The HP mv2120 has several LEDs that are controlled through gpio.
Export the health LED, the red SATA LEDs as well as two gpios
that control the brightness of _all_ LEDs to userland.  The
Ethernet and power LEDs can't be controlled through gpio and the
blue SATA LEDs are handled via the SATA driver.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>

This patch adds support for the Marvell Orion-VoIP RD-88F5181L-FXO
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Signed-off-by: Nicolas Pitre <nico@marvell.com>

This patch adds support for the Marvell Orion-VoIP RD2-88F5181L-GE
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Update mach-types.  Remove invalid or incorrect entries.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Some SoCs need a different chip_delay value.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

The Cardbus connector does not have an IDSEL signal, and Cardbus
cards are always the intended target of configuration transactions
on their local PCI bus.  This means that if the Orion's PCI bus
signals are hooked up to a Cardbus slot, the same set of PCI
functions will will appear 31 times, for each of the PCI device
IDs 1-31 (ID 0 is the host bridge).

This patch adds a function to the Orion PCI handling code that board
support code can call to enable Cardbus mode.  When Cardbus mode is
enabled, configuration transactions on the PCI local bus are only
allowed to PCI IDs 0 (host bridge) and 1 (cardbus device).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

This patch allows booting Kirkwood with the L2 in writeback mode,
by reading the WT override bit from the L2 config register and
passing that into the Feroceon L2 init routine, instead of assuming
that the WT override bit will always be set
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

In some cases, compilation of the tsx09 common file was failing due
to an incomplete list of includes.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

After Jean Delvare's change "i2c: Convert most new-style drivers
to use module aliasing" (3760f736),
loading rtc-xxx from platform code fails.  Update mv2120-setup.c so
that the driver is loaded correctly.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Kurobox Pro/Linkstation Pro devices use a microcontroller connected
to UART1.  As most of the communication with this microcontroller is
done from userland (power button detection, fan speed ...), the setup
file has to make UART1 available from userland.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Eliminate NULL test after alloc_bootmem in iosapic_alloc_rte()
  [IA64] Handle count==0 in sn2_ptc_proc_write()
  [IA64] Fix boot failure on ia64/sn2

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  [GFS2] fix gfs2 block allocation (cleaned up)
  [GFS2] BUG: unable to handle kernel paging request at ffff81002690e000

* 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: Remove now unused structs from kvm_para.h
  x86: KVM guest: Use the paravirt clocksource structs and functions
  KVM: Make kvm host use the paravirt clocksource structs
  x86: Make xen use the paravirt clocksource structs and functions
  x86: Add structs and functions for paravirt clocksource
  KVM: VMX: Fix host msr corruption with preemption enabled
  KVM: ioapic: fix lost interrupt when changing a device's irq
  KVM: MMU: Fix oops on guest userspace access to guest pagetable
  KVM: MMU: large page update_pte issue with non-PAE 32-bit guests (resend)
  KVM: MMU: Fix rmap_write_protect() hugepage iteration bug
  KVM: close timer injection race window in __vcpu_run
  KVM: Fix race between timer migration and vcpu migration

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  Revert "[WATCHDOG] hpwdt: Add CFLAGS to get driver working"

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  xen: remove support for non-PAE 32-bit

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  kgdb: sparse fix
  kgdb: documentation update - remove kgdboe

On 9xx chips, bus mastering needs to be enabled at resume time for much of the
chip to function.  With this patch, vblank interrupts will work as expected
on resume, along with other chip functions.   Fixes kernel bugzilla #10844.
Signed-off-by: Jie Luo <clotho67@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The kvm_* structs are obsoleted by the pvclock_* ones.
Now all users have been switched over and the old structs
can be dropped.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

This patch updates the kvm host code to use the pvclock structs
and functions, thereby making it compatible with Xen.

The patch also fixes an initialization bug: on SMP systems the
per-cpu has two different locations early at boot and after CPU
bringup.  kvmclock must take that in account when registering the
physical address within the host.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

This patch updates the kvm host code to use the pvclock structs.
It also makes the paravirt clock compatible with Xen.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

This patch updates the xen guest to use the pvclock structs
and helper functions.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

This patch adds structs for the paravirt clocksource ABI
used by both xen and kvm (pvclock-abi.h).

