Registering the netdev before setting the priv data is unsafe.
So fix this possible race by setting the priv data first.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: <stable@vger.kernel.org> # v3.18+
Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>

When the bus id was supplied via a struct platform_device, the driver wasn't
handling -1 to mean an unspecified id of the only instance of this driver,
as the platform spec requires.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes an issue where the send(MSG_DONTWAIT) call
on a TX_RING is not fully non-blocking in cases where the device's sndBuf is
full. We pass nonblock=true to sock_alloc_send_skb() and return any possibly
occuring error code (most likely EGAIN) to the caller. As the fast-path stays
as it is, we keep the unlikely() around skb == NULL.
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 12a8541d "bnx2x: Delay during kdump load" added a 5 seconds
delay to bnx2x's probe function in the kdump case to let the firmware
realize the old driver is gone.

The problem with the delay is that it is per-device, so if you have
several bnx2x NICs in NPAR mode, the delays can accumulate to minutes.

Fix it by adjusting the delay so that we do not wait more than
necessary, i.e. no more delaying after 5 seconds of kernel boot time.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ARM: net: delegate filter to kernel interpreter when imm_offset() return value can't fit into 12bits.

The ARM JIT code emits "ldr rX, [pc, #offset]" to access the literal
pool. #offset maximum value is 4095 and if the generated code is too
large, the #offset value can overflow and not point to the expected
slot in the literal pool. Additionally, when overflow occurs, bits of
the overflow can end up changing the destination register of the ldr
instruction.

Fix that by detecting the overflow in imm_offset() and setting a flag
that is checked for each BPF instructions converted in
build_body(). As of now it can only be detected in the second pass. As
a result the second build_body() call can now fail, so add the
corresponding cleanup code in that case.

Using multiple literal pools in the JITed code is going to require
lots of intrusive changes to the JIT code (which would better be done
as a feature instead of fix), just delegating to the kernel BPF
interpreter in that case is a more straight forward, minimal fix and
easy to backport.

Fixes: ddecdfce ("ARM: 7259/3: net: JIT compiler for packet filters")
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

In that case, emit_udiv() will be called with rn == ARM_R0 (r_scratch)
and loading rm first into ARM_R0 will result in jit_udiv() function
being called the same dividend and divisor. Fix that by loading rn
first into ARM_R1 and then rm into ARM_R0.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Cc: <stable@vger.kernel.org> # v3.13+
Fixes: aee636c4 (bpf: do not use reciprocal divide)
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since these are now visible to userspace it is nice to be consistent
with BSD (sys/netmpls/mpls.h in netBSD).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-05-07

This series contains updates to igb only.

Toshiaki provides two fixes for igb, first fixes an issue when changing
the number of rings by ethtool which causes oops because of uninitialized
pointers.  The second fix resolves a typo where tx_ring was used instead
of the desired rx_ring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

transfer_buffer_length is of type u32. It's therefore wrong to assign it
to a signed integer. This patch avoids the overflow.

It's worth noting that entry->length here is a long; perhaps it would be
beneficial at somepoint to change this to be unsigned as well, if
nothing else relies on its signedness for error conditions or the like.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch should have been part of the previous patch having the
same summary. See  http://marc.info/?l=linux-kernel&m=143039470103795&w=2
Unfortunately, I didn't check to see where else this lock was used before
submitting that patch. This should take care of it for netxen_nic, as I
did a thorough search this time.

To recap from the original patch; although testing this driver with
DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled did not produce any traces,
it would be more prudent in the case of tx_clean_lock to use _bh
versions of spin_[un]lock, since this lock is manipulated in both
the process and softirq contexts.

This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Acked-By: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The xgene_enet driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Cc: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The amd-xgbe driver currently only works with the Seattle SoC, which
is ARM64 architecture, so there is no point in building this driver on
other architectures except for build testing purpose. The dependency
list can be updated later if the driver ever supports other
architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When tcf_destroy() returns true, tp could be already destroyed,
we should not use tp->next after that.

For long term, we probably should move tp list to list_head.

Fixes: 1e052be6 ("net_sched: destroy proto tp when all filters are gone")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This device is sold as 'Lenovo OneLink Pro Dock'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Vasily Titskiy <qehgt0@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same hardware issue the at91 must work around applies to at least the
Zynq ethernet, and possibly more devices.  The driver also needs to handle
the RXUBR interrupt since it turns it on with MACB_RX_INT_FLAGS anyway.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sowmini Varadhan says:

====================
net/rds: RDS-TCP robustness fixes

This patch-set contains bug fixes for state-recovery at the RDS
layer when the underlying transport is TCP and the TCP state at one
of the endpoints is reset

V2 changes: DaveM comments to reduce memory footprint, follow
            NFS/RPC model where possible. Added test-case #3

Without the changes in this set, when one of the endpoints is reset,
the existing code does not correctly clean up RDS socket state for stale
connections, resulting in some unstable, timing-dependant behavior on
the wire, including an infinite exchange of 3WHs back-and-forth, and a
resulting potential to never converge RDS state.

