Giuseppe Cavallaro says:

====================
stmmac EEE fixes

This is a subset of patches to provide some fixes for the EEE support inside the
driver.
Patches have been tested on boards EEE capable plugged on switch w/ w/o EEE
support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of PLS is active the PLS (PHY Link Status) bit in
the Reg12 has to be set to allow the MAC to asserts the LPI
pattern when the link is ok.
Signed-off-by: nandini sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to skip the EEE initialisation when the stmmac
is using a switch (with a fixed phy support).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The value for LPI TW timer has to be updated to 0x1E that is the hardcoded value
of 20.5us and it will apply to all EEE enabled Remote PHYs.
Disadvantage is for PHY's that support lesser wakeup time but we can accept it
waiting to implement LLDP to negotiate the Wakeup time of Remote PHY.
Signed-off-by: nandini sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to fix the definition of macros for EEE otherwise the LPI TX/RX
entry/exit cannot be properly managed.
Signed-off-by: Nandini Sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since SCTP day 1, that is, 19b55a2af145 ("Initial commit") from lksctp
tree, the official <netinet/sctp.h> header carries a copy of enum
sctp_sstat_state that looks like (compared to the current in-kernel
enumeration):

  User definition:                     Kernel definition:

  enum sctp_sstat_state {              typedef enum {
    SCTP_EMPTY             = 0,          <removed>
    SCTP_CLOSED            = 1,          SCTP_STATE_CLOSED            = 0,
    SCTP_COOKIE_WAIT       = 2,          SCTP_STATE_COOKIE_WAIT       = 1,
    SCTP_COOKIE_ECHOED     = 3,          SCTP_STATE_COOKIE_ECHOED     = 2,
    SCTP_ESTABLISHED       = 4,          SCTP_STATE_ESTABLISHED       = 3,
    SCTP_SHUTDOWN_PENDING  = 5,          SCTP_STATE_SHUTDOWN_PENDING  = 4,
    SCTP_SHUTDOWN_SENT     = 6,          SCTP_STATE_SHUTDOWN_SENT     = 5,
    SCTP_SHUTDOWN_RECEIVED = 7,          SCTP_STATE_SHUTDOWN_RECEIVED = 6,
    SCTP_SHUTDOWN_ACK_SENT = 8,          SCTP_STATE_SHUTDOWN_ACK_SENT = 7,
  };                                   } sctp_state_t;

This header was later on also placed into the uapi, so that user space
programs can compile without having <netinet/sctp.h>, but the shipped
with <linux/sctp.h> instead.

While RFC6458 under 8.2.1.Association Status (SCTP_STATUS) says that
sstat_state can range from SCTP_CLOSED to SCTP_SHUTDOWN_ACK_SENT, we
nevertheless have a what it appears to be dummy SCTP_EMPTY state from
the very early days.

While it seems to do just nothing, commit 0b8f9e25 ("sctp: remove
completely unsed EMPTY state") did the right thing and removed this dead
code. That however, causes an off-by-one when the user asks the SCTP
stack via SCTP_STATUS API and checks for the current socket state thus
yielding possibly undefined behaviour in applications as they expect
the kernel to tell the right thing.

The enumeration had to be changed however as based on the current socket
state, we access a function pointer lookup-table through this. Therefore,
I think the best way to deal with this is just to add a helper function
sctp_assoc_to_state() to encapsulate the off-by-one quirk.
Reported-by: Tristan Su <sooqing@gmail.com>
Fixes: 0b8f9e25 ("sctp: remove completely unsed EMPTY state")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit ed98df33 ("net: use __GFP_NORETRY for high order
allocations") we tried to address one issue caused by order-3
allocations.

We still observe high latencies and system overhead in situations where
compaction is not successful.

Instead of trying order-3, order-2, and order-1, do a single order-3
best effort and immediately fallback to plain order-0.

This mimics slub strategy to fallback to slab min order if the high
order allocation used for performance failed.

Order-3 allocations give a performance boost only if they can be done
without recurring and expensive memory scan.

Quoting David :

The page allocator relies on synchronous (sync light) memory compaction
after direct reclaim for allocations that don't retry and deferred
compaction doesn't work with this strategy because the allocation order
is always decreasing from the previous failed attempt.

