Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Octeon SMI/MDIO interfaces can do clause 45 communications, so
implement this in the driver.

Also fix some comment formatting to make it consistent and to comply
with the netdev style.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_queue_xmit() will return a positive value if the packet could not be
queued, often because the real network device (in our case the mac802154
wpan device) has its queue stopped.  lowpan_xmit() should handle the
positive return code (for the debug statement) and return that value to
the higher layer so the higher layer will retry sending the packet.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Increase the buffer length from 10 to 300 packets. Consider that traffic on
mac802154 devices will often be 6LoWPAN, and a full-length (1280 octet)
IPv6 packet will fragment into 15 6LoWPAN fragments (because the MTU of
IEEE 802.15.4 is 127).  A 300-packet queue is really 20 full-length IPv6
packets.

With a queue length of 10, an entire IPv6 packet was unable to get queued
at one time, causing fragments to be dropped, and making reassembly
impossible.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netif_stop_queue() and netif_wake_queue() to control the flow of
packets to mac802154 devices.  Since many IEEE 802.15.4 devices have no
output buffer, and since the mac802154 xmit() function is designed to
block, netif_stop_queue() is called after each packet.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ops->xmit() fails, drop the packet. Devices which support hardware
ack and retry (which include all devices currently supported by mainline),
will automatically retry sending the packet (in the hardware) up to 3
times, per the 802.15.4 spec.  There is no need, and it is incorrect to
try to do it in mac802154.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

(Resend with a better changelog)

garp_pdu_queue() should ways be called with this spin lock.
garp_uninit_applicant() only holds rtnl lock which is not
enough here.  A possible race can happen as garp_pdu_rcv()
is called in BH context:

	garp_pdu_rcv()
	  |->garp_pdu_parse_msg()
	    |->garp_pdu_parse_attr()
	      |-> garp_gid_event()

Found by code inspection.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Ward <david.ward@ll.mit.edu>
Cc: "Jorge Boncompte [DTI2]" <jorge@dti2.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a simple test case that probes the packet socket's
TPACKET_V1, TPACKET_V2 and TPACKET_V3 behavior regarding mmap(2)'ed
I/O for a small burst of 100 packets. The test currently runs for ...

  TPACKET_V1: RX_RING, TX_RING
  TPACKET_V2: RX_RING, TX_RING
  TPACKET_V3: RX_RING

... and will output on success:

  test: TPACKET_V1 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
  test: TPACKET_V1 with PACKET_TX_RING .................... 100 pkts (9600 bytes)
  test: TPACKET_V2 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
  test: TPACKET_V2 with PACKET_TX_RING .................... 100 pkts (9600 bytes)
  test: TPACKET_V3 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
  OK. All tests passed

Reusable parts of psock_fanout.c have been put into a psock_lib.h
file for common usage. Test case successfully tested on x86_64.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch bypasses vxlan encapsulation if the destination vxlan
endpoint is a local device.

Changes since v1: added missing check for vxlan_find_vni() failure
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When our getdcbx entry is called, DCB_CAP_DCBX_HOST should be advertized too.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable the DCB ETS ops only when supported by the firmware. For older firmware/cards
which don't support ETS, advertize only PFC DCB ops.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added readable description for the DPDP and port sensing device capabilities.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new chip for RTL8106E series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The suggestion as following:
- initial settings or default settings
- rtl_hw_start_xxx. rtl_hw_start_xxx may change some default settings.
- enable tx/rx. This has to be after the above two steps.
- rtl_set_rx_mode. AcceptXXXs have to be enabled after enabling tx/rx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new chip for RTL8111G series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- replace rtl8168g-1.fw with rtl8168g-2.fw which support new method.
- fix PHY power down is useless.
- disable rx early which causes the rx abnormal.
- enable auto fifo.
- set 10M IFG to default value.
- fix the conflict between jumbo frame and flow control.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove useless action PHY_READ_EFUSE, PHY_READ_MAC_BYTE, PHY_WRITE_MAC_BYTE,
PHY_WRITE_ERI_WORD. And define the new action PHY_MDIO_CHG.

