specific GPIOs from
those of later chips such as Tegra194 which supports a very different
set of GPIOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Typo: the data line is called "SDA" not "SCA".
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

madera_gpio_chip is only used as a template so it can be marked as const.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The NXP PCAL6416, documented at [1], is a variant of the PCA GPIO
expander with 16 GPIOs, and supporting an interrupt and the "extended"
features for interrupt, pull-up/pull-down configuration, etc.

[1] https://www.nxp.com/docs/en/data-sheet/PCAL6416A.pdfSigned-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The NXP PCAL6416 is a variant of the PCA GPIO expander, with 16 GPIOs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

SSBI GPIOs are numbered 1..ngpio, so the boundary check in
pm8xxx_domain_translate() is off by one. This patch corrects that check.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Select IRQ_DOMAIN_HIERARCHY for pm8xxx in Kconfig since this driver uses
the version 2 IRQ interfaces. IRQ_DOMAIN_HIERARCHY selects IRQ_DOMAIN,
so it can be removed from here.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Select IRQ_DOMAIN_HIERARCHY for pmic-arb in Kconfig since this driver
uses the version 2 IRQ interfaces. IRQ_DOMAIN_HIERARCHY selects
IRQ_DOMAIN, so it can be removed from here.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Unlike gpio_rcar_irq_set_wake(), which this solution was based on,
pcf857x_irq_set_wake() does not need to do anything else than calling
irq_set_irq_wake() for the upstream interrupt controller.  Hence there
is no reason for making this call conditional, and no longer a need for
keeping a copy of the interrupt number that also serves as a flag.

Just propagate irq_set_irq_wake() to the upstream interrupt controller,
using the original interrupt number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix the following warning by adding a missing break:

drivers/gpio/gpio-eic-sprd.c: In function ‘sprd_eic_irq_set_type’:
drivers/gpio/gpio-eic-sprd.c:403:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
   switch (flow_type) {
   ^~~~~~
drivers/gpio/gpio-eic-sprd.c:435:2: note: here
  default:
  ^~~~~~~

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Zynq GPIO driver currently implements runtime PM by:

 - Enabling runtime PM support in ->probe() and letting the runtime PM
   reference counter drop to zero at the end of ->probe().

 - Increasing the runtime PM reference counter in ->request() and
   decreasing it in ->free().

However, the latter is not sufficient: when a GPIO is used as an
interrupt, ->request() and ->free() are not called. Due to this, the
runtime PM counter remains to zero when the only GPIOs in use are used
as interrupts, causing them to simply not work.

To address this problem, this commit implement the
->irq_request_resources() and ->irq_release_resources() hooks,
ensuring that the runtime PM counter is properly
incremented/decremented. Since we override the default hooks, we keep
the existing behavior by making sure they call gpiochip_reqres_irq() /
gpiochip_relres_irq() respectively.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now that ssbi-gpio is a proper hierarchical IRQ chip, and all in-tree
users of device tree have been updated, we can now drop the hack that
was introduced to disassociate the old Linux virq if a hwirq mapping
already exists. That patch was introduced to not break git bisect for
any existing boards.

This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Before we fixed up the interrupt hierarchy for the SSBI
GPIO controller, we had to use the PM8058 directly to pick
interrupts. After making the interrupt controller work properly,
we can reference the real interrupt parent.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add interrupt controller properties now that ssbi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.

Note that the IRQs started at 24 instead of 192 like all of the other
PMICs. This is the same IRQs as the MPP for this board. qcom-pm8xxx.c
doesn't set the shared IRQs so this is highly likely to be a copy and
paste error.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add interrupt controller properties now that ssbi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.

This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add interrupt controller properties now that ssbi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.

This change was not tested on any hardware but the same change was
tested on an APQ8060 DragonBoard with no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

ssbi-gpio did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should
be usable from the start without the consumer having to make an
additional call to get the proper IRQ on the parent. This patch adds
hierarchical IRQ chip support to the ssbi-gpio code to correct this
issue.

The constant PM8XXX_GPIO_PHYSICAL_OFFSET is introduced to replace the
hardcoded '1' that previously existed in two places in this driver to
improve code readability.

This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Check to see if the hwirq is already associated with another virq on
this IRQ domain. If so, then disassociate it before associating the
hwirq with the new virq.

This is a temporary hack that is needed in order to not break git
bisect for existing boards. The next patch in this series converts
ssbi-gpio to be a hierarchical IRQ chip, then there are several patches
to update all of the device tree files, and finally this patch will be
reverted within the same patch series.

IRQs for ssbi-gpio are all initially setup without an IRQ hierarchy
this driver is probed due to the interrupts property in device tree.
Once ssbi-gpio is converted to be a hierarchical IRQ chip in the next
patch, existing users of gpio[d]_to_irq() will call pmic_gpio_to_irq(),
and that will use the new IRQ chip code in ssbi-gpio that sets up the
IRQ in an IRQ hierarchy. The hwirq is now associated with two Linux
virqs and interrupts will not work as expected. This patch corrects
that issue.

This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Convert the PM8XXX IRQ code to use the version 2 IRQ interface in order
to support hierarchical IRQ chips. This is necessary so that ssbi-gpio
can be setup as a hierarchical IRQ chip with PM8xxx as the parent. IRQ
chips in device tree should be usable from the start without having to
make an additional call to gpio[d]_to_irq() to get the proper IRQ on the
parent.

pm8821_irq_domain_ops and pm8821_irq_domain_map are removed by this
patch since the irq_chip is now contained in the pm_irq_data struct, and
that allows us to use a common IRQ mapping function.

This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>