This means sync light compaction will always be encountered if memory
cannot be defragmented or reclaimed several times during the
skb_page_frag_refill() iteration.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
Setup mlx4 user space Ethernet QPs to properly handle VXLAN

This short series fixes the mlx4 driver setting of user space Ethernet QPs
(e.g those opened by DPDK applications) such that they will properly handle
VXLAN traffic/offloads
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Raw Ethernet QPs opened from user-space lack the proper setup to
recieve/handle VXLAN traffic when VXLAN offloads are enabled.

Fix that by adding a tunnel steering rule on top of the normal unicast
steering rule and set the tunnel_type field in the QP context.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the function which we use to set VXLAN DMFS (flow-steering) rules
from mlx4_en to mlx4_core. This refactoring will allow the mlx4_ib driver
to call the helper for the use case of user-space RAW Ethernet QPs, such
that they can serve VXLAN traffic too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enabling DMA_API_DEBUG, warnings are reported at runtime
because the device driver frees DMA memory with wrong functions
and it does not call dma_mapping_error after mapping dma memory.

The first problem is fixed by of introducing a flag that helps us
keeping track which mapping technique was used, so that we can use
the right API for unmap.
This approach was inspired by the e1000 driver, which uses a similar
technique.
Signed-off-by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Denis Kirjanov <kda@linux-powerpc.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PTP reference clock, used for setting the addend in the Timestamp Addend
Register, was erroneously hard-coded (as reported in the databook just as
example).

The patch removes the macro named: STMMAC_SYSCLOCK and allows to use a
reference clock (clk_ptp_ref_i) that can be passed from the platform.

If not passed, the main driver clock will be used as default; note that
this can be fine on some platforms.

Note that, prior this patch, using the old STMMAC_SYSCLOCK on some platforms,
as side effect, the ptp clock can move faster/slower than the system clock.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to fix a typo on mmc rx crc error when reported by ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to w/a a problem that happens on some boxes when run at 10Mbps
Half duplex mode.

During the transmission the CSR signal is asserted for some time and the frames
aborted because of carrier sense error.
This is reported by MMC HW counter: txcarrier signal.
This actually is a false carrier so the frames are good and there is no reason
to ask for dropping them.

This patch so disables the Carrier Sense During Transmission
and this means that the MAC transmitter ignore the CRS signal
during frame transmission in Half-Duplex mode.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the Std 802.3az if the EEE Adv (Reg 7.60), Link partner ability
(Reg 7.61) and EEE capability (Register 3.20) bits return 0 this  means no EEE
is supported. So this patch fixes the checks inside the phy_init_eee function.
Signed-off-by: Nandini Sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/marvell/mvneta.c: In function 'mvneta_skb_tx_csum':
drivers/net/ethernet/marvell/mvneta.c:1374:3: error: implicit declaration of function 'vlan_get_protocol' [-Werror=implicit-function-declaration]
   __be16 l3_proto = vlan_get_protocol(skb);
   ^
Reporeted-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Interrupt is enabled when bind_interdomain_evtchn_to_irqhandler returns.
If there's interrupt pending interrupt handler is invoked.

NAPI needs to be initialised before binding interrupt otherwise the
interrupt handler will try to scheduling a NAPI instance that is not
initialised yet, resulting in kernel OOPS.

This fixes a regression introduced in ea2c5e13 ("xen-netback: move NAPI
add/remove calls").

Ideally function calls to create kthreads should also be moved before
binding but I intent to fix this regression with minimal changes and
refactor the code with another patch.
Reported-by: Thomas Leonard <talex5@gmail.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladislav Yasevich says:

====================
Fix TSO and checksum issues with non-accelerated vlan traffic.

I've recently ran across something rather interesting when testing vlans
from inside VMs.  In some scenarios I was getting awfull thruput.
Some debugging uncovered a very scary packet corruption.  I was
seeing packets that had original TSO length as IP total length
and their ip checksum was 0.  This was with e1000e driver.

A bit more debugging uncovered an assumption made by that driver
that skb->protocol will contain l3 protocol information.  This
was not the case in my setup since I manually turned off vlan
tx acceleration for the device.  This caused the driver to not
initialize the tso information correctly and resulted in
corrupt TSO frames on the wire.

