We can overflow the hardirq stack if we set the %pil here
so early, just let the normal control flow do it.

This is fine as we are allowed to do the actual IRQ enable
at any point after we call trace_hardirqs_on.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

It currently overlaps the NMI bit.
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise we can overflow the main stack with the function tracer
enabled.
Signed-off-by: David S. Miller <davem@davemloft.net>

128 bytes is sufficient for the register window save area, but the
calling conventions allow the callee to save up to 6 incoming argument
registers into the stack frame after the register window save area.

This means a minimal stack frame is 176 bytes (128 + (6 * 8)).

This fixes random crashes when using the function tracer.
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix forgotten kmemleak headers inclusion for kmemleak_not_leak()
declaration.

This fixes the following build error:

	arch/sparc/kernel/irq_64.c: In function ‘sun4v_build_virq’:
	arch/sparc/kernel/irq_64.c:657: error: implicit declaration of function ‘kmemleak_not_leak’
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suggested by Peter Zijlstra
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	lib/Kconfig.debug

Found by kmemleak.

If request_resource() fails, we leak the struct resource we
allocated to represent the IOMMU mapping area.

This actually happens on sun4v machines because the IOMEM area is only
reported sans the IOMMU region, unlike all previous systems.  I'll
need to fix that at some point, but for now fix the leak.
Signed-off-by: David S. Miller <davem@davemloft.net>

The only reference we store to this memory is in the form of a
physical address, so kmemleak can't see it.

Add a kmemleak_not_leak() annotation.

It's probably useful to be able to look at a dump of these things
either via debugfs or similar, and thus we could at some point store
them in some kind of table and therefore get rid of this annotation.
Signed-off-by: David S. Miller <davem@davemloft.net>

Only missing thing was an _sdata marker in vmlinux.lds.S
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

It's the only way we'll be able to implement the function
graph tracer properly.

A positive is that we no longer have to worry about the
linker over-optimizing the tail call, since we don't
use a tail call any more.
Signed-off-by: David S. Miller <davem@davemloft.net>

This keeps us from having to use kstat_irqs_cpu() from the NMI handler,
the former of which is a profiled function.

Instead we use a currently empty slot in the cpu_data
Signed-off-by: David S. Miller <davem@davemloft.net>

These include the timer implementation, perf events support, and the
performance counter register (pcr) programming layer.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

The generic stack tracer does this job just as well.
Signed-off-by: David S. Miller <davem@davemloft.net>

Check function_trace_stop at ftrace_caller

Toss mcount_call and dummy call of ftrace_stub, unnecessary.

Document problems we'll have if the final kernel image link
ever turns on relaxation.

Properly size 'ftrace_call' so it looks right when inspecting
instructions under gdb et al.
Signed-off-by: David S. Miller <davem@davemloft.net>

If we are in an NMI then doing a plain raw_local_irq_disable() will
write PIL_NORMAL_MAX into %pil, which is lower than PIL_NMI, and thus
we'll re-enable NMIs and recurse.

Doing a simple:

	%pil = %pil | PIL_NORMAL_MAX

does what we want, if we're already at PIL_NMI (15) we leave it at
that setting, else we set it to PIL_NORMAL_MAX (14).

This should get the function tracer working on sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>

This gets rid of a local function (is_kernel_stack()) which tries to
do the same thing, yet poorly in that it doesn't handle IRQ stacks
properly.
Signed-off-by: David S. Miller <davem@davemloft.net>

* anonvma:
  anonvma: when setting up page->mapping, we need to pick the _oldest_ anonvma
  anon_vma: clone the anon_vma chain in the right order
  vma_adjust: fix the copying of anon_vma chains
  Simplify and comment on anon_vma re-use for anon_vma_prepare()

