When applying commit 7d26b587 (fix failure path in
dwc3_pci_probe()), I mistakenly left out one of the
possible failures where we would return success even
on the error case.

This patch fixes that mistake.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Non-hub device has no child, and even a real USB hub has ports far
less than USB_MAXCHILDREN, so there is no need using a fix array for
child devices, just allocate it dynamically according real port
number.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-usb-next-2012-03-13' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next

Hi Greg,

Here's my final pull request for 3.4.  All the patches have been under
review for some time (months in some cases).  The ring expansion patches
in particular have been tested by both me and Paul Zimmerman from
Synopsis.

They add support for:
 - Dynamic ring expansion
 - New USB 2.1 link PM errata (BESL)
 - xHCI host controller support for the Synopsis DesignWare 3 IP

The dynamic ring expansion patches finally make test 10 of the host-side
test pass, instead of failing due to no room on the endpoint ring for
the larger transfers.  I would have hoped that the ring expansion
patchset would make the Point Grey USB 3.0 camera work, but sadly it
fails to respond to a control transfer on my test system.  This doesn't
seem to be a driver bug, but it could be a device or host bug.

Felipe has tested the patches to add a platform device to the xHCI
driver on the Synopsis DesignWare 3 IP in the TI OMAP5 board.

Please pull.

Thanks,
Sarah Sharp

This adds a fairly simple xhci-platform driver support. Currently it is
used by the dwc3 driver for supporting host mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

Update sg tablesize as we can expand the ring now.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>

When a urb is submitted to xHCI driver, check if queueing the urb will make
the enqueue pointer advance into dequeue seg and expand the ring if it
occurs. This is to guarantee the safety of ring expansion.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>

Allocate 2 segments for transfer ring by default, so we can expand the ring
when the enqueue pointer and dequeue pointer are in different segments.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>

If room_on_ring() check fails, try to expand the ring and check again.

When expand a ring, use a cached ring or allocate new segments, link
the original ring and the new ring or segments, update the original ring's
segment numbers and the last segment pointer.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>

In the past all the rings were allocated with cycle state equal to 1.
Now the driver may expand an existing ring, and the new segments shall be
allocated with the same cycle state as the old one.

This affects ring allocation and cached ring re-initialization.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>

Factor out the segments allocation and free part from ring allocation
and free routines since driver may call them directly when try to expand
a ring.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>

In the past, the room_on_ring() check was implemented by walking all over
the ring, which is wasteful and complicated.

Count the number of free TRBs instead. The free TRBs number should be
updated when enqueue/dequeue pointer is updated, or upon the completion
of a set dequeue pointer command.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>

Store the ring's last segment pointer and number of segments for ring
expansion usage.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>

When allocate a ring, store its type - four transfer types for endpoint,
TYPE_STREAM for stream transfer, and TYPE_COMMAND/TYPE_EVENT for xHCI host.

This helps to get rid of three bool function parameters: link_trbs, isoc
and consumer.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>

__ffs() can tell us which is the SEGMENT_SHIFT value
to be used. This will prevent problems when users are
too fast and don't pay attention to the need of fixing
the Shift after changing TRBS_PER_SEGMENT.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

The latest released errata for USB2.0 ECN LPM adds new fields to USB2.0
extension descriptor, defines two BESL values for device: baseline BESL
and deep BESL. Baseline BESL value communicates a nominal power savings
design point and the deep BESL value communicates a significant power
savings design point.

If device indicates BESL value, driver will use a value count in both
host BESL and device BESL. Use baseline BESL value as default.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Tested-by: Jason Fan <jcfan@qca.qualcomm.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Current code has put_ioctx() called asynchronously from aio_fput_routine();
that's done *after* we have killed the request that used to pin ioctx,
so there's nothing to stop io_destroy() waiting in wait_for_all_aios()
from progressing.  As the result, we can end up with async call of
put_ioctx() being the last one and possibly happening during exit_mmap()
or elf_core_dump(), neither of which expects stray munmap() being done
to them...