I decided to do some auditing of the usage of skb->protocols
in the drivers.  Out of all the drivers, the included 8 appear
to be effected.  They all allow user to control vlan acceleration
settings, all support TSO on vlan devices, and all use
skb->protocol to decide how to encode TSO information.  Some
also have similar problems when initializing hw checksum information.
On such device, it is simple enough to reproduce the issue.
Simply turn off TX VLAN acceleration on the device, create a vlan,
and run you favorite network performance tool.

There is 1 driver I ran across that I belive will trigger a BUG
in the system when used with vlans.  That driver is tile/tilepro.c
I have not changed it in this patch set and would hope that
the maintainer has time to look at it.

V2: Fix i40ev using the wrong function name.  Full build.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This device claims TSO support for vlans.  It also allows a user to
control vlan acceleration offloading.  As such, it is possible to turn
off vlan acceleration and configure a vlan which will continue to send
TSO traffic.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information.
This results in corrupted frames sent on the wire.

This patch extracts the protocol value correctly by using a
vlan_get_protocol() helper and corrects corrupt TSO frames.

CC: Shahed Shaikh <shahed.shaikh@qlogic.com>
CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
CC: Ron Mercer <ron.mercer@qlogic.com>
CC: linux-driver@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver doesn't appear to support vlan acceleration at
all.  However, it does claim to support TSO and IP checksums
for vlan devices.  Thus any configured vlan device would
end up passing down partial checksums or TSO frames.

The driver also uses the value from skb->protocol to
determine TSO and checksum offload information, but assumes
that skb->protocol holds the l3 protocol information.
As a result, vlan traffic with partial checksums or TSO
will fail those checks and TSO will not happen.

Fix this by using vlan_get_protocol() helper.

CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This device claims TSO and checksum support for vlans.  It also
allows a user to control vlan acceleration offloading.  As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.

This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.

Fix this by using vlan_get_protocol() helper.

CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This device claims TSO and checksum support for vlans.  It also
allows a user to control vlan acceleration offloading.  As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.

This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.

Fix this by using vlan_get_protocol() helper.

CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver claims that it can do TSO and IP checksums on vlan
devices and also allows user to control vlan acceleration offloading.
This makes it possible to push traffic to this driver that has TSO or
partial checksums set, but also have a non-accelearted vlan
header.  In this case, the driver will fail to correctly
identify such traffic and will not correctly perform
segmentation and checksum calculation.

Fix this by using vlan_get_protocol() helper instead of
assuming skb->protocol always has this information.

CC: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This device claims TSO and checksum support for vlans.  It also
allows a user to control vlan acceleration offloading.  As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information.  This results
in corrupted frames sent on the wire.

This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.

CC: Rasesh Mody <rmody@brocade.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This device claims TSO and checksum support for vlans.  It also
allows a user to control vlan acceleration offloading.  As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This will results in corrupted frames sent on the wire.

This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.

CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This device claims  TSO support for vlans.  It also allows a
user to control vlan acceleration offloading.  As such, it is
possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information.  This results
in corrupted frames sent on the wire.  Corruptions include
incorrect IP total length and invalid IP checksum.

This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.

CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If netdev_alloc_skb_ip_align() fails, subsequent code will
try to dereference an invalid pointer.

Continue to next descriptor on error.

While we're at it,

1. eliminate the chance of an endless loop, replace the main
   loop with while(rx < budget)

2. use napi_complete() and remove the explicit napi_gro_flush()
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DMA memory should be synchronized before data is passed
to/from controller.

Add dma_sync_single_for_cpu(.., DMA_FROM_DEVICE) to RX path
and dma_sync_single_for_device(.., DMA_TO_DEVICE) to TX path.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

build_skb() is used to make skbs out of existing RX ring memory
which is bad because the RX ring is allocated only once, on probe.
Memory corruption occur because said memory is reclaimed, i.e.
__kfree_skb() (and eventually put_page()).

Replace build_skb() with netdev_alloc_skb_ip_align() and use memcpy().

Remove SKB_DATA_ALIGN() from RX buffer size while we're at it.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=69041Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TX buffer length is not cleared on ndo_start_xmit().
Failing to do so can bug/hang the controller and
cause TX interrupts to stop altogether.

