An error was reported upgrading to 4.9.8:
    root@Typhoon:~# ip route add default table 210 nexthop dev eth0 via 10.68.64.1
    weight 1 nexthop dev eth0 via 10.68.64.2 weight 1
    RTNETLINK answers: Operation not supported

The problem occurs when CONFIG_LWTUNNEL is not enabled and a multipath
route is submitted.

The point of lwtunnel_valid_encap_type_attr is catch modules that
need to be loaded before any references are taken with rntl held. With
CONFIG_LWTUNNEL disabled, there will be no modules to load so the
lwtunnel_valid_encap_type_attr stub should just return 0.

Fixes: 9ed59592 ("lwtunnel: fix autoload of lwt modules")
Reported-by: pupilla@libero.it
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under some circumstances it is possible that no new temporary addresses
will be generated.

For instance, addrconf_prefix_rcv_add_addr() indirectly calls
ipv6_create_tempaddr(), which creates a tentative temporary address and
starts dad. Next, addrconf_prefix_rcv_add_addr() indirectly calls
addrconf_verify_rtnl(). Now, assume that the previously created temporary
address has the least preferred lifetime among all existing addresses and
is still tentative (that is, dad is still running). Hence, the next run of
addrconf_verify_rtnl() is performed when the preferred lifetime of the
temporary address ends. If dad succeeds before the next run, the temporary
address becomes deprecated during the next run, but no new temporary
address is generated.

In order to fix this, schedule the next addrconf_verify_rtnl() run slightly
before the temporary address becomes deprecated, if dad succeeded.
Signed-off-by: Marcus Huewe <suse-tux@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Load correct firmware in rtl8192ce wireless driver, from Jurij
    Smakov.

 2) Fix leak of tx_ring and tx_cq due to overwriting in mlx4 driver,
    from Martin KaFai Lau.

 3) Need to reference count PHY driver module when it is attached, from
    Mao Wenan.

 4) Don't do zero length vzalloc() in ethtool register dump, from
    Stanislaw Gruszka.

 5) Defer net_disable_timestamp() to a workqueue to get out of locking
    issues, from Eric Dumazet.

 6) We cannot drop the SKB dst when IP options refer to them, fix also
    from Eric Dumazet.

 7) Incorrect packet header offset calculations in ip6_gre, again from
    Eric Dumazet.

 8) Missing tcp_v6_restore_cb() causes use-after-free, from Eric too.

 9) tcp_splice_read() can get into an infinite loop with URG, and hey
    it's from Eric once more.

10) vnet_hdr_sz can change asynchronously, so read it once during
    decision making in macvtap and tun, from Willem de Bruijn.

11) Can't use kernel stack for DMA transfers in USB networking drivers,
    from Ben Hutchings.

12) Handle csum errors properly in UDP by calling the proper destructor,
    from Eric Dumazet.

13) For non-deterministic softirq run when scheduling NAPI from a
    workqueue in mlx4, from Benjamin Poirier.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
  sctp: check af before verify address in sctp_addr_id2transport
  sctp: avoid BUG_ON on sctp_wait_for_sndbuf
  mlx4: Invoke softirqs after napi_reschedule
  udp: properly cope with csum errors
  catc: Use heap buffer for memory size test
  catc: Combine failure cleanup code in catc_probe()
  rtl8150: Use heap buffers for all register access
  pegasus: Use heap buffers for all register access
  macvtap: read vnet_hdr_size once
  tun: read vnet_hdr_sz once
  tcp: avoid infinite loop in tcp_splice_read()
  hns: avoid stack overflow with CONFIG_KASAN
  ipv6: Fix IPv6 packet loss in scenarios involving roaming + snooping switches
  ipv6: tcp: add a missing tcp_v6_restore_cb()
  nl80211: Fix mesh HT operation check
  mac80211: Fix adding of mesh vendor IEs
  mac80211: Allocate a sync skcipher explicitly for FILS AEAD
  mac80211: Fix FILS AEAD protection in Association Request frame
  ip6_gre: fix ip6gre_err() invalid reads
  netlabel: out of bound access in cipso_v4_validate()
  ...