PHY_MDIO_CHG is used to modify the mdio operation. By the way, the
firmware could support setting mac ocp.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the new settings and correct the wrong settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the current settings with rtl_writephy and rtl_readphy.
For the hardware, the settings are same with previous ones. This
make the setting method like the previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some codes are belong to binary codes and should be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains Netfilter and IPVS updates for
your net-next tree, most relevantly they are:

* Add net namespace support to NFLOG, ULOG and ebt_ulog and NFQUEUE.
  The LOG and ebt_log target has been also adapted, but they still
  depend on the syslog netnamespace that seems to be missing, from
  Gao Feng.

* Don't lose indications of congestion in IPv6 fragmentation handling,
  from Hannes Frederic Sowa.i

* IPVS conversion to use RCU, including some code consolidation patches
  and optimizations, also some from Julian Anastasov.

* cpu fanout support for NFQUEUE, from Holger Eitzenberger.

* Better error reporting to userspace when dropping packets from
  all our _*_[xfrm|route]_me_harder functions, from Patrick McHardy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This change brings netfilter reassembly logic on par with
reassembly.c. The corresponding change in net-next is
(eec2e618 ipv6: implement RFC3168 5.3 (ecn protection) for
ipv6 fragmentation handling)

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jesper Dangaard Brouer <jbrouer@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Now that this supports net namespace for nflog and nfqueue,
we can remove the global proc_net_netfilter which has no
clients anymore.

Based on patch from Gao feng.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This patch makes /proc/net/netfilter/nfnetlink_queue pernet.
Moreover, there's a pernet instance table and lock.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

After this patch, all nf_loggers support net namespace. Still
xt_LOG and ebt_log require syslog netns support.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This patch makes /proc/net/netfilter/nfnetlink_log pernet.
Moreover, there's a pernet instance table and lock.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add pernet support to ipt_ULOG by means of the new nf_log_set
function added in (30e0c6a6 netfilter: nf_log: prepare net
namespace support for loggers).

This patch also make ulog_buffers and netlink socket
nflognl per netns.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add pernet support to ebt_ulog by means of the new nf_log_set
function added in (30e0c6a6 netfilter: nf_log: prepare net
namespace support for loggers).

This patch also make ulog_buffers and netlink socket
ebtulognl per netns.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add pernet support to xt_LOG by means of the new nf_log_set
function added in (30e0c6a6 netfilter: nf_log: prepare net
namespace support for loggers).

Since syslog ns has yet not been implemented, we don't want
the containers to DDOS host's syslogd. So only enable ebt_log
only from init_net and wait for syslog ns support
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add pernet support to ebt_log by means of the new nf_log_set
function added in (30e0c6a6 netfilter: nf_log: prepare net
namespace support for loggers).

Since syslog ns has yet not been implemented, we don't want
the containers to DDOS host's syslogd. So only enable ebt_log
only from init_net and wait for syslog ns support.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This patch adds netns support to nf_log and it prepares netns
support for existing loggers. It is composed of four major
changes.

1) nf_log_register has been split to two functions: nf_log_register
   and nf_log_set. The new nf_log_register is used to globally
   register the nf_logger and nf_log_set is used for enabling
   pernet support from nf_loggers.

   Per netns is not yet complete after this patch, it comes in
   separate follow up patches.

2) Add net as a parameter of nf_log_bind_pf. Per netns is not
   yet complete after this patch, it only allows to bind the
   nf_logger to the protocol family from init_net and it skips
   other cases.

3) Adapt all nf_log_packet callers to pass netns as parameter.
   After this patch, this function only works for init_net.

4) Make the sysctl net/netfilter/nf_log pernet.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This patch makes this proc dentry pernet. So far only init_net
had a /proc/net/netfilter directory.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>