Remove the readl() and compute a new value for DESC1.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=69031Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is follow-up to

  da08143b ("vlan: more careful checksum features handling")

which introduced more careful feature intersection in vlan code,
taking into account that HW_CSUM should be considered superset
of IP_CSUM/IPV6_CSUM. The same is needed in netif_skb_features()
in order to avoid offloading mismatch warning when vlan is
created on top of a bond consisting of slaves supporting IP/IPv6
checksumming but not vlan Tx offloading.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to properly put to NULL the ptp_clock while un-register the PTP support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to fix the IPC bit into the GMAC control register
that must be done after the core initialization otherwise it will
not have any effect.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Code manipulating sysfs symlinks on adjacent net_devices(s)
currently doesn't take into account that devices potentially
belong to different namespaces.

This patch trying to fix an issue as follows:
- check for net_ns before creating / deleting symlink.
  for now only netdev_adjacent_rename_links and
  __netdev_adjacent_dev_remove are affected, afaics
  __netdev_adjacent_dev_insert implies both net_devs
  belong to the same namespace.
- Drop all existing symlinks to / from all adj_devs before
  switching namespace and recreate them just after.
Signed-off-by: Alexander Y. Fomichev <git.user@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The first initializer in the following

        union vxlan_addr ipa = {
            .sin.sin_addr.s_addr = tip,
            .sa.sa_family = AF_INET,
        };

is optimised away by the compiler, due to the second initializer,
therefore initialising .sin.sin_addr.s_addr always to 0.
This results in netlink messages indicating a L3 miss never contain the
missed IP address. This was observed with GCC 4.8 and 4.9. I do not know about previous versions.
The problem affects user space programs relying on an IP address being
sent as part of a netlink message indicating a L3 miss.

Changing
            .sa.sa_family = AF_INET,
to
            .sin.sin_family = AF_INET,
fixes the problem.
Signed-off-by: Gerhard Stenzel <gerhard.stenzel@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm fix from Thierry Reding:
 "Just one bugfix for the PWM lookup table code that would cause a PWM
  channel to be set to the wrong period and polarity for non-perfect
  matches"

* tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: Fix period and polarity in pwm_get() for non-perfect matches

The new_ctx pointer is set only for non-chanctx drivers.  This yielded a
crash for chanctx-based drivers during channel switch finalization:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
  IP: ieee80211_vif_use_reserved_switch+0x71c/0xb00 [mac80211]

Use an adequate chanctx pointer to fix this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:
 "Here are some bug fixes that have piled up during ksummit/linuxcon.

   1) Fix endian problems in ibmveth, from Anton Blanchard.

   2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
      Benjamin Block.

   3) SCTP association fixes from Daniel Borkmann.

   4) When multiple VLAN headers are present we have to make sure the
      second and subsequent ones are pullable in the SKB otherwise we
      blindly dereference garbage.  From Jiri Benc.

   5) The argument adjustment of the signature of hlist_add_after*()
      introduced a regression in the batman-adv code, fix from Sven
      Eckelmann.

   6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
      Jain.

   7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.

   8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
      Chas Williams.

   9) Truncate packets larger then the TPACKET_V3 format configured
      buffers, otherwise we overwrite past the end of said buffers.
      From Eric Dumazet.

  10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
      Borundia and Shahed Shaikh.

  11) CXGB4 sometimes doesn't get all of the TX completion events it
      should resulting in SKBs getting stuck in the TX queue, from
      Hariprasad Shenai.

  12) When the FEC chip's PTP clock is disabled, you can't access the
      register.  Add necessary checks to avoid the resulting hang, from
      Fugang Duan"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
  drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
  net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
  net: sctp: spare unnecessary comparison in sctp_trans_elect_best
  net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
  ibmveth: Fix endian issues with rx_no_buffer statistic
  net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
  openvswitch: fix panic with multiple vlan headers
  net: ipv6: fib: don't sleep inside atomic lock
  net: fec: ptp: avoid register access when ipg clock is disabled
  cxgb4: Free completed tx skbs promptly
  cxgb4: Fix race condition in cleanup
  sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
  bnx2x: Revert UNDI flushing mechanism
  qlcnic: Fix endianess issue in firmware load from file operation
  qlcnic: Fix endianess issue in FW dump template header
  qlcnic: Fix flash access interface to application
  MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
  macvlan: Allow setting multicast filter on all macvlan types
  packet: handle too big packets for PACKET_V3
  MAINTAINERS: add entry for ec_bhf driver
  ...

