Add a MCI util function to send wlan channel info to BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a utility function to set bluetooth version and remove
MCI_STATE_SET_BT_COEX_VERSION.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add utility functions to get and test GPM offset and
remove MCI_STATE*_GPM_OFFSET states.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up

	Call Trace:
	[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
	[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
	[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
	[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
	[<ffffffff810744fe>] process_one_work+0x11e/0x470
	[<ffffffff8107530f>] worker_thread+0x15f/0x360
	[<ffffffff810751b0>] ? manage_workers+0x230/0x230
	[<ffffffff81079af3>] kthread+0x93/0xa0
	[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
	[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
	[<ffffffff815fd3a0>] ? gs_change+0x13/0x13

ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.

fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Reset duty cycle before updating btcoex scheme. Otherwise duty cycle
  reaches max limit and never be reduced again
* Adjust duty cycle with proper BDR profile value
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As btcoex scheme updation might sleep, remove the function call
from tasklet context and queue it up as a separate work.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

btcoex periord is converted into micro seconds during initialization
and converted back to milli seconds while starting timer. As MCI code
handles btcoex period in msec, lets keep the btcoex timer in msec and
convert them into other form whenever needed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch simplifies profile management utility functions.

* Separate find_profile from add/del functions
* Return correct values when the profile list is empty or
  profile is ot found
* flush the profiles when there are entries in the list
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

let us process MCI interrupts only when BTCOEX is enabled to avoid
processing bogus interrupts.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After a full reset, mci_reset will put LNA update to the setting
for 2G mode. Those registers need to be forced to update when
the channel is in 5G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Both "MAC Warm Reset" and "MCI Reset Rx" will reset GPM HW write_ptr.
We should check software cached write_ptr against HW write_ptr before
reset. Otherwise the pending DMA data will be lost.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The HW statemachine is sometimes found stuck in the state
WL_LNA_CTRL_DISABLE when BT is in sleep, which will cause
TX_HOLD always asserted and resmgr stuck in PENDING_TX state
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Not doing so, could cause imbalance in powersave count.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Choose legacy rate as the last rate of Multi Rate Retry series
if and only if the last selected rate is MCS and having higher
PER rate. The current code fills a legacy rate as last one even
though the previous rates in the series are having good PER value.
This could limit the aggregation that affects the uplink performance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adjust quick_drop value in the baseband AGC register to
improve RX in HT20 mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The structure brcmf_sdio contains a number of counters that are useful
for debugging. These were not available in user-space. This patch
exposes them in debugfs under the filename 'counters'.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds debugfs support to brcmfmac. It provide helper functions
to setup the debugfs folder structure for the driver, which has following
hierarchy:

<debugfs_mount>/brcmfmac/<dev_name>/

ie.: /sys/kernel/debug/brcmfmac/mmc0:0001:2/

The new source file provides functions to create and remove the two
folders and a function to retrieve the device-specific folder so files
can be created in it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes potential NULL pointer dereference in ampdu. This
was found running smatch static code checker. Smatch warning says:

drivers/net/wireless/brcm80211/brcmsmac/ampdu.c:741 brcms_c_sendampdu()
	 warn: variable dereferenced before check 'p'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The function brcms_set_hint() does not add any functionality
so regulatory_hint() can be called directly. The error value
has been removed from the message when regulatory_hint() fails.
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This flow can actually happen due to a corner case in
mac80211: the station is deleted before we get a chance
to reclaim all the packets in flight in AGG queue.
The tid_data for this station is zeroed, and we lose
the match with the Tx queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since request_module_nowait() can't be backported
use request_module() instead -- we don't need the
asynchronous behaviour of request_module_nowait()
here since we're running in the firmware request
work struct.
Tested-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Due to commit 26a7ca9a ("iwlwifi: refactor EEPROM
reading/parsing") adding a new parameter, while commit
d2c8b15d ("iwlwifi: use correct supported firmware
for 6035 and 6000g2") added a new device structure we
need to add the parameter to the new device structure
to make 6035 device work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For AGG queues, we must match between the WiFi sequence
number and the TFD number. This is a HW (SCD) requirement.

This is a take two of my

    iwlwifi: add debug in Tx path in AGG flow

    This will allow us to catch bad cases in which the packets aren't in
    the right place on the ring.

which disappeared during code move.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In fragmentation we don't update the write pointer of the
HW immediately. So we shouldn't modify the timer in that
case.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

CMD_SYNC is zero so the if (cmd->flags & CMD_SYNC) is never true and we
never check the assertion.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since the queue gets stuck from time to time, we are trying
to get as much information as we can when this occurs.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When the driver is built into the kernel instead of a module
when the system boots it results in a panic. The order things are built in
results in their initialization order when built into the kernel. Wifi
has to be initialized before mvm or dvm.
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Tested-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Brandon Misemer <brandon.misemer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Using the driver_data area in ieee80211_tx_info which
resides in the CB overrides the info->control field.
Add a comment to prevent mistakes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This locking isn't needed. The only locking we need is when
we access prph registers but there is already a separate
lock for that.
Since we haven't returned from the mac80211's
IEEE80211_AMPDU_TX_OPERATIONAL ampdu_action, we cannot
receive any Tx frame for that sta / tid while enabling the
queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This is not needed, we just need to tell the SCD not to use
that queue. We will reconfigure that queue when we will use
it again.

Clean up a bit the code on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Print some more info from the SCD's SRAM and dump the TRB
from the FH.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Change its name to better reflect this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This macro gets the bufsize in bytes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add locking to the dynamic loading code to prevent
corrupting the list if multiple device ever init at
the same time (which cannot happen for multiple PCI
devices, but could happen when different busses init
concurrently.)

Also remove a device from the list when it stops so
the list isn't left corrupted, including a fix from
Don to not crash when it was never added.
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Tested-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Conflicts:
	MAINTAINERS
	drivers/net/wireless/iwlwifi/pcie/trans.c

14e4:432c is found on some bcm63xx devices. The device is working fine
with b43.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MSI is enabled by default for most of the 4th generation
chips. Add this for AR9462 - this fixes PowerSave operation,
the chip was not entering Network-Sleep mode earlier.
With proper powering down of the MAC now, power consumption
in associated state is reduced considerably.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently 4 channels are scanned per scan command. if scan request
is issued by user during Tx traffic, radio will be out of channel
for "4 * per_chan_scan_time" for each scan command and will not be
able to receive Rx packets. This adds delay in data traffic. We can
minimize it by reducing number of channels scanned per scan command
in this scenario.

We can not always scan 1 channel per scan command due to limitation
of number of command buffers. So we add code to decide number of
channels scanned per scan command in associated state.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>