Test cases used to verify the changes in this set are:

1. Start rds client/server applications on two participating nodes,
   node1 and node2. After at least one packet has been sent (to establish
   the TCP connection), restart the rds_tcp module on the client, and
   now resend packets. Tcpdump should show server sending a FIN for the
   "old" client port, and clean connection establishment/exchange for
   the new client port.

2. At the end of step 1, restart rds srever on node2, and start client on
   node1, make sure using tcpdump, 'netstat -an|grep 16385' that
   packets flow correctly.

3. start RDS client/server application on two participating nodes, and
   repeat steps 1 and 2, but this time, simulate node failure by doing
   "ifconfig <intf> down", so no FIN is sent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When the peer of an RDS-TCP connection restarts, a reconnect
attempt should only be made from the active side  of the TCP
connection, i.e. the side that has a transient TCP port
number. Do not add the passive side of the TCP connection
to the c_hash_node and thus avoid triggering rds_queue_reconnect()
for passive rds connections.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running RDS over TCP, the active (client) side connects to the
listening ("passive") side at the RDS_TCP_PORT.  After the connection
is established, if the client side reboots (potentially without even
sending a FIN) the server still has a TCP socket in the esablished
state.  If the server-side now gets a new SYN comes from the client
with a different client port, TCP will create a new socket-pair, but
the RDS layer will incorrectly pull up the old rds_connection (which
is still associated with the stale t_sock and RDS socket state).

This patch corrects this behavior by having rds_tcp_accept_one()
always create a new connection for an incoming TCP SYN.
The rds and tcp state associated with the old socket-pair is cleaned
up via the rds_tcp_state_change() callback which would typically be
invoked in most cases when the client-TCP sends a FIN on TCP restart,
triggering a transition to CLOSE_WAIT state. In the rarer event of client
death without a FIN, TCP_KEEPALIVE probes on the socket will detect
the stale socket, and the TCP transition to CLOSE state will trigger
the RDS state cleanup.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there are only IPv6 source specific default routes present, the
host gets -ENETUNREACH on e.g. connect() because ip6_dst_lookup_tail
calls ip6_route_output first, and given source address any, it fails,
and ip6_route_get_saddr is never called.

The change is to use the ip6_route_get_saddr, even if the initial
ip6_route_output fails, and then doing ip6_route_output _again_ after
we have appropriate source address available.

Note that this is '99% fix' to the problem; a correct fix would be to
do route lookups only within addrconf.c when picking a source address,
and never call ip6_route_output before source address has been
populated.
Signed-off-by: Markus Stenberg <markus.stenberg@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
Here are a couple of important Bluetooth & mac802154 fixes for 4.1:

 - mac802154 fix for crypto algorithm allocation failure checking
 - mac802154 wpan phy leak fix for error code path
 - Fix for not calling Bluetooth shutdown() if interface is not up

Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

adapter->tx_ring is set to NULL where rx_ring should be.

Fixes: 5536d210 ("igb: Combine q_vector and ring allocation into a single function")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When changing the number of rings by ethtool -L, q_vectors are reused,
which causes oops because of uninitialized pointers.

- When an rx is reused as a tx, q_vector->rx.ring is not set to NULL, which
  misleads igb_poll() to determine that it has an rx ring although it
  actually points to the tx ring.
- When a tx is reused as an rx, q_vector->rx.ring->skb
  (q_vector->ring[0].skb) has a value that was used as tx_stats before.

Fix these problems by zeroing it out on reuseing it.

Fixes: 02ef6e1d ("igb: Fix queue allocation method to accommodate changing during runtime")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

I forgot to update tcp_westwood when changing get_info() behavior,
this patch should fix this.

Fixes: 64f40ff5 ("tcp: prepare CC get_info() access from getsockopt()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-05-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
iwlwifi:

* fix firmware API for -13.ucode
* fix RSSI handling that avoid bad roaming decision
* fix firmware debug
* fix MFUART operation
* fix ASSERT while restart the hardware (because of another ASSERT e.g)

ath9k:

* fix per-packet tx power configuration

rtlwifi:

* rtl8192cu: Fix kernel deadlock
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Move to include/uapi/linux/mpls.h to be externally visibile.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 fixes for 4.1-rc2

Eran's fix is for a small off-by-one introduces on 4.1-rc1.

Yisahi fixes an issue with comes into play only on VMs with
many (> 256) vCPUs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The Firmware uses dynamic EQs allocation based on number of VFs and
max EQs that can be allocated. As a result, VF can have EQ numbers
that are larger than 256.