Commit 6326fec1 ("mm: Use owner_priv bit for PageSwapCache, valid
when PageSwapBacked") aliased PG_swapcache to PG_owner_priv_1 (and
depending on PageSwapBacked being true).

As a result, the KPF_SWAPCACHE bit in '/proc/kpageflags' should now be
synthesized, instead of being shown on unrelated pages which just happen
to have PG_owner_priv_1 set.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 6f29a130 ("sctp: sctp_addr_id2transport should verify the
addr before looking up assoc") invoked sctp_verify_addr to verify the
addr.

But it didn't check af variable beforehand, once users pass an address
with family = 0 through sockopt, sctp_get_af_specific will return NULL
and NULL pointer dereference will be caused by af->sockaddr_len.

This patch is to fix it by returning NULL if af variable is NULL.

Fixes: 6f29a130 ("sctp: sctp_addr_id2transport should verify the addr before looking up assoc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Jo-Philipp Wich <jo@mein.io>
Fixes: 9aed02fe ("ARC: [arcompact] handle unaligned access delay slot")
Cc: linux-kernel@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Alexander Popov reported that an application may trigger a BUG_ON in
sctp_wait_for_sndbuf if the socket tx buffer is full, a thread is
waiting on it to queue more data and meanwhile another thread peels off
the association being used by the first thread.

This patch replaces the BUG_ON call with a proper error handling. It
will return -EPIPE to the original sendmsg call, similarly to what would
have been done if the association wasn't found in the first place.
Acked-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4 may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame and the following message may be logged:
NOHZ: local_softirq_pending 08

The problem is the same as what was described in commit ec13ee80
("virtio_net: invoke softirqs after __napi_schedule") and this patch
applies the same fix to mlx4.

Fixes: 07841f9d ("net/mlx4_en: Schedule napi when RX buffers allocation fails")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry reported that UDP sockets being destroyed would trigger the
WARN_ON(atomic_read(&sk->sk_rmem_alloc)); in inet_sock_destruct()

It turns out we do not properly destroy skb(s) that have wrong UDP
checksum.

Thanks again to syzkaller team.

Fixes : 7c13f97f ("udp: do fwd memory scheduling on dequeue")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
net: Fix on-stack USB buffers

Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).  This
series fixes all the instances I could find where USB networking
drivers do that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
References: https://bugs.debian.org/852556Reported-by: Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org>
Tested-by: Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Willem de Bruijn says:

====================
read vnet_hdr_sz once

Tuntap devices allow concurrent use and update of field vnet_hdr_sz.
Read the field once to avoid TOCTOU.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.

Macvtap functions read the value once, but unless READ_ONCE is used,
the compiler may ignore this and read multiple times. Enforce a single
read and locally cached value to avoid updates between test and use.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.

Read this value once and cache locally, as it can be updated between
the test and use (TOCTOU).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Splicing from TCP socket is vulnerable when a packet with URG flag is
received and stored into receive queue.

__tcp_splice_read() returns 0, and sk_wait_data() immediately
returns since there is the problematic skb in queue.

This is a nice way to burn cpu (aka infinite loop) and trigger
soft lockups.

Again, this gem was found by syzkaller tool.

Fixes: 9c55e01c ("[TCP]: Splice receive support.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov  <dvyukov@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libnvdimm fixes from Dan Williams:
 "None of these are showstoppers for 4.10 and could wait for 4.11 merge
  window, but they are low enough risk for this late in the cycle and
  the fixes have waiting users . They have received a build success
  notification from the 0day robot, pass the latest ndctl unit tests,
  and appeared in next:

   - Fix a crash that can result when SIGINT is sent to a process that
     is awaiting completion of an address range scrub command. We were
     not properly cleaning up the workqueue after
     wait_event_interruptible().

   - Fix a memory hotplug failure condition that results from not
     reserving enough space out of persistent memory for the memmap. By
     default we align to 2M allocations that the memory hotplug code
     assumes, but if the administrator specifies a non-default
     4K-alignment then we can fail to correctly size the reservation.

