- unify vlan and nonvlan rx path
- kill adapter->vlgrp and atl1e_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill adapter->vlgrp and atl1c_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill lp->vlgrp and amd8111e_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- remove useless vlan parameters and pointers
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

no longer used
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill port->vgrp and ehea_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill nesvnic->vlan_grp and nes_netdev_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since vlan_group_get_device and vlan_group is not going to be accessible
from device drivers, introduce function which substitutes it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

else case remained forgotten.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/bluetooth/l2cap_core.c

An implementation of a code generator for BPF programs to speed up packet
filtering on PPC64, inspired by Eric Dumazet's x86-64 version.

Filter code is generated as an ABI-compliant function in module_alloc()'d mem
with stackframe & prologue/epilogue generated if required (simple filters don't
need anything more than an li/blr).  The filter's local variables, M[], live in
registers.  Supports all BPF opcodes, although "complicated" loads from negative
packet offsets (e.g. SKF_LL_OFF) are not yet supported.

There are a couple of further optimisations left for future work; many-pass
assembly with branch-reach reduction and a register allocator to push M[]
variables into volatile registers would improve the code quality further.

This currently supports big-endian 64-bit PowerPC only (but is fairly simple
to port to PPC32 or LE!).

Enabled in the same way as x86-64:

	echo 1 > /proc/sys/net/core/bpf_jit_enable

Or, enabled with extra debug output:

	echo 2 > /proc/sys/net/core/bpf_jit_enable
Signed-off-by: Matt Evans <matt@ozlabs.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

so that ethtool -i will display it correctly on big endian systems.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bnx2fc driver needs to handle netdev events on VLAN devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise, the firmware will not respond and we'll have to wait for
timeout.  Refactor the wait loop we already have into a separate
function for this purpose.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Include FCoE CID space only for E2_PLUS devices.  Remove old CID
offset adjustments that are no longer needed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes NVRAM selftest failures for 5720 devices by fixing the
checksum area size.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer VPD datablocks can exceed the size the tg3 driver is traditionally
used to.  This can cause some of the routines that operate on the VPD
data to fail when in-fact they could have succeeded had they known the
correct size.  This patch fixes the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes interrupt selftest failures for recent devices (57765,
5717, 5718. 5719, 5720) by disabling MSI one-shot mode and applying the
status tag workaround to the selftest code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current RSS indirection table is populated such that more traffic
will hit the first RSS ring.  This patch adjusts the indirection table
so that the load is more evenly distributed.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the 5719 and the 5720 to the list of devices that are
EEE capable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Occasionally, when the network cable is removed after a successful
autonegotiation, the device will not send a link down interrupt to the
driver.  This happens because of a bad interaction of an EEE
workaround.  The fix is to adjust the code so that the root cause
condition does not happen.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch increases the scope of the EEE interoperability workaround
to include more asic revisions.  The workarond value is tuned to
workaround a link flap issue at 100Mbps.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit f2096f94, entitled
"tg3: Add 5720 H2BMC support", needed to add code to preserve some bits
set by firmware.  Unfortunately the new code causes throughput to stop
after a chip reset because it enables state machines before they are
ready.  This patch undoes the problematic code.  The bits will be
restored later in the init sequence.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes both the failure in the self-test on 578xx
and a hole in a parity recovery flow that this failure
has discovered:
 - internal 'pending' state in a VLAN_MAC object wasn't been cleared
when the object state change was called with DRV_ONLY flag, which in
particular happens when a parity error happens during the self-test.
 - bp->sp_state wasn't cleared in the similar circumstances as described
above.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the parity errors recovery flow for 578xx:
    - Add a separate column for the 578xx in the parity mask
      registers DB.
    - Fix the bnx2x_process_kill_chip_reset() to handle the blocks
      newly introduced in the 578xx.

Cover ATC and PGLUE_B blocks for 57712 and 578xx.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Read FIP MAC address from SHMEM's "port" section
similar to what we do in a MF mode when we read it from
a "func" section of SHMEM.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Registers dump code erroneously treated 578xx as 57712.
This patch fixes the above and also removes unused data
structures.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some gcc versions warn about prototypes without "inline" when the declaration
includes the "inline" keyword. The fix generates a false error message
"marked inline, but without a definition" with sparse below 0.4.2.
Signed-off-by: Chris Friesen <chris.friesen@genband.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>

If overlapping networks with different interfaces was added to
the set, the type did not handle it properly. Example

    ipset create test hash:net,iface
    ipset add test 192.168.0.0/16,eth0
    ipset add test 192.168.0.0/24,eth1

Now, if a packet was sent from 192.168.0.0/24,eth0, the type returned
a match.

In the patch the algorithm is fixed in order to correctly handle
overlapping networks.

Limitation: the same network cannot be stored with more than 64 different
interfaces in a single set.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: fix file mode calculation

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  davinci: DM365 EVM: fix video input mux bits
  ARM: davinci: Check for NULL return from irq_alloc_generic_chip
  arm: davinci: Fix low level gpio irq handlers' argument

I'm running a workload which triggers a lot of swap in a machine with 4
nodes.  After I kill the workload, I found a kswapd livelock.  Sometimes
kswapd3 or kswapd2 are keeping running and I can't access filesystem,
but most memory is free.

This looks like a regression since commit 08951e54 ("mm: vmscan:
correct check for kswapd sleeping in sleeping_prematurely").

Node 2 and 3 have only ZONE_NORMAL, but balance_pgdat() will return 0
for classzone_idx.  The reason is end_zone in balance_pgdat() is 0 by
default, if all zones have watermark ok, end_zone will keep 0.

Later sleeping_prematurely() always returns true.  Because this is an
order 3 wakeup, and if classzone_idx is 0, both balanced_pages and
present_pages in pgdat_balanced() are 0.  We add a special case here.
If a zone has no page, we think it's balanced.  This fixes the livelock.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Assume that /sys/kernel/debug/dummy64 is debugfs file created by
debugfs_create_x64().

	# cd /sys/kernel/debug
	# echo 0x1234567812345678 > dummy64
	# cat dummy64
	0x0000000012345678

	# echo 0x80000000 > dummy64
	# cat dummy64
	0xffffffff80000000

A value larger than INT_MAX cannot be written to the debugfs file created
by debugfs_create_u64 or debugfs_create_x64 on 32bit machine.  Because
simple_attr_write() uses simple_strtol() for the conversion.

To fix this, use simple_strtoll() instead.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  vfs: fix race in rcu lookup of pruned dentry
  Fix cifs_get_root()

[ Edited the last commit to get rid of a 'unused variable "seq"'
  warning due to Al editing the patch.  - Linus ]

Don't update *inode in __follow_mount_rcu() until we'd verified that
there is mountpoint there.  Kudos to Hugh Dickins for catching that
one in the first place and eventually figuring out the solution (and
catching a braino in the earlier version of patch).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>