Simplify:
	- set ECB
	...
	- LCR mode A
	- clear TCRTLR
	- LCR mode B
	- clear ECB
	- set ECB and update other bits
	- LCR mode A
	- update XONANY

to:
	- set ECB
	...
	- LCR mode B
	- set ECB and update other bits
	- LCR mode A
	- update XONANY and clear TCRTLR
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Take advantage of the switch to mode B for accessing the TCR register,
and move the xon/xoff configuration there.  This allows further
simplication of this sequence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We always setup the TCR register in the software flow control path,
and when hardware flow control is enabled.  Remove this redundant
setup, and place it before we setup any hardware flow control.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We have the sequence:
	- LCR mode B
	- write EFR with ECB clear
	- LCR mode normal
	- if s/w flow
		- LCR mode B
		- write EFR with ECB clear
		...
		- LCR mode B
		- write EFR with ECB clear
		- LCR mode normal

This can be simplified to:
	- if s/w flow
		- LCR mode B
		- write EFR with ECB clear
		...
	- LCR mode B
	- write EFR with ECB clear
	- LCR mode normal
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There's really no reason to read back these registers while setting
the termios modes, provided we keep our cached copies up to date.
Remove these readbacks.

This has the benefit that we know that the EFR_ECB and MCR_TCRTLR
bits will always be clear, so we don't need to keep masking these
bits throughout the code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

OMAP_UART_SYSC_RESET and OMAP_UART_FIFO_CLR are unused, remove them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

struct uart_omap_port and struct uart_omap_dma, and associated
definitions are private to the driver, so there's no point them sitting
in an include file under arch/arm.  Move them into the driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

irq_pending is never used, so let's remove it.  It seems to be  result
of a bad rebase of d37c6ceb (serial: omap: move uart_omap_port
definition to C file)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The MCR TCRTLR bit can only be changed when ECB is set in the EFR.
Unfortunately, several places were trying to alter this bit while ECB
was clear:

- serial_omap_configure_xonxoff() was attempting to clear the bit after
  explicitly clearing the ECB bit.
- serial_omap_set_termios() was trying the same trick after setting the
  SCR, and when trying to change the TCR register when hardware flow
  control was enabled.

Fix this by ensuring that we always have ECB set whenever the TCRTLR bit
is changed.

Moreover, we start out by reading the EFR and MCR registers, which may
have indeterminent bit settings for the ECB and TCRTLR bits.  Ensure
that these bits always start off in a known state.

In order to avoid any undesired behaviour appearing through fixing this,
we also ensure that hardware assisted flow control is disabled while new
driver specific parts are not in place.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

c538d20c (and maybe previous commits) broke set_mctrl() by making
it only capable of setting bits in the MCR register.  This prevents
software controlled flow control and modem control line manipulation
via TIOCMSET/TIOCMBIC from working correctly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There's no need to re-read EFR after we've recently written it; the
register is a configuration register which doesn't change its value
without us writing to it.  The last value which was written to this
register was up->efr.

Removing this re-reading avoids the possibility that we end up with
up->efr having unintended bits set, which should only be temporarily
set when accessing the enhanced features.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The SCD (special character detect) bit enables comparisons with XOFF2,
which we do not program.  As the XOFF2 character remains unprogrammed,
there's little point enabling this feature along with its associated
interrupt.  Remove this, and ensure that the SCD bit is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Nothing was clearing the UART_MCR_XONANY bit, so once the ixany
mode gets set, there's no possibility to disable it.  Clear this
bit when IXANY mode is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There is nothing which clears the auto RTS/CTS bits, so once hardware
flow control gets enabled, there's no possibility to disable it.
So, clear these bits when CRTSCTS is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add two callbacks for hardware assisted flow control; we need to know
when the tty layers want us to stop and restart due to their buffer
levels.

Call a driver specific throttle/unthrottle function if and only if the
driver indicates that it is using an enabled hardware assisted flow
control method, otherwise fall back to the non-hardware assisted
methods.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Ports which are handling h/w flow control in hardware must not have
their RTS state altered depending on the tty's hardware-stopped state.
Avoid this additional logic when setting the termios state.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Ports which are capable of handling s/w flow control in hardware to
know when the s/w flow control termios settings are changed.  Add a
flag to allow the low level serial drivers to indicate that they
support this, and these changes should be propagated to them.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This is to make the following change more clear.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull ktest confusion fix from Steven Rostedt:
 "With the v3.7-rc2 kernel, the network cards on my target boxes were
  not being brought up.

  I found that the modules for the network was not being installed.
  This was due to the config CONFIG_MODULES_USE_ELF_RELA that came
  before CONFIG_MODULES, and confused ktest in thinking that
  CONFIG_MODULES=y was not found.

  Ktest needs to test all configs and not just stop if something starts
  with CONFIG_MODULES."