Test for definedness of the macro which is actually defined (the
change is hard to see: it is s/SSS/SSA/).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

In SCTP, selection of active (T.ACT) and retransmission (T.RET)
transports is being done whenever transport control operations
(UP, DOWN, PF, ...) are engaged through sctp_assoc_control_transport().

Commits 4c47af4d ("net: sctp: rework multihoming retransmission
path selection to rfc4960") and a7288c4d ("net: sctp: improve
sctp_select_active_and_retran_path selection") have both improved
it towards a more fine-grained and optimal path selection.

Currently, the selection algorithm for T.ACT and T.RET is as follows:

1) Elect the two most recently used ACTIVE transports T1, T2 for
   T.ACT, T.RET, where T.ACT<-T1 and T1 is most recently used
2) In case primary path T.PRI not in {T1, T2} but ACTIVE, set
   T.ACT<-T.PRI and T.RET<-T1
3) If only T1 is ACTIVE from the set, set T.ACT<-T1 and T.RET<-T1
4) If none is ACTIVE, set T.ACT<-best(T.PRI, T.RET, T3) where
   T3 is the most recently used (if avail) in PF, set T.RET<-T.PRI

Prior to above commits, 4) was simply a camp on T.ACT<-T.PRI and
T.RET<-T.PRI, ignoring possible paths in PF. Camping on T.PRI is
still slightly suboptimal as it can lead to the following scenario:

Setup:
        <A>                                <B>
    T1: p1p1 (10.0.10.10) <==>  .'`)  <==> p1p1 (10.0.10.12)  <= T.PRI
    T2: p1p2 (10.0.10.20) <==> (_ . ) <==> p1p2 (10.0.10.22)

    net.sctp.rto_min = 1000
    net.sctp.path_max_retrans = 2
    net.sctp.pf_retrans = 0
    net.sctp.hb_interval = 1000

T.PRI is permanently down, T2 is put briefly into PF state (e.g. due to
link flapping). Here, the first time transmission is sent over PF path
T2 as it's the only non-INACTIVE path, but the retransmitted data-chunks
are sent over the INACTIVE path T1 (T.PRI), which is not good.

After the patch, it's choosing better transports in both cases by
modifying step 4):

4) If none is ACTIVE, set T.ACT_new<-best(T.ACT_old, T3) where T3 is
   the most recently used (if avail) in PF, set T.RET<-T.ACT_new

This will still select a best possible path in PF if available (which
can also include T.PRI/T.RET), and set both T.ACT/T.RET to it.

In case sctp_assoc_control_transport() *just* put T.ACT_old into INACTIVE
as it transitioned from ACTIVE->PF->INACTIVE and stays in INACTIVE just
for a very short while before going back ACTIVE, it will guarantee that
this path will be reselected for T.ACT/T.RET since T3 (PF) is not
available.

Previously, this was not possible, as we would only select between T.PRI
and T.RET, and a possible T3 would be NULL due to the fact that we have
just transitioned T3 in sctp_assoc_control_transport() from PF->INACTIVE
and would select a suboptimal path when T.PRI/T.RET have worse properties.

In the case that T.ACT_old permanently went to INACTIVE during this
transition and there's no PF path available, plus T.PRI and T.RET are
INACTIVE as well, we would now camp on T.ACT_old, but if everything is
being INACTIVE there's really not much we can do except hoping for a
successful HB to bring one of the transports back up again and, thus
cause a new selection through sctp_assoc_control_transport().

Now both tests work fine:

Case 1:

 1. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

 2. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(PF)

 3. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(INACTIVE)

 5. T1 S(PF) T.ACT, T.RET
    T2 S(INACTIVE)

[ 5.1 T1 S(INACTIVE) T.ACT, T.RET
      T2 S(INACTIVE) ]

 6. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(INACTIVE)

 7. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

Case 2:

 1. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

 2. T1 S(PF)
    T2 S(ACTIVE) T.ACT, T.RET

 3. T1 S(INACTIVE)
    T2 S(ACTIVE) T.ACT, T.RET

 5. T1 S(INACTIVE)
    T2 S(PF) T.ACT, T.RET

[ 5.1 T1 S(INACTIVE)
      T2 S(INACTIVE) T.ACT, T.RET ]

 6. T1 S(INACTIVE)
    T2 S(ACTIVE) T.ACT, T.RET

 7. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>