This message is encountered regularly and we need to take a closer look at
the circumstances under which it is printed before presenting errors to
users.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

If RTS/CTS protection is needed for HT, wait until get operational
notification from mac80211, then inform uCode to switch to RTS/CTS
through RXON command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

When resuming from hibernate or suspend,
the status of the rfkill switch isn't
known since it might have been toggled
while the system was asleep. Therefore,
we need to read out the status at resume
time to make sure the system knows about
an up-to-date status.
Reported-by: Mark Tung <mark.y.tung@intel.com>
Tested-by: Mark Tung <mark.y.tung@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

The rate table in the bcast LQ is computed only when the station is
allocated, and chooses the lowest rate for the band. Because of when this
occurs, this is the 2.4 GHz band and uses the 0x420a (CCK, 1 Mbps) rate. In 5 GHz
beaconing mode, this rate will prevent beacons from being sent and any other
packets from being received.

We can fix this by re-initializing the bcast station's LQ command when the
channel is changed.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

For some devices, especially the upcoming new devices, the plcp error
rate is different. Before the correct error rate can be determine, also
for the debugging purpose; add the mechanism to disable plcp error checking
which cause radio reset happen.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Different devices have different calibration requirement,
some need DC calibration and some don't; make it a cfg parameter
for easy management.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

This bit need to be set for both RTS/CTS or CTS-to-self protection, if
CTS-to-self is used, then uCode will  check the RXON_FLG_SELF_CTS_EN
status. Change the name from TX_CMD_FLG_RTS_CTS_MSK to TX_CMD_FLAG_PROT_REQUIRE_MSK
to match the behavior of the bit setting.

Also update comments to reflect which hardware uses which of the TX command
flags.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

When building tx command, always set TX_CMD_FLAG_PROT_REQUIRE_MSK
for 5000 series and up.

Without setting this bit the firmware will not examine the RTS/CTS setting
and thus not send traffic with the appropriate protection. RTS/CTS is is
required for HT traffic in a noisy environment where, without this setting,
connections will stall on some hardware as documented in the patch that
initially attempted to address this:

    commit 1152dcc2
    Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
    Date:   Fri Jan 15 13:42:58 2010 -0800

    iwlwifi: Fix throughput stall issue in HT mode for 5000

    Similar to 6000 and 1000 series, RTS/CTS is the recommended
    protection mechanism for 5000 series in HT mode based on the HW design.
    Using RTS/CTS will better protect the inner exchange from interference,
    especially in highly-congested environment, it also prevent uCode encounter
    TX FIFO underrun and other HT mode related performance issues.

For 3945 and 4965, different flags are used for RTS/CTS or CTS-to-Self
protection.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

commit 3474ad63
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Thu Apr 29 04:43:05 2010 -0700

    iwlwifi: apply filter flags directly

broke multicast. The reason, it turns out, is that
the code previously checked if ALLMULTI _changed_,
which the new code no longer did, and normally it
_never_ changes. Had somebody changed it manually,
the code prior to my patch there would have been
broken already.

The reason is that we always, unconditionally, ask
the device to pass up all multicast frames, but the
new code made it depend on ALLMULTI which broke it
since now we'd pass up multicast frames depending
on the default filter in the device, which isn't
necessarily what we want (since we don't program it
right now).

Fix this by simply not checking allmulti as we have
allmulti behaviour enabled already anyway.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Move ath9k_ps_wakeup() down just before accessing hw registers.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is possbile that the transmission of paprd test frame
might not get completed in 100ms if tx is stuck. Freeing
this skb upon timeout in ath_paprd_calibrate() will result
in accessing already freed memory when the associated pending
buffer is drained in txq. This patch fixes this issue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

HW crypto in rt2500usb does not seem to support keys with different ciphers,
which breaks TKIP+AES mode. Fall back to software encryption to fix it.

This should fix long-standing problems with rt2500usb and WPA, such as:
http://rt2x00.serialmonkey.com/phpBB/viewtopic.php?f=4&t=4834
https://bugzilla.redhat.com/show_bug.cgi?id=484888

Also tested that it does not break WEP, TKIP-only and AES-only modes.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds transmit power setting type and transmit power level attributes
to NL80211_CMD_SET_WIPHY in order to facilitate adjusting of the transmit power
level of the device.