* tag 'ktest-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Fix ktest confusion with CONFIG_MODULES_USE_ELF_RELA

Pull minor spi MXS fixes from Mark Brown:
 "These fixes are both pretty minor ones and are driver local."

* tag 'spi-mxs' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
  spi: mxs: Terminate DMA in case of DMA timeout
  spi: mxs: Assign message status after transfer finished

Pull arm-soc fixes from Arnd Bergmann:
 "Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.

  These come a little later than I had hoped but unfortunately we had a
  few of these patches cause regressions themselves and had to work out
  how to deal with those in the meantime."

* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
  Revert "ARM i.MX25: Fix PWM per clock lookups"
  ARM: versatile: fix versatile_defconfig
  ARM: mvebu: update defconfig with 3.7 changes
  ARM: at91: fix at91x40 build
  ARM: socfpga: Fix socfpga compilation with early_printk() enabled
  ARM: SPEAr: Remove unused empty files
  MAINTAINERS: Add arm-soc tree entry
  ARM: dts: mxs: add the "clock-names" for gpmi-nand
  ARM: ux500: Correct SDI5 address and add some format changes
  ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
  ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
  ARM: at91: drop duplicated config SOC_AT91SAM9 entry
  ARM: at91/i2c: change id to let i2c-at91 work
  ARM: at91/i2c: change id to let i2c-gpio work
  ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
  ARM: at91: fix external interrupt specification in board code
  ARM: at91: fix external interrupts in non-DT case
  ARM: at91: at91sam9g10: fix SOC type detection
  ARM: at91/tc: fix typo in the DT document
  ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
  ...

Functions generic_file_splice_read and generic_file_splice_write access
the pagecache directly. For block devices these functions must be locked
so that block size is not changed while they are in progress.

This patch is an additional fix for commit b87570f5 ("Fix a crash
when block device is read and block size is changed at the same time")
that locked aio_read, aio_write and mmap against block size change.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use rcu_read_lock_sched / rcu_read_unlock_sched / synchronize_sched
instead of rcu_read_lock / rcu_read_unlock / synchronize_rcu.

This is an optimization. The RCU-protected region is very small, so
there will be no latency problems if we disable preempt in this region.

So we use rcu_read_lock_sched / rcu_read_unlock_sched that translates
to preempt_disable / preempt_disable. It is smaller (and supposedly
faster) than preemptible rcu_read_lock / rcu_read_unlock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch introduces new barrier pair light_mb() and heavy_mb() for
percpu rw semaphores.

This patch fixes a bug in percpu-rw-semaphores where a barrier was
missing in percpu_up_write.

This patch improves performance on the read path of
percpu-rw-semaphores: on non-x86 cpus, there was a smp_mb() in
percpu_up_read. This patch changes it to a compiler barrier and removes
the "#if defined(X86) ..." condition.

From: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 92063cee, it
was applied prematurely, causing this build error for
imx_v4_v5_defconfig:

arch/arm/mach-imx/clk-imx25.c: In function 'mx25_clocks_init':
arch/arm/mach-imx/clk-imx25.c:206:26: error: 'pwm_ipg_per' undeclared (first use in this function)
arch/arm/mach-imx/clk-imx25.c:206:26: note: each undeclared identifier is reported only once for each function it appears in

Sascha Hauer explains:
> There are several gates missing in clk-imx25.c. I have a patch which
> adds support for them and I seem to have missed that the above depends
> on it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

With the introduction of CONFIG_ARCH_MULTIPLATFORM, versatile is
no longer the default platform, so we need to enable
CONFIG_ARCH_VERSATILE explicitly in order for that to be selected
rather than the multiplatform configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The split of 370 and XP into two Kconfig options and the multiplatform
kernel support has changed a few Kconfig symbols, so let's update the
mvebu_defconfig file with the latest changes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

patch 738a0fd7 "ARM: at91: fix external interrupts in non-DT case"
fixed a run-time error on some at91 platforms but did not apply
the same change to at91x40, which now doesn't build.

This changes at91x40 in the same way that the other platforms
were changed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Pull networking fixes from David Miller:
 "This is what we usually expect at this stage of the game, lots of
  little things, mostly in drivers.  With the occasional 'oops didn't
  mean to do that' kind of regressions in the core code."

 1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann

 2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.

 3) Lost error code on return from _rtl_usb_receive(), from Christian
    Lamparter.

 4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.

 5) Release resources on error in pch_gbe driver, from Veaceslav Falico.

 6) Default hop limit not set correctly in ip6_template_metrics[], fix
    from Li RongQing.

 7) Gianfar PTP code requests wrong kind of resource during probe, fix
    from Wei Yang.

 8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.

 9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
    Shoua, Dotan Barak, and Uri Habusha.

10) usbnet leaks memory on TX path, fix from Hemant Kumar.