We do need to prevent _freeing_ ioctx until aio_fput_routine() is done
with that, but that's all we care about - neither io_destroy() nor
exit_aio() will progress past wait_for_all_aios() until aio_fput_routine()
does really_put_req(), so the ioctx teardown won't be done until then
and we don't care about the contents of ioctx past that point.

Since actual freeing of these suckers is RCU-delayed, we don't need to
bump ioctx refcount when request goes into list for async removal.
All we need is rcu_read_lock held just over the ->ctx_lock-protected
area in aio_fput_routine().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Have ioctx_alloc() return an extra reference, so that caller would drop it
on success and not bother with re-grabbing it on failure exit.  The current
code is obviously broken - io_destroy() from another thread that managed
to guess the address io_setup() would've returned would free ioctx right
under us; gets especially interesting if aio_context_t * we pass to
io_setup() points to PROT_READ mapping, so put_user() fails and we end
up doing io_destroy() on kioctx another thread has just got freed...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull btrfs updates from Chris Mason:
 "I have two additional and btrfs fixes in my for-linus branch.  One is
  a casting error that leads to memory corruption on i386 during scrub,
  and the other fixes a corner case in the backref walking code (also
  triggered by scrub)."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix casting error in scrub reada code
  btrfs: fix locking issues in find_parent_nodes()

Now that module_driver() can handle varargs, use it instead of rolling
our own version.

Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow module_driver take additional parameters which will be passed to the
register and unregister function calls. This allows it to be used in cases
where additional parameters are required (e.g. usb_serial_register_drivers).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Respectfully revert commit e6ca7b89 "memcg: fix mapcount check
in move charge code for anonymous page" for the 3.3 release, so that
it behaves exactly like releases 2.6.35 through 3.2 in this respect.

Horiguchi-san's commit is correct in itself, 1 makes much more sense
than 2 in that check; but it does not go far enough - swapcount
should be considered too - if we really want such a check at all.

We appear to have reached agreement now, and expect that 3.4 will
remove the mapcount check, but had better not make 3.3 different.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Adding the Pantech UML290 and all non-QDL Gobi device IDs from the
qcserial driver now that we have support for shared net/QMI USB
interfaces.  Most of these are not yet tested with this driver, but
should be mostly identical to tested devices, except for device IDs.

Gobi devices provide several different interfaces (serial/net/other)
using the exact same class, subclass and protocol values.  This driver
will only support the net/QMI function while there are other drivers
supporting other device functions. The net/QMI interface number may
also differ from device to device.  It has been noted that all the
other interfaces have additional functional descriptors, so we use that
to detect the interface supported by this driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new cdc-wdm subdriver interface to create a device management
device even for USB devices having a single combined QMI/wwan USB
interface with three endpoints (int, bulk in, bulk out) instead of
separate data and control interfaces.

Some Huawei devices can be switched to a single interface mode for
use with other operating systems than Linux.  This adds support
for these devices when they run in such non-Linux modes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some WWAN LTE/3G devices based on chipsets from Qualcomm provide
near standard CDC ECM interfaces in addition to the usual serial
interfaces.   The Huawei E392/E398 are examples of such devices.

These typically cannot be fully configured using AT commands
over a serial interface.  It is necessary to speak the proprietary
Qualcomm MSM Interface (QMI) protocol to the device to enable the
ethernet proxy functionality.

The devices embed the QMI protocol in CDC on the control interface,
using standard CDC commands and notifications. The do not otherwise
use CDC commands for the ethernet function.  This driver does
therefore not need access to any other aspects of the control
interface than the descriptors attached to it.

Another driver, cdc-wdm, will provide userspace access to the
QMI protocol independently of this driver.  To facilitate this,
this driver avoids binding to the control interface, and uses
only the associated data interface after parsing the common CDC
functional descriptors on the control interface.