* master.kernel.org:/home/rmk/linux-2.6-arm: (21 commits)
  ARM: Fix ioremap_cached()/ioremap_wc() for SMP platforms
  ARM: 6043/1: AT91 slow-clock resume: Don't wait for a disabled PLL to lock
  ARM: 6031/1: fix Thumb-2 decompressor
  ARM: 6029/1: ep93xx: gpio.c: local functions should be static
  ARM: 6028/1: ARM: add MAINTAINERS for U300
  ARM: 6024/1: bcmring: fix missing down on semaphore in dma.c
  MXC: mach_armadillo5x0: Add USB Host support.
  ARM mach-mx3: duplicated include
  ARM mach-mx3: duplicated include
  imx31: add watchdog device on litekit board.
  imx3: Add watchdog platform device support
  MXC: mach-mx31_3ds: add support for freescale mc13783 power management device.
  MXC: mach-mx31_3ds: Add SPI1 device support.
  MXC: mach-mx31_3ds: Add support for on board NAND Flash.
  MXC: mach-mx31_3ds: Update variable names over recent mach name modification.
  imx31: fix parent clock for rtc
  i.MX51: remove NFC AXI static mapping
  i.MX51: determine silicon revision dynamically
  i.MX51: map TZIC dynamically
  i.MX51: Use correct clock for gpt
  ...

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: make sure the chunk allocator doesn't create zero length chunks
  Btrfs: fix data enospc check overflow

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  quota: Fix possible dq_flags corruption
  quota: Hide warnings about writes to the filesystem before quota was turned on
  ext3: symlink must be handled via filesystem specific operation
  ext2: symlink must be handled via filesystem specific operation

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
  udf: add speciffic ->setattr callback
  udf: potential integer overflow

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (36 commits)
  MIPS: Calculate proper ebase value for 64-bit kernels
  MIPS: Alchemy: DB1200: Remove custom wait implementation
  MIPS: Big Sur: Make defconfig more useful.
  MIPS: Fix __vmalloc() etc. on MIPS for non-GPL modules
  MIPS: Sibyte: Fix M3 TLB exception handler workaround.
  MIPS: BCM63xx: Fix build failure in board_bcm963xx.c
  MIPS: uasm: Add OR instruction.
  MIPS: Sibyte: Apply M3 workaround only on affected chip types and versions.
  MIPS: BCM63xx: Initialize gpio_out_low & out_high to current value at boot.
  MIPS: BCM63xx: Register SSB SPROM fallback in board's first stage callback
  MIPS: BCM63xx: Fix typo in cpu-feature-overrides file.
  MIPS: BCM63xx: Add support for second uart.
  MIPS: BCM63xx: Fix double gpio registration.
  MIPS: BCM63xx: Add DWVS0 board
  MIPS: BCM63xx: Add the RTA1025W-16 BCM6348-based board to suppported boards.
  MIPS: BCM63xx: Fix BCM6338 and BCM6345 gpio count
  MIPS: libgcc.h: Checkpatch cleanup
  MIPS: Loongson-2F: Flush the branch target history in BTB and RAS
  MIPS: Move signal trampolines off of the stack.
  MIPS: Preliminary VDSO
  ...

* 'for-2.6.34' of git://linux-nfs.org/~bfields/linux:
  svcrdma: RDMA support not yet compatible with RPC6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix typo "numer" -> "number" in alloc.c
  nilfs2: Remove an uninitialization warning in nilfs_btree_propagate_v()
  nilfs2: fix a wrong type conversion in nilfs_ioctl()

Otherwise we might be mapping in a page in a new mapping, but that page
(through the swapcache) would later be mapped into an old mapping too.
The page->mapping must be the case that works for everybody, not just
the mapping that happened to page it in first.

Here's the scenario:

 - page gets allocated/mapped by process A. Let's call the anon_vma we
   associate the page with 'A' to keep it easy to track.

 - Process A forks, creating process B. The anon_vma in B is 'B', and has
   a chain that looks like 'B' -> 'A'. Everything is fine.

 - Swapping happens. The page (with mapping pointing to 'A') gets swapped
   out (perhaps not to disk - it's enough to assume that it's just not
   mapped any more, and lives entirely in the swap-cache)

 - Process B pages it in, which goes like this:

        do_swap_page ->
          page = lookup_swap_cache(entry);
         ...
          set_pte_at(mm, address, page_table, pte);
          page_add_anon_rmap(page, vma, address);

   And think about what happens here!

   In particular, what happens is that this will now be the "first"
   mapping of that page, so page_add_anon_rmap() used to do

        if (first)
                __page_set_anon_rmap(page, vma, address);

   and notice what anon_vma it will use? It will use the anon_vma for
   process B!