The added attributes allow selection of automatic, limited or fixed transmit
power level, with the level definable in signed mBm format.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In preparation for a TX power setting interface in the nl80211, change the
.set_tx_power function to use mBm units instead of dBm for greater accuracy and
smaller power levels.

Also, already in advance move the tx_power_setting enumeration to nl80211.

This change affects the .tx_set_power function prototype. As a result, the
corresponding changes are needed to modules using it. These are mac80211,
iwmc3200wifi and rndis_wlan.

Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver at76c50x-usb is unable to authenticate with an AP since
kernel 2.6.31 for the following reason: The join command of the firmware
needs to be sent with the right bssid before any transmission can start.
Before kernel 2.6.31 mac80211 informed its drivers about the changing
bssid early enough for at76c50x-usb but during the development of 2.6.31
mac80211's behaviour changed. Now a new bssid is set after the
association.

This patch changes the tx routine of the driver at76c50x-usb in such a
way that a new bssid is extracted from an authentication frame and the
join command with that bssid is processed.
Signed-off-by: Sebastian Smolorz <sesmo@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch does a simple code move of at76_join() so that
at76_mac80211_tx() follows at76_join() in the driver's source file.

This is a preparatory patch for the following patch where we need
to call at76_join() from at76_mac80211_tx() in order to
authenticate successfully with a bssid.
Signed-off-by: Sebastian Smolorz <sesmo@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While mesh_rx_plink_frame holds sta->lock...

mesh_rx_plink_frame ->
	mesh_plink_inc_estab_count ->
		ieee80211_bss_info_change_notify

...but ieee80211_bss_info_change_notify is allowed to sleep.  A driver
taking advantage of that allowance can cause a scheduling while
atomic bug.  Similar paths exist for mesh_plink_dec_estab_count,
so work around those as well.

http://bugzilla.kernel.org/show_bug.cgi?id=16099

Also, correct a minor kerneldoc comment error (mismatched function names).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/mac80211/rc80211_minstrel_ht.c:440:46: warning: incorrect type in argument 2 (different signedness)
net/mac80211/rc80211_minstrel_ht.c:440:46:    expected int *idx
net/mac80211/rc80211_minstrel_ht.c:440:46:    got unsigned int *<noident>
net/mac80211/rc80211_minstrel_ht.c:446:46: warning: incorrect type in argument 2 (different signedness)
net/mac80211/rc80211_minstrel_ht.c:446:46:    expected int *idx
net/mac80211/rc80211_minstrel_ht.c:446:46:    got unsigned int *<noident>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>

net/mac80211/rx.c:2059:39: warning: symbol 'mgmt' shadows an earlier one
net/mac80211/rx.c:1916:31: originally declared here
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

There are few places where ANI is started without checking
if it is right to start. This might lead to a case where ani
timer would be left undeleted and cause improper memory acccess
during module unload. This bug is clearly exposed with
paprd support where the driver detects tx hang and does a
chip reset. During this reset ani is (re)started without checking
if it needs to be started. This would leave a timer scheduled
even after all the resources are freed and cause a panic.

This patch introduces a bit in sc_flags to indicate if ani
needs to be started in sw_scan_start() and ath_reset().
This would fix the following panic. This issue is easily seen
with ar9003 + paprd.

 BUG: unable to handle kernel paging request at 0000000000003f38
[<ffffffff81075391>] ? __queue_work+0x41/0x50
[<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370
[<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110
[<ffffffff81061f69>] __do_softirq+0xb9/0x1f0
[<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160
[<ffffffff8100af5c>] call_softirq+0x1c/0x30
[<ffffffff8100c9f5>] do_softirq+0x65/0xa0
[<ffffffff81061e25>] irq_exit+0x85/0x90
[<ffffffff8155e095>] do_IRQ+0x75/0xf0
[<ffffffff815570d3>] ret_from_intr+0x0/0x11
<EOI>
[<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119
[<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119
[<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140
[<ffffffff81008da3>] cpu_idle+0xb3/0x110
[<ffffffff81550722>] start_secondary+0x1ee/0x1f5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Probably little risk of namespace polution, but good practice... :-)
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some vendors require the LED to be ON always irrespective of any
radio activity. Introducing a module parameter to disable blinking,
so that one can choose between always on or led blink during
activity.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Without this we could start trying to work with the device without
it being fully functional yet and loose some packets upon resume.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The array we use will vary depending on whether or not we are
to go to lower power or not. The default values (iniPcieSerdes)
are a copy or what go into the registers through the INI files.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This can be useful during testing of new ASPM tweaks which often
have to be done through the PCI Serializer-Deserializer (SERDES).