You will want both the cdc-wdm and option drivers as companions to
this driver, to have full access to all interfaces and protocols
exported by the device.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit f0fbf0ab ("x86: integrate delay functions") converted
delay_tsc() into a random delay generator for 64 bit.  The reason is
that it merged the mostly identical versions of delay_32.c and
delay_64.c.  Though the subtle difference of the result was:

 static void delay_tsc(unsigned long loops)
 {
-	unsigned bclock, now;
+	unsigned long bclock, now;

Now the function uses rdtscl() which returns the lower 32bit of the
TSC. On 32bit that's not problematic as unsigned long is 32bit. On 64
bit this fails when the lower 32bit are close to wrap around when
bclock is read, because the following check

       if ((now - bclock) >= loops)
       	  	break;

evaluated to true on 64bit for e.g. bclock = 0xffffffff and now = 0
because the unsigned long (now - bclock) of these values results in
0xffffffff00000001 which is definitely larger than the loops
value. That explains Tvortkos observation:

"Because I am seeing udelay(500) (_occasionally_) being short, and
 that by delaying for some duration between 0us (yep) and 491us."

Make those variables explicitely u32 again, so this works for both 32
and 64 bit.
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@onelan.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # >= 2.6.27
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Michał Wróbel <michal.wrobel@flytronic.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull sound fixes from Takashi Iwai:
 "Nothing exciting here: just a few regression fixes for HD-audio and
  ASoC, also the support of missing 32bit compat ioctl for HDSPM."

* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hdspm - Provide ioctl_compat
  ALSA: hda/realtek - Apply the coef-setup only to ALC269VB
  ALSA: hda - add quirk to detect CD input on Gigabyte EP45-DS3
  ASoC: neo1973: fix neo1973 wm8753 initialization

The msm git tree moved to

  git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm.gitSigned-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull C6X fix from Mark Salter:
 "Fix for C6X KSTK_EIP and KSTK_ESP macros."

* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
  C6X: fix KSTK_EIP and KSTK_ESP macros

Pull two IOMMU fixes from Joerg Roedel:
 "The first is an additional fix for the OMAP initialization order issue
  and the second patch fixes a possible section mismatch which can lead
  to a kernel crash in the AMD IOMMU driver when suspend/resume is used
  and the compiler has not inlined the iommu_set_device_table function."

* tag 'iommu-fixes-v3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  x86/amd: iommu_set_device_table() must not be __init
  ARM: OMAP: fix iommu, not mailbox

Pull radeon drm stuff from Dave Airlie:
 "Just some radeon fixes, one is for an oops where we run out of ioremap
  space on some big hardware systems in 32-bit mode, stuff doesn't work
  properly but at least the machine will boot.

  One regression fix, and two bugs, one hw, one blit code."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: fix hdmi duallink checks
  drm/radeon/kms: set SX_MISC in the r6xx blit code (v2)
  drm/radeon: deal with errors from framebuffer init path.
  drm/radeon: fix a semaphore deadlock on pre cayman asics

Pull networking from David Miller:

1) IPV4 routing metrics can become stale when routes are changed by the
   administrator, fix from Steffen Klassert.

2) atl1c does "val |= XXX;" where XXX is a bit number not a bit mask,
   fix by using set_bit.  From Dan Carpenter.

3) Memory accounting bug in carl9170 driver results in wedged TX queue.
   Fix from Nicolas Cavallari.

4) iwlwifi accidently uses "sizeof(ptr)" instead of "sizeof(*ptr)", fix
   from Johannes Berg.

5) Openvswitch doesn't honor dp_ifindex when doing vport lookups, fix
   from Ben Pfaff.

6) ehea conversion to 64-bit stats lost multicast and rx_errors
   accounting, fix from Eric Dumazet.

7) Bridge state transition logging in br_stp_disable_port() is busted,
   it's emitted at the wrong time and the message is in the wrong tense,
   fix from Paulius Zaleckas.

