Skip to content

L
linux
Switch branch/tag
  1. 07 Apr, 2009 9 commits
    • Jens Axboe's avatar
      cfq-iosched: change dispatch logic to deal with single requests at the time · 2f5cb738
      Jens Axboe authored 
      The IO scheduler core calls into the IO scheduler dispatch_request hook
to move requests from the IO scheduler and into the driver dispatch
list. It only does so when the dispatch list is empty. CFQ moves several
requests to the dispatch list, which can cause higher latencies if we
suddenly have to switch to some important sync IO. Change the logic to
move one request at the time instead.

This should almost be functionally equivalent to what we did before,
except that we now honor 'quantum' as the maximum queue depth at the
device side from any single cfqq. If there's just a single active
cfqq, we allow up to 4 times the normal quantum.
Signed-off-by: default avatarJens Axboe <jens.axboe@oracle.com>
      2f5cb738
    • unsik Kim's avatar
      mflash: initial support · 3fbed4c6
      unsik Kim authored 
      This driver supports mflash IO mode for linux.

Mflash is embedded flash drive and mainly targeted mobile and consumer
electronic devices.

Internally, mflash has nand flash and other hardware logics and supports 2
different operation (ATA, IO) modes.  ATA mode doesn't need any new driver
and currently works well under standard IDE subsystem.  Actually it's one
chip SSD.  IO mode is ATA-like custom mode for the host that doesn't have
IDE interface.

Followings are brief descriptions about IO mode.
A. IO mode based on ATA protocol and uses some custom command. (read confirm,
write confirm)
B. IO mode uses SRAM bus interface.
C. IO mode supports 4kB boot area, so host can boot from mflash.

This driver is quitely similar to a standard ATA driver, but because of
following reasons it is currently seperated with ATA layer.

1. ATA layer deals standard ATA protocol.  ATA layer have many low-
   level device specific interface, but data transfer keeps ATA rule.
   But, mflash IO mode doesn't.

2. Even though currently not used in mflash driver code, mflash has
   some custom command and modes.  (nand fusing, firmware patch, etc) If
   this feature supported in linux kernel, ATA layer more altered.

3. Currently PATA platform device driver doesn't support interrupt.
   (I'm not sure) But, mflash uses interrupt (polling mode is just for
   debug).

4. mflash is somewhat under-develop product.  Even though some company
   already using mflash their own product, I think more time is needed for
   standardization of custom command and mode.  That time (maybe October)
   I will talk to with ATA people.  If they accept integration, I will
   integrate.
Signed-off-by: default avatarunsik Kim <donari75@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarJens Axboe <jens.axboe@oracle.com>
      3fbed4c6
    • Mike Miller's avatar
      cciss: change to discover first memory BAR · e1438581
      Mike Miller authored 
      Add a method for discovering the first memory BAR.  All Smart Array
controllers to date have always had the the memory BAR as the first BAR.
A new controller to be released later this year breaks that model.
Signed-off-by: default avatarMike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarJens Axboe <jens.axboe@oracle.com>
      e1438581
    • Mike Miller's avatar
      cciss: kernel scan thread for MSA2012 · 0a9279cc
      Mike Miller authored 
      The MSA2012 cannot inform the driver of configuration changes since all
management is out of band.  This is a departure from any storage we have
supported in the past.  We need some way to detect changes on the topology
so we implement this kernel thread.  In some instances there's nothing we
can do from the driver (like LUN failure) so just print out a message.  In
the case where logical volumes are added or deleted we call
rebuild_lun_table to refresh the driver's view of the world.
Signed-off-by: default avatarMike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarJens Axboe <jens.axboe@oracle.com>
      0a9279cc
    • Jens Axboe's avatar
      cciss: fix residual count for block pc requests · ac44e5b2
      Jens Axboe authored 
      We must complete the full request, so store the request count and then set
the ->data_len to the residual count from the hardware.
Signed-off-by: default avatarJens Axboe <jens.axboe@oracle.com>
      ac44e5b2
    • Jerome Marchand's avatar
      block: fix inconsistency in I/O stat accounting code · 26308eab
      Jerome Marchand authored 
      This forces in_flight to be zero when turning off or on the I/O stat
accounting and stops updating I/O stats in attempt_merge() when
accounting is turned off.
Signed-off-by: default avatarJerome Marchand <jmarchan@redhat.com>
Signed-off-by: default avatarJens Axboe <jens.axboe@oracle.com>
      26308eab
    • Jens Axboe's avatar
      block: elevator quiescing helpers · 6c7e8cee
      Jens Axboe authored 
      Simple helper functions to quiesce the request queue. These are
currently only used for switching IO schedulers on-the-fly, but
we can use them to properly switch IO accounting on and off as well.
Signed-off-by: default avatarJerome Marchand <jmarchan@redhat.com>
Signed-off-by: default avatarJens Axboe <jens.axboe@oracle.com>
      6c7e8cee
    • Trond Myklebust's avatar
      NFS: Fix a double free in nfs_parse_mount_options() · d508afb4
      Trond Myklebust authored 
      Due to an apparent typo, commit a67d18f8
(NFS: load the rpc/rdma transport module automatically) lead to the
'proto=' mount option doing a double free, while Opt_mountproto leaks a
string.
Signed-off-by: default avatarTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      d508afb4
    • Linus Torvalds's avatar
      ext3: make default data ordering mode configurable · bbae8bcc
      Linus Torvalds authored 
      This makes the defautl ext3 data ordering mode (when no explicit
ordering is set) configurable, so as to allow people to default to
'data=writeback' and get the resulting latency improvements.

This is a non-issue if a filesystem has been explicitly set to some
ordering (with 'tune2fs').
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      bbae8bcc
  3. 06 Apr, 2009 31 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7