   What happens then? Trivial: process 'A' also pages it in (nothing
   happens, it's not the first mapping), and then process 'B' execve's
   or exits or unmaps, making anon_vma B go away.

   End result: process A has a page that points to anon_vma B, but
   anon_vma B does not exist any more.  This can go on forever.  Forget
   about RCU grace periods, forget about locking, forget anything like
   that.  The bug is simply that page->mapping points to an anon_vma
   that was correct at one point, but was _not_ the one that was shared
   by all users of that possible mapping.

Changing it to always use the deepest anon_vma in the anonvma chain gets
us to the safest model.

This can be improved in certain cases: if we know the page is private to
just this particular mapping (for example, it's a new page, or it is the
only swapcache entry), we could pick the top (most specific) anon_vma.

But that's a future optimization. Make it _work_ reliably first.
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Borislav Petkov <bp@alien8.de> [ "What do you know, I think you fixed it!" ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We want to walk the chain in reverse order when cloning it, so that the
order of the result chain will be the same as the order in the source
chain.  When we add entries to the chain, they go at the head of the
chain, so we want to add the source head last.
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Borislav Petkov <bp@alien8.de> [ "No, it still oopses" ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When we move the boundaries between two vma's due to things like
mprotect, we need to make sure that the anon_vma of the pages that got
moved from one vma to another gets properly copied around.  And that was
not always the case, in this rather hard-to-follow code sequence.

Clarify the code, and fix it so that it copies the anon_vma from the
right source.
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Borislav Petkov <bp@alien8.de> [ "Yeah, not so much this one either" ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This changes the anon_vma reuse case to require that we only reuse
simple anon_vma's - ie the case when the vma only has a single anon_vma
associated with it.

This means that a reuse of an anon_vma from an adjacent vma will always
guarantee that both vma's are associated not only with the same
anon_vma, they will also have the same anon_vma chain (of just a single
entry in this case).

And since anon_vma re-use was the only case where the same anon_vma
might be associated with different chains of anon_vma's, we now have the
case that every vma that shares the same anon_vma will always also have
the same chain.  That makes it much easier to think about merging vma's
that share the same anon_vma's: you can always just drop the other
anon_vma chain in anon_vma_merge() since you know that they are always
identical.

This also splits up the function to validate the anon_vma re-use, and
adds a lot of commentary about the possible races.
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Borislav Petkov <bp@alien8.de> [ "That didn't fix it" ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

dq_flags are modified non-atomically in do_set_dqblk via __set_bit calls and
atomically for example in mark_dquot_dirty or clear_dquot_dirty.  Hence a
change done by an atomic operation can be overwritten by a change done by a
non-atomic one. Fix the problem by using atomic bitops even in do_set_dqblk.
Signed-off-by: Andrew Perepechko <andrew.perepechko@sun.com>
Signed-off-by: Jan Kara <jack@suse.cz>

For a root filesystem write to the filesystem before quota is turned on happens
regularly and there's no way around it because of writes to syslog, /etc/mtab,
and similar. So the warning is rather pointless for ordinary users. It's
still useful during development so we just hide the warning behind
__DQUOT_PARANOIA config option.
Signed-off-by: Jan Kara <jack@suse.cz>

generic setattr implementation is no longer responsible for
quota transfer so synlinks must be handled via ext3_setattr.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>

generic setattr implementation is no longer responsible for
quota transfer so synlinks must be handled via ext2_setattr.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>

The ebase is relative to CKSEG0 not CAC_BASE.  On a 32-bit kernel they
are the same thing, for a 64-bit kernel they are not.

It happens to kind of work on a 64-bit kernel as they both reference
the same physical memory.  However since the CPU uses the CKSEG0 base,
determining if a J instruction will reach always gives the wrong result
unless we use the same number the CPU uses.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1093/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

While playing with the out-of-tree MAE driver module, the system would
panic after a while in the db1200 custom wait code after wakeup due to
a clobbered k0 register being used as target address of a store op.

Remove the custom wait implementation and revert back to the Alchemy-
recommended implementation already set as default.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1092/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>