8) mlx4 device erroneously invokes the queue resize firmware operation
   twice, fix from Jack Morgenstein.

9) Fix deadlock in usbnet, need to drop lock when invoking usb_unlink_urb()
   otherwise we recurse into taking it again.  Fix from Sebastian Siewior.

10) hyperv network driver uses the wrong driver name string, fix from
    Haiyang Zhang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net/hyperv: Use the built-in macro KBUILD_MODNAME for this driver
  net/usbnet: avoid recursive locking in usbnet_stop()
  route: Remove redirect_genid
  inetpeer: Invalidate the inetpeer tree along with the routing cache
  mlx4_core: fix bug in modify_cq wrapper for resize flow.
  atl1c: set ATL1C_WORK_EVENT_RESET bit correctly
  bridge: fix state reporting when port is disabled
  bridge: br_log_state() s/entering/entered/
  ehea: restore multicast and rx_errors fields
  openvswitch: Fix checksum update for actions on UDP packets.
  openvswitch: Honor dp_ifindex, when specified, for vport lookup by name.
  iwlwifi: fix wowlan suspend
  mwifiex: reset encryption mode flag before association
  carl9170: fix frame delivery if sta is in powersave mode
  carl9170: Fix memory accounting when sta is in power-save mode.

Pull last minute fixes from Olof Johansson:
 "One samsung build fix due to a mis-applied patch, and a small set of
  OMAP fixes.  This should be the last from arm-soc for 3.3, hopefully."

* tag 'fixes-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: S3C2440: Fixed build error for s3c244x
  ARM: OMAP2+: Fix module build errors with CONFIG_OMAP4_ERRATA_I688
  ARM: OMAP: id: Add missing break statement in omap3xxx_check_revision
  ARM: OMAP2+: Remove apply_uV constraints for fixed regulator
  ARM: OMAP: irqs: Fix NR_IRQS value to handle PRCM interrupts

Pull regulator fix from Mark Brown:
 "Another small, clear fix in a specific driver."

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: tps65910: Configure correct value for VDDCTRL vout reg

Pull minor devicetree bug fixes and documentation updates from Grant Likely:
 "Fixes up a duplicate #include, adds an empty implementation of
  of_find_compatible_node() and make git ignore .dtb files.  And fix up
  bus name on OF described PHYs.  Nothing exciting here."

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  doc: dt: Fix broken reference in gpio-leds documentation
  of/mdio: fix fixed link bus name
  of/fdt.c: asm/setup.h included twice
  of: add picochip vendor prefix
  dt: add empty of_find_compatible_node function
  ARM: devicetree: Add .dtb files to arch/arm/boot/.gitignore

Pull SPI section mismatch bug fix for v3.3-rc3 from Grant Likely:
 "Minor fix for pl022_dma_probe() function which was put in the wrong
  section."

* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  Fix section mismatch in spi-pl022.c

Pull four hwmon patches from Guenter Roeck

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (jc42) Add support for AT30TS00, TS3000GB2, TSE2002GB2, and MCP9804
  hwmon: (zl6100) Maintain delay parameter in driver instance data
  hwmon: (pmbus_core) Fix maximum number of POUT alarm attributes
  hwmon: (jc42) Add support for ST Microelectronics STTS2002 and STTS3000

Pull device-mapper fixes for 3.3 from Alasdair Kergon

Eight small device-mapper bug fixes.

* tag 'dm-3.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm raid: fix flush support
  dm raid: set MD_CHANGE_DEVS when rebuilding
  dm thin metadata: decrement counter after removing mapped block
  dm thin metadata: unlock superblock in init_pmd error path
  dm thin metadata: remove incorrect close_device on creation error paths
  dm flakey: fix crash on read when corrupt_bio_byte not set
  dm io: fix discard support
  dm ioctl: do not leak argv if target message only contains whitespace