According to the firmware spec, the max value is limited to be 1024
(10 bits), adapt the relevant code accordingly. This bug was impossible
to hit prior to commit 7ae0e400 ("net/mlx4_core: Flexible (asymmetric)
allocation of EQs and MSI-X vectors for PF/VFs") which actually enables
large number of EQs for VFs.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This caused the en_stats_adder helper to accumulate a field which is
not related to the counter, fix that.

Fixes: a3333b35 ('net/mlx4_en: Moderate ethtool callback to show [..]')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With commit b56fc3c5 ("hv_netvsc: Fix a bug in netvsc_start_xmit()"),
skb variable is no longer used in netvsc_send. Remove variable and dead
code that depended on it.

Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2015-05-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
We have only a few fixes right now:
 * a fix for an issue with hash collision handling in the
   rhashtable conversion
 * a merge issue - rhashtable removed default shrinking
   just before mac80211 was converted, so enable it now
 * remove an invalid WARN that can trigger with legitimate
   userspace behaviour
 * add a struct member missing from kernel-doc that caused
   a lot of warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Submit 909d9faa ("bnx2x: Prevent inner-reload while VFs exist")
contained a bug - MTU change was not prevented by it; Instead, it
`randomally' prevented bnx2x_resume() from running [harmless yet wrong].

This moves the check to its correct spot.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2015-05-04

Here's the first bluetooth-next pull request for 4.2:

 - Various fixes for at86rf230 driver
 - ieee802154: trace events support for rdev->ops
 - HCI UART driver refactoring
 - New Realtek IDs added to btusb driver
 - Off-by-one fix for rtl8723b in btusb driver
 - Refactoring of btbcm driver for both UART & USB use

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

c0adf54a introduced new sparse warnings:
  CHECK   /home/dahern/kernels/linux.git/net/rds/ib_cm.c
net/rds/ib_cm.c:191:34: warning: incorrect type in initializer (different base types)
net/rds/ib_cm.c:191:34:    expected unsigned long long [unsigned] [usertype] dp_ack_seq
net/rds/ib_cm.c:191:34:    got restricted __be64 <noident>
net/rds/ib_cm.c:194:51: warning: cast to restricted __be64

The temporary variable for sequence number should have been declared as __be64
rather than u64. Make it so.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Cc: shamir rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 8d7d9cca.

Now that the necessary infrastructure is really all there
in the tree, we can put this change back in.
Signed-off-by: David S. Miller <davem@davemloft.net>

When smsc911x uses GPIO as the interrupt controller, and if both are
loaded as modules, we get following error:

"smsc911x: Could not allocate irq resource"

This issue is because of smsc911x using platform_get_resource to get
device tree based irq resource.

commit "9ec36caf (of/irq: do irq resolution in platform_get_irq)" and
commit "7085a7 (drivers: platform: parse IRQ flags from resources)" add
support in platform_get_irq to resolve irq and irq_flags respectively
for both modern device tree and legacy static platform data platforms.

Modify smsc911x driver to use platform_get_irq to pick up irq resource
correctly and use irq_get_trigger_type to get the IRQ trigger flags.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code in __netdev_upper_dev_link() has an over-stringent
loop detection logic that actually prevents valid configurations
from working correctly.

In particular, the logic returns an error if an upper device
is already in the list of all upper devices for a given dev.
This particular check seems to be a overzealous as it disallows
perfectly valid configurations.  For example:
  # ip l a link eth0 name eth0.10 type vlan id 10
  # ip l a dev br0 typ bridge
  # ip l s eth0.10 master br0
  # ip l s eth0 master br0  <--- Will fail

If you switch the last two commands (add eth0 first), then both
will succeed.  If after that, you remove eth0 and try to re-add
it, it will fail!

It appears to be enough to simply check adj_list to keeps things
safe.

I've tried stacking multiple devices multiple times in all different
combinations, and either rx_handler registration prevented the stacking
of the device linking cought the error.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As German phone operators are discontinuing ISDN service, neither
Hansjörg nor I will be able to maintain the Gigaset ISDN drivers
any longer. Paul Bolle offered to step into the breach for odd
fixes.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate 90 of these warnings:

Warning(..//include/net/mac80211.h:1682): No description found for parameter 'drv_priv[0]'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When a macvlan device is placed in promiscuous mode, it currently
just sets it's multicast mask to permissive, but doesn't change
the state of the lower device.  As a result, not all multicast
traffic can be received on such device.  Additionally, none of
a vlan traffic can be received on such device as well.
This patch propagates the promiscuous mode setting to lower device
so that lower device may receive all packets that macvlan may
be interested in.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit c243d7e2.

That patch is solving a non-existant problem while creating a
real problem.  Just because a socket is allocated in the init
name space doesn't mean that it gets hashed in the init name space.

When we unhash it the name space must be the same as the one
we had when we hashed it.  So this patch is completely bogus
and causes socket leaks.
Reported-by: Andrey Wagin <avagin@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>