- 24 Aug, 2011 20 commits
-
-
Felix Fietkau authored
On embedded hardware it's normal to not have a PCI device for the PCI bridge that the wifi card is attached to. pdev->bus->self will be NULL in that case. In that case, simply return without emitting an useless kernel stack trace. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k/dump_nfcal Signed-off-by:
Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by:
-
Rajkumar Manoharan authored
While switching b/w HT20/40, the current channel's nf values are updated into history buffer. Since the current channel's channel type, channel flag got updated before reading nf value from hw. This channel type mismatch is causing invalid readings when hw is on ht20 but getnf tries to read on extn chains. Signed-off-by:
-
Rajkumar Manoharan authored
Before doing hw reset the current channel's noisefloor readings are updated into history buffer. The extension chain's readings are considered only if the current channel was configured in HT40. While moving from HT40 to HT20, the extn chain's readings are skipped though the current channel is in ht40. This patch updates extn chain reading based on channel flag. Signed-off-by:
-
Rajkumar Manoharan authored
Signed-off-by:
-
Rajkumar Manoharan authored
Signed-off-by:
-
Rajkumar Manoharan authored
The chainmasks were already configured at process_ini before doing init calibration. Signed-off-by:
-
Rajkumar Manoharan authored
Signed-off-by:
-
Rajkumar Manoharan authored
Signed-off-by:
-
Rajkumar Manoharan authored
Once RXEOL was disabled, it never be enabled again. This patch re-enables rxeol at the end of rx tasklet. Signed-off-by:
-
Rajkumar Manoharan authored
Whenever RXEOL is received, both RXORN and RXEOL got cleared to avoid rx overrun interrupt storm. This was handled only for edma chips. The same scenario was also observered with AR9280, doing frequent channel type switch b/w HT20/40 with bidi traffic that is causing failure to stop rx dma. This patch clears the RXEOL & RXORN interrupts for all chips. ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x000062c0 ath: Could not stop RX, we could be confusing the DMA engine when we start RX up ------------[ cut here ]------------ WARNING: at drivers/net/wireless/ath/ath9k/recv.c:532 ath_stoprecv+0x110/0x120 [ath9k]() Call Trace: [<ffffffff8104a55a>] warn_slowpath_common+0x7a/0xb0 [<ffffffff8104a5a5>] warn_slowpath_null+0x15/0x20 [<ffffffffa0560380>] ath_stoprecv+0x110/0x120 [ath9k] [<ffffffffa055e6fa>] ath_reset+0x6a/0x200 [ath9k] Signed-off-by:
-
Rajkumar Manoharan authored
The WAR which adds extra delimiters when using RTS/CTS with aggregation and non-enterprise AR9003 chips. This extra padding is done after doing all the 4ms limit checks and hence the total aggregate sizes are exceeding the allowed duration. This patch limits the aggregate sizes appropriately after including these extra delimiters. Signed-off-by:
-
Javier Cardona authored
Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute, which will advertise this mesh node as being a mesh gate. NL80211_HWMP_ROOTMODE must be set or this will do nothing. Signed-off-by:
Javier Cardona <javier@cozybit.com> Signed-off-by:
-
Javier Cardona authored
Allow userspace to set Root Announcement Interval for our mesh interface. Also, RANN interval is now in proper units of TUs. Signed-off-by:
-
Javier Cardona authored
This fix allows userspace to mark a meshif as a root node. Signed-off-by:
-
Javier Cardona authored
In this implementation, a mesh gate is a root node with a certain bit set in its RANN flags. The mpath to this root node is marked as a path to a gate, and added to our list of known gates for this if_mesh. Once a path discovery process fails, we forward the unresolved frames to a known gate. Thanks to Luis Rodriguez for refactoring and bug fix help. Signed-off-by:
-
Javier Cardona authored
Previously, mpaths were never flushed since the mpath is not active once we call this function. Signed-off-by:
-
Javier Cardona authored
mesh_queue_preq is invoked invoked from both user (work queue) and softirq (timer) context, so the _bh version of spinlock needs to be used. Also, the mpath->state_lock should be softirq safe as well. Signed-off-by:
-
Javier Cardona authored
If we have an mpath whose timer has not been initialized, don't try to delete it. Signed-off-by:
-
Javier Cardona authored
make hwmp_dbg print the relevant sdata->name by default and improve formatting. Also add mpath_dbg macro for debugging of mesh path operations. Signed-off-by:
-
- 23 Aug, 2011 1 commit
-
-
Rafał Miłecki authored
Sometimes we need to write table which is 2-10 elements long. It's easier to create such a function instead of defining array every time. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
- 22 Aug, 2011 19 commits
-
-
Rafał Miłecki authored
Signed-off-by:
-
Stefan Assmann authored
No need to recompile the module anymore to set the debug level. Signed-off-by:
Stefan Assmann <sassmann@kpanic.de> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
MMIO hacks were used to trick ndis&wl. For example following: phy_read(0x0280) -> 0xffff phy_write(0x0280) <- 0xff3e *** phy_read(0x0280) -> 0x0000 phy_write(0x0280) <- 0x003e was translated to mask 0xff00 and set 0x3e. Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Nishant Sarmukadam authored
When a client disassociates from a crypto enabled bss, data traffic to other clients connected to the bss is stalled. This was due to a boolean variable used to keep track if HW crypto is enabled i.e. if set key has been called to add a key. This flag was being reset every time delete key was called e.g when a station leaves the bss. Once the flag is reset, rx status flags were not being set for connected clients which disrupts traffic to these clients. Fix this issue by not resetting the flag since we do not need to reset this flag during the life time of the bss. Signed-off-by:
Nishant Sarmukadam <nishants@marvell.com> Signed-off-by:
-
Thomas Pedersen authored
Make mesh path selection frames Mesh Action category, remove outdated Mesh Path Selection category and defines, use updated reason codes, add mesh_action_is_path_sel for readability, and update/correct path selection IEs. Signed-off-by:
Thomas Pedersen <thomas@cozybit.com> Signed-off-by:
-
Thomas Pedersen authored
Signed-off-by:
-
Thomas Pedersen authored
This patch updates the mesh peering frames to the format specified in the recently ratified 802.11s standard. Several changes took place to make this happen: - Change RX path to handle new self-protected frames - Add new Peering management IE - Remove old Peer Link IE - Remove old plink_action field in ieee80211_mgmt header These changes by themselves would either break peering, or work by coincidence, so squash them all into this patch. Signed-off-by:
-
Thomas Pedersen authored
Have the mesh peering frames use the self-protected action and reason codes specified in 802.11s and defined in ieee80211.h. Remove the local enums. Signed-off-by:
-
Thomas Pedersen authored
802.11s introduces a new action frame category, add action codes as well as an entry in ieee80211_mgmt. Signed-off-by:
-
Thomas Pedersen authored
Correct ordering of IEs in the mesh beacon while removing unneeded IEs from mesh peering frames. Set privacy bit in capability info if security is enabled. Add utility functions to aid in construction of IEs and reduce code duplication. Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
We need to disable ext. PA lines for reading SPROM. It's disabled by default, but this patch allows using bcma after loading wl, which leaves workaround enabled. Cc: Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