11) Use socket state test, rather than presence of FIN bit packet, to
    determine FIONREAD/SIOCINQ value.  Fix from Eric Dumazet.

12) Fix cxgb4 build failure, from Vipul Pandya.

13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
    info dumps.  From Yuchung Cheng.

14) Fix leak of security path in kfree_skb_partial().  Fix from Eric
    Dumazet.

15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
    Veaceslav Falico.

16) Fix MAINTAINERS file pattern for networking drivers, from Jean
    Delvare.

17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.

18) VLAN device type change restriction is too strict, and should not
    trigger for the automatically generated vlan0 device.  Fix from Jiri
    Pirko.

19) Make PMTU/redirect flushing work properly again in ipv4, from
    Steffen Klassert.

20) Fix memory corruptions by using kfree_rcu() in netlink_release().
    From Eric Dumazet.

21) More qmi_wwan device IDs, from Bjørn Mork.

22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
    infrastructure, from Elison Niven.

23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
  tilegx: fix some issues in the SW TSO support
  qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
  net: usb: Fix memory leak on Tx data path
  net/mlx4_core: Unmap UAR also in the case of error flow
  net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
  net/mlx4_en: Fix double-release-range in tx-rings
  bas_gigaset: fix pre_reset handling
  vhost: fix mergeable bufs on BE hosts
  gianfar_ptp: use iomem, not ioports resource tree in probe
  ipv6: Set default hoplimit as zero.
  NET_VENDOR_TI: make available for am33xx as well
  pch_gbe: fix error handling in pch_gbe_up()
  b43: Fix oops on unload when firmware not found
  mwifiex: clean up scan state on error
  mwifiex: return -EBUSY if specific scan request cannot be honored
  brcmfmac: fix potential NULL dereference
  Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
  ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
  rt2x00: usb: fix reset resume
  rtlwifi: pass rx setup error code to caller
  ...

Pull slave-dmaengine fixes from Vinod Koul:
 "Three fixes for slave dmanegine.

  Two are for typo omissions in sifr dmaengine driver and the last one
  is for the imx driver fixing a missing unlock"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: sirf: fix a typo in moving running dma_desc to active queue
  dmaengine: sirf: fix a typo in dma_prep_interleaved
  dmaengine: imx-dma: fix missing unlock on error in imxdma_xfer_desc()

Pull power management and ACPI fixes from Rafael J Wysocki:

 - Fix for a memory leak in acpi_bind_one() from Jesper Juhl.

 - Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
   from Jonghwan Choi.

 - Fix for smp_processor_id() usage in preemptible code in powernow-k8
   from Andreas Herrmann.

 - Fix for a suspend-related memory leak in cpufreq stats from Xiaobing
   Tu.

 - Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD in
   flush_old_exec() from Oleg Nesterov.

 - acpi_processor_notify() fix from Alan Cox.

* tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: missing break
  freezer: exec should clear PF_NOFREEZE along with PF_KTHREAD
  Fix memory leak in cpufreq stats.
  cpufreq / powernow-k8: Remove usage of smp_processor_id() in preemptible code
  PM / Domains: Fix memory leak on error path in pm_genpd_attach_cpuidle
  ACPI: Fix memory leak in acpi_bind_one()

Pull infiniband fixes from Roland Dreier:
 "Small batch of fixes for 3.7:
   - Fix crash in error path in cxgb4
   - Fix build error on 32 bits in mlx4
   - Fix SR-IOV bugs in mlx4"

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  mlx4_core: Perform correct resource cleanup if mlx4_QUERY_ADAPTER() fails
  mlx4_core: Remove annoying debug messages from SR-IOV flow
  RDMA/cxgb4: Don't free chunk that we have failed to allocate
  IB/mlx4: Synchronize cleanup of MCGs in MCG paravirtualization
  IB/mlx4: Fix QP1 P_Key processing in the Primary Physical Function (PPF)
  IB/mlx4: Fix build error on platforms where UL is not 64 bits

Pull USB fixes from Greg Kroah-Hartman:
 "Here are a bunch of USB fixes for the 3.7-rc tree.

  There's a lot of small USB serial driver fixes, and one larger one
  (the mos7840 driver changes are mostly just moving code around to fix
  problems.) Thanks to Johan Hovold for finding the problems and fixing
  them all up.