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The LowPower array writes disables the PLL when ASPM is enabled.
The host driver makes quite a few calls to ath9k_hw_configpcipowersave()
and these same calls also need to ensure the PLL is off when they issue
it.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The AR_WA register should not be read when in sleep state so
add a variable we can stash its value into for when we need
to set it. Additionally the AR_WA_D3_TO_L1_DISABLE_REAL
(bit 16) needs to be removed.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Added 11d support for libertas driver using cfg80211. This is based on Holger
Shurig's initial work to add cfg80211 support libertas.
(https://patchwork.kernel.org/patch/64286/)

Please let us know, if there are any improvements comments.

Code is added to send 11d enable command to firmware while
initialisation and pass 11d specific information to firmware
when notifier handler is called by cfg80211.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In following scenarios WARN_ON() in cfg80211 code was triggered.
a) Driver unload or card removal.
b) Disconnect from infra network
c) Adhoc start/join
d) Adhoc stop
Added following fixes to avoid WARN_ON() in cfg80211 code.
a) Ensured that cfg80211_disconnected() function defined in cfg80211
code will be called only in infra mode.
b) Solved timing issue by moving cfg80211_disconnected() call inside
lbs_cfg_disconnect().
c) Updated "wdev->ssid" in driver code after Adhoc join/start
d) Removed unnecessory cfg80211_disconnected() call in lbs_remove_card.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Holger Schurig's patch (https://patchwork.kernel.org/patch/64286/)
is rebased to latest wireless-testing tree.

(Includes patches from me originally posted as "libertas: fix build
error due to undefined symbol" and "libertas: unmangle capability
value". -- JWL)
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This mechanism introduced in this patch applies (at least) for hardware
designs using a single shared antenna for both WLAN and BT. In these designs,
the antenna must be toggled between WLAN and BT.

In those hardware, managing WLAN co-existence with Bluetooth requires WLAN
full power save whenever there is Bluetooth activity in order for WLAN to be
able to periodically relinquish the antenna to be used for BT. This is because
BT can only access the shared antenna when WLAN is idle or asleep.

Some hardware, for instance the wl1271, are able to indicate to the host
whenever there is BT traffic. In essence, the hardware will send an indication
to the host whenever there is, for example, SCO traffic or A2DP traffic, and
will send another indication when the traffic is over.

The hardware gets information of Bluetooth traffic via hardware co-existence
control lines - these lines are used to negotiate the shared antenna
ownership. The hardware will give the antenna to BT whenever WLAN is sleeping.

This patch adds the interface to mac80211 to facilitate temporarily disabling
of dynamic power save as per request of the WLAN driver. This interface will
immediately force WLAN to full powersave, hence allowing BT coexistence as
described above.

In these kind of shared antenna desings, when WLAN powersave is fully disabled,
Bluetooth will not work simultaneously with WLAN at all. This patch does not
address that problem. This interface will not change PSM state, so if PSM is
disabled it will remain so. Solving this problem requires knowledge about BT
state, and is best done in user-space.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix the following compile warning:

CC [M]  net/mac80211/scan.o
net/mac80211/scan.c: In function 'ieee80211_request_internal_scan':
net/mac80211/scan.c:749:23: warning: comparison between 'enum nl80211_band' and 'enum ieee80211_band'

caused by the local variable band not being of the proper 'ieee80211_band' type.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The message following fatal DMA errors fails to indicate properly that the
driver has switched to PIO mode.
Signed-off-by: Larry Finger <Larry.Finger@wfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove the reference to non-exist function in iwlcore
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>