   - A one line fix to improve the predictability of libnvdimm block
     device names. A common operation is to reconfigure /dev/pmem0 into
     a different mode. For example, a reconfiguration might set a new
     mode that reserves some of the capacity for a struct page memmap
     array. It surprises users if the device name changes to
     "/dev/pmem0.1" after the mode change and then back to /dev/pmem0
     after a reboot.

   - Add 'const' to some function pointer tables"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm, pfn: fix memmap reservation size versus 4K alignment
  acpi, nfit: fix acpi_nfit_flush_probe() crash
  libnvdimm, namespace: do not delete namespace-id 0
  nvdimm: constify device_type structures

Pull power management fixes from Rafael Wysocki:
 "These add a quirk to intel_pstate to work around a firmware setting
  that leads to frequency scaling issues (discovered recently) on some
  Intel Kaby Lake processors, fix up the recently added brcmstb-avs
  cpufreq driver and avoid false-positive warnings from the runtime PM
  framework triggered by recent changes in i915.

  Specifics:

   - Add an intel_pstate driver quirk to work around a firmware setting
     that leads to frequency scaling issues on desktop Intel Kaby Lake
     processors in some configurations if the hardware-managed P-states
     (HWP) feature is in use (Srinivas Pandruvada)

   - Fix up the recently added brcmstb-avs cpufreq driver: fix a bug
     related to system suspend and change the sysfs interface to match
     the user space expectations (Markus Mayer)

   - Modify the runtime PM framework to avoid false-positive warnings
     from the might_sleep_if() assertions in it (Rafael Wysocki)"

* tag 'pm-4.10-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / runtime: Avoid false-positive warnings from might_sleep_if()
  cpufreq: intel_pstate: Disable energy efficiency optimization
  cpufreq: brcmstb-avs-cpufreq: properly retrieve P-state upon suspend
  cpufreq: brcmstb-avs-cpufreq: extend sysfs entry brcm_avs_pmap

Pull device mapper fixes from Mike Snitzer:

 - a fix for a race in .request_fn request-based DM request handling vs
   DM device destruction

 - an RCU fix for dm-crypt's kernel keyring support that was included in
   4.10-rc1

 - a -Wbool-operation warning fix for DM multipath

* tag 'dm-4.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm crypt: replace RCU read-side section with rwsem
  dm rq: cope with DM device destruction while in dm_old_request_fn()
  dm mpath: cleanup -Wbool-operation warning in choose_pgpath()

Pull media fixes from Mauro Carvalho Chehab:
 "A few documentation fixes at CEC (with got promoted from staging for
  4.10), and one fix on its core."

* tag 'media/v4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] cec: fix wrong last_la determination
  [media] cec-intro.rst: mention the v4l-utils package and CEC utilities
  [media] cec rst: remove "This API is not yet finalized" notice

Pull crypto fixes from Herbert Xu:

 - use-after-free in algif_aead

 - modular aesni regression when pcbc is modular but absent

 - bug causing IO page faults in ccp

 - double list add in ccp

 - NULL pointer dereference in qat (two patches)

 - panic in chcr

 - NULL pointer dereference in chcr

 - out-of-bound access in chcr

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: chcr - Fix key length for RFC4106
  crypto: algif_aead - Fix kernel panic on list_del
  crypto: aesni - Fix failure when pcbc module is absent
  crypto: ccp - Fix double add when creating new DMA command
  crypto: ccp - Fix DMA operations when IOMMU is enabled
  crypto: chcr - Check device is allocated before use
  crypto: chcr - Fix panic on dma_unmap_sg
  crypto: qat - zero esram only for DH85x devices
  crypto: qat - fix bar discovery for c62x