  Other than those, there is the usual new device ids, xhci bugfixes,
  and gadget driver fixes, nothing out of the ordinary.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'usb-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (49 commits)
  xhci: trivial: Remove assigned but unused ep_ctx.
  xhci: trivial: Remove assigned but unused slot_ctx.
  xhci: Fix missing break in xhci_evaluate_context_result.
  xhci: Fix potential NULL ptr deref in command cancellation.
  ehci: Add yet-another Lucid nohandoff pci quirk
  ehci: fix Lucid nohandoff pci quirk to be more generic with BIOS versions
  USB: mos7840: fix port_probe flow
  USB: mos7840: fix port-data memory leak
  USB: mos7840: remove invalid disconnect handling
  USB: mos7840: remove NULL-urb submission
  USB: qcserial: fix interface-data memory leak in error path
  USB: option: fix interface-data memory leak in error path
  USB: ipw: fix interface-data memory leak in error path
  USB: mos7840: fix port-device leak in error path
  USB: mos7840: fix urb leak at release
  USB: sierra: fix port-data memory leak
  USB: sierra: fix memory leak in probe error path
  USB: sierra: fix memory leak in attach error path
  USB: usb-wwan: fix multiple memory leaks in error paths
  USB: keyspan: fix NULL-pointer dereferences and memory leaks
  ...

Pull serial fix from Greg Kroah-Hartman:
 "Here is one patch, a revert of a omap serial driver patch that was
  causing problems, for your 3.7-rc tree.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'tty-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "serial: omap: fix software flow control"

Pull staging driver fixes from Greg Kroah-Hartman:
 "Here are some staging driver fixes for your 3.7-rc tree.

  Nothing major here, a number of iio driver fixups that were causing
  problems, some comedi driver bugfixes, and a bunch of tidspbridge
  warning squashing and other regressions fixed from the 3.6 release.

  All have been in the linux-next releases for a bit.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'staging-3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (32 commits)
  staging: tidspbridge: delete unused mmu functions
  staging: tidspbridge: ioremap physical address of the stack segment in shm
  staging: tidspbridge: ioremap dsp sync addr
  staging: tidspbridge: change type to __iomem for per and core addresses
  staging: tidspbridge: drop const from custom mmu implementation
  staging: tidspbridge: request the right irq for mmu
  staging: ipack: add missing include (implicit declaration of function 'kfree')
  staging: ramster: depends on NET
  staging: omapdrm: fix allocation size for page addresses array
  staging: zram: Fix handling of incompressible pages
  Staging: android: binder: Allow using highmem for binder buffers
  Staging: android: binder: Fix memory leak on thread/process exit
  staging: comedi: ni_labpc: fix possible NULL deref during detach
  staging: comedi: das08: fix possible NULL deref during detach
  staging: comedi: amplc_pc263: fix possible NULL deref during detach
  staging: comedi: amplc_pc236: fix possible NULL deref during detach
  staging: comedi: amplc_pc236: fix invalid register access during detach
  staging: comedi: amplc_dio200: fix possible NULL deref during detach
  staging: comedi: 8255_pci: fix possible NULL deref during detach
  staging: comedi: ni_daq_700: fix dio subdevice regression
  ...

Pull driver core fixes from Greg Kroah-Hartman:
 "Here are a number of firmware core fixes for 3.7, and some other minor
  fixes.  And some documentation updates thrown in for good measure.

  All have been in the linux-next tree for a while.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  Documentation:Chinese translation of Documentation/arm64/memory.txt
  Documentation:Chinese translation of Documentation/arm64/booting.txt
  Documentation:Chinese translation of Documentation/IRQ.txt
  firmware loader: document kernel direct loading
  sysfs: sysfs_pathname/sysfs_add_one: Use strlcat() instead of strcat()
  dynamic_debug: Remove unnecessary __used
  firmware loader: sync firmware cache by async_synchronize_full_domain
  firmware loader: let direct loading back on 'firmware_buf'
  firmware loader: fix one reqeust_firmware race
  firmware loader: cancel uncache work before caching firmware

Pull char/misc driver fixes from Greg Kroah-Hartman:
 "Here are some driver fixes for 3.7.  They include extcon driver fixes,
  a hyper-v bugfix, and two other minor driver fixes.

  All of these have been in the linux-next releases for a while.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'char-misc-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  sonypi: suspend/resume callbacks should be conditionally compiled on CONFIG_PM_SLEEP
  Drivers: hv: Cleanup error handling in vmbus_open()
  extcon : register for cable interest by cable name
  extcon: trivial: kfree missed from remove path
  extcon: driver model release call not needed
  extcon: MAX77693: Add platform data for MUIC device to initialize registers
  extcon: max77693: Use max77693_update_reg for rmw operations
  extcon: Fix kerneldoc for extcon_set_cable_state and extcon_set_cable_state_
  extcon: adc-jack: Add missing MODULE_LICENSE
  extcon: adc-jack: Fix checking return value of request_any_context_irq
  extcon: Fix return value in extcon_register_interest()
  extcon: unregister compat link on cleanup
  extcon: Unregister compat class at module unload to fix oops
  extcon: optimising the check_mutually_exclusive function
  extcon: standard cable names definition and declaration changed
  extcon-max8997: remove usage of ret in max8997_muic_handle_charger_type_detach
  extcon: Remove duplicate inclusion of extcon.h header file