It also adds some helper functions to read system time and
wall clock time from a paravirtual clocksource (pvclock.[ch]).
They are based on the xen code.  They are enabled using
CONFIG_PARAVIRT_CLOCK.

Subsequent patches of this series will put the code in use.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

This patch fixes bz 450641.

This patch changes the computation for zero_metapath_length(), which it
renames to metapath_branch_start(). When you are extending the metadata
tree, The indirect blocks that point to the new data block must either
diverge from the existing tree either at the inode, or at the first
indirect block. They can diverge at the first indirect block because the
inode has room for 483 pointers while the indirect blocks have room for
509 pointers, so when the tree is grown, there is some free space in the
first indirect block. What metapath_branch_start() now computes is the
height where the first indirect block for the new data block is located.
It can either be 1 (if the indirect block diverges from the inode) or 2
(if it diverges from the first indirect block).
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

As noted by Akinobu Mita alloc_bootmem and related functions never return
NULL and always return a zeroed region of memory.  Thus a NULL test or
memset after calls to these functions is unnecessary.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tony Luck <tony.luck@intel.com>

The fix applied in e0c6d97c
"security hole in sn2_ptc_proc_write" didn't take into account
the case where count==0 (which results in a buffer underrun
when adding the trailing '\0').  Thanks to Andi Kleen for
pointing this out.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Call check_sal_cache_flush() after platform_setup() as
check_sal_cache_flush() now relies on being able to call platform
vector code.

Problem was introduced by: 3463a93d
"Update check_sal_cache_flush to use platform_send_ipi()"
Signed-off-by: Jes Sorensen <jes@sgi.com>
Tested-by: Alex Chiang: <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

- Fix warning reported by sparse
kernel/kgdb.c:1502:6: warning: symbol 'kgdb_console_write' was not declared.
	Should it be static?
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

kgdboe is not presently included kgdb, and there should be no
references to it.

Also fix the tcp port terminal connection example.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

Non-PAE operation has been deprecated in Xen for a while, and is
rarely tested or used.  xen-unstable has now officially dropped
non-PAE support.  Since Xen/pvops' non-PAE support has also been
broken for a while, we may as well completely drop it altogether.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

This patch fixes bugzilla bug bz448866: gfs2: BUG: unable to
handle kernel paging request at ffff81002690e000.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

After Linus fixed the inline assembly, the CFLAGS option is not
needed anymore.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Switching msrs can occur either synchronously as a result of calls to
the msr management functions (usually in response to the guest touching
virtualized msrs), or asynchronously when preempting a kvm thread that has
guest state loaded.  If we're unlucky enough to have the two at the same
time, host msrs are corrupted and the machine goes kaput on the next syscall.

Most easily triggered by Windows Server 2008, as it does a lot of msr
switching during bootup.
Signed-off-by: Avi Kivity <avi@qumranet.com>

The ioapic acknowledge path translates interrupt vectors to irqs.  It
currently uses a first match algorithm, stopping when it finds the first
redirection table entry containing the vector.  That fails however if the
guest changes the irq to a different line, leaving the old redirection table
entry in place (though masked).  Result is interrupts not making it to the
guest.

Fix by always scanning the entire redirection table.
Signed-off-by: Avi Kivity <avi@qumranet.com>

KVM has a heuristic to unshadow guest pagetables when userspace accesses
them, on the assumption that most guests do not allow userspace to access
pagetables directly. Unfortunately, in addition to unshadowing the pagetables,
it also oopses.

This never triggers on ordinary guests since sane OSes will clear the
pagetables before assigning them to userspace, which will trigger the flood
heuristic, unshadowing the pagetables before the first userspace access. One
particular guest, though (Xenner) will run the kernel in userspace, triggering
the oops.  Since the heuristic is incorrect in this case, we can simply
remove it.
Signed-off-by: Avi Kivity <avi@qumranet.com>

kvm_mmu_pte_write() does not handle 32-bit non-PAE large page backed
guests properly. It will instantiate two 2MB sptes pointing to the same
physical 2MB page when a guest large pte update is trapped.

Instead of duplicating code to handle this, disallow directory level
updates to happen through kvm_mmu_pte_write(), so the two 2MB sptes
emulating one guest 4MB pte can be correctly created by the page fault
handling path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>