The use of ACCESS_ONCE() looks like a micro-optimization to force gcc to use
an indexed load for the register address, but it has an absolutely detrimental
effect on builds with gcc-5 and CONFIG_KASAN=y, leading to a very likely
kernel stack overflow aside from very complex object code:

hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_update_stats':
hisilicon/hns/hns_dsaf_gmac.c:419:1: error: the frame size of 2912 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_reset_common':
hisilicon/hns/hns_dsaf_ppe.c:390:1: error: the frame size of 1184 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_get_regs':
hisilicon/hns/hns_dsaf_ppe.c:621:1: error: the frame size of 3632 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_common_regs':
hisilicon/hns/hns_dsaf_rcb.c:970:1: error: the frame size of 2784 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_get_regs':
hisilicon/hns/hns_dsaf_gmac.c:641:1: error: the frame size of 5728 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_ring_regs':
hisilicon/hns/hns_dsaf_rcb.c:1021:1: error: the frame size of 2208 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_comm_init':
hisilicon/hns/hns_dsaf_main.c:1209:1: error: the frame size of 1904 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_xgmac.c: In function 'hns_xgmac_get_regs':
hisilicon/hns/hns_dsaf_xgmac.c:748:1: error: the frame size of 4704 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_update_stats':
hisilicon/hns/hns_dsaf_main.c:2420:1: error: the frame size of 1088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_regs':
hisilicon/hns/hns_dsaf_main.c:2753:1: error: the frame size of 10768 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

This does not seem to happen any more with gcc-7, but removing the ACCESS_ONCE
seems safe anyway and it avoids a serious issue for some people. I have verified
that with gcc-5.3.1, the object code we get is better in the new version
both with and without CONFIG_KASAN, as we no longer allocate a 1344 byte
stack frame for hns_dsaf_get_regs() but otherwise have practically identical
object code.

With gcc-7.0.0, removing ACCESS_ONCE has no effect, the object code is already
good either way.

This patch is probably not urgent to get into 4.11 as only KASAN=y builds
with certain compilers are affected, but I still think it makes sense to
backport into older kernels.

Cc: stable@vger.kernel.org
Fixes: 511e6bc0 ("net: add Hisilicon Network Subsystem DSAF support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When for instance a mobile Linux device roams from one access point to
another with both APs sharing the same broadcast domain and a
multicast snooping switch in between:

1)    (c) <~~~> (AP1) <--[SSW]--> (AP2)

2)              (AP1) <--[SSW]--> (AP2) <~~~> (c)

Then currently IPv6 multicast packets will get lost for (c) until an
MLD Querier sends its next query message. The packet loss occurs
because upon roaming the Linux host so far stayed silent regarding
MLD and the snooping switch will therefore be unaware of the
multicast topology change for a while.

This patch fixes this by always resending MLD reports when an interface
change happens, for instance from NO-CARRIER to CARRIER state.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2017-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.10

Only one important fix for rtlwifi which fixes a regression introduced
in 4.9 and which caused problems for many users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2017-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
A few simple fixes:
 * fix FILS AEAD cipher usage to use the correct AAD vectors
   and to use synchronous algorithms
 * fix using mesh HT operation data from userspace
 * fix adding mesh vendor elements to beacons & plink frames
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry reported use-after-free in ip6_datagram_recv_specific_ctl()

A similar bug was fixed in commit 8ce48623 ("ipv6: tcp: restore
IP6CB for pktoptions skbs"), but I missed another spot.

tcp_v6_syn_recv_sock() can indeed set np->pktoptions from ireq->pktopts

Fixes: 971f10ec ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* pm-core-fixes:
  PM / runtime: Avoid false-positive warnings from might_sleep_if()

* pm-cpufreq-fixes:
  cpufreq: intel_pstate: Disable energy efficiency optimization
  cpufreq: brcmstb-avs-cpufreq: properly retrieve P-state upon suspend
  cpufreq: brcmstb-avs-cpufreq: extend sysfs entry brcm_avs_pmap

A previous change to fix checks for NL80211_MESHCONF_HT_OPMODE
missed setting the flag when replacing FILL_IN_MESH_PARAM_IF_SET
with checking codes. This results in dropping the received HT
operation value when called by nl80211_update_mesh_config(). Fix
this by setting the flag properly.

Fixes: 9757235f ("nl80211: correct checks for NL80211_MESHCONF_HT_OPMODE value")
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[rewrite commit message to use Fixes: line]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The function ieee80211_ie_split_vendor doesn't return 0 on errors. Instead
it returns any offset < ielen when WLAN_EID_VENDOR_SPECIFIC is found. The
return value in mesh_add_vendor_ies must therefore be checked against
ifmsh->ie_len and not 0. Otherwise all ifmsh->ie starting with
WLAN_EID_VENDOR_SPECIFIC will be rejected.

Fixes: 082ebb0c ("mac80211: fix mesh beacon format")
Signed-off-by: Thorsten Horstmann <thorsten@defutech.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[sven@narfation.org: Add commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The skcipher could have been of the async variant which may return from
skcipher_encrypt() with -EINPROGRESS after having queued the request.
The FILS AEAD implementation here does not have code for dealing with
that possibility, so allocate a sync cipher explicitly to avoid
potential issues with hardware accelerators.

This is based on the patch sent out by Ard.

Fixes: 39404fee ("mac80211: FILS AEAD protection for station mode association frames")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Incorrect num_elem parameter value (1 vs. 5) was used in the
aes_siv_encrypt() call. This resulted in only the first one of the five
AAD vectors to SIV getting included in calculation. This does not
protect all the contents correctly and would not interoperate with a
standard compliant implementation.

Fix this by using the correct number. A matching fix is needed in the AP
side (hostapd) to get FILS authentication working properly.

Fixes: 39404fee ("mac80211: FILS AEAD protection for station mode association frames")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Andrey Konovalov reported out of bound accesses in ip6gre_err()

If GRE flags contains GRE_KEY, the following expression
*(((__be32 *)p) + (grehlen / 4) - 1)

accesses data ~40 bytes after the expected point, since
grehlen includes the size of IPv6 headers.

Let's use a "struct gre_base_hdr *greh" pointer to make this
code more readable.

p[1] becomes greh->protocol.
grhlen is the GRE header length.

Fixes: c12b395a ("gre: Support GRE over IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzkaller found another out of bound access in ip_options_compile(),
or more exactly in cipso_v4_validate()

Fixes: 20e2a864 ("cipso: handle CIPSO options correctly when NetLabel is disabled")
Fixes: 446fda4f ("[NetLabel]: CIPSOv4 engine")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov  <dvyukov@google.com>
Cc: Paul Moore <paul@paul-moore.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrey Konovalov got crashes in __ip_options_echo() when a NULL skb->dst
is accessed.

ipv4_pktinfo_prepare() should not drop the dst if (evil) IP options
are present.

We could refine the test to the presence of ts_needtime or srr,
but IP options are not often used, so let's be conservative.

Thanks to syzkaller team for finding this bug.

Fixes: d826eb14 ("ipv4: PKTINFO doesnt need dst reference")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When vmemmap_populate() allocates space for the memmap it does so in 2MB
sized chunks. The libnvdimm-pfn driver incorrectly accounts for this
when the alignment of the device is set to 4K. When this happens we
trigger memory allocation failures in altmap_alloc_block_buf() and
trigger warnings of the form:

 WARNING: CPU: 0 PID: 3376 at arch/x86/mm/init_64.c:656 arch_add_memory+0xe4/0xf0
 [..]
 Call Trace:
  dump_stack+0x86/0xc3
  __warn+0xcb/0xf0
  warn_slowpath_null+0x1d/0x20
  arch_add_memory+0xe4/0xf0
  devm_memremap_pages+0x29b/0x4e0

Fixes: 315c5625 ("libnvdimm, pfn: add 'align' attribute, default to HPAGE_SIZE")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Pull irq fixes from Thomas Gleixner:

 - Prevent double activation of interrupt lines, which causes problems
   on certain interrupt controllers

 - Handle the fallout of the above because x86 (ab)uses the activation
   function to reconfigure interrupts under the hood.

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/irq: Make irq activate operations symmetric
  irqdomain: Avoid activating interrupts more than once

Pull KVM fix from Radim Krčmář:
 "Fix a regression that prevented migration between hosts with different
  XSAVE features even if the missing features were not used by the guest
  (for stable)"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: do not save guest-unsupported XSAVE state