This implements a pre-decoded wchan in /proc using kallsyms.  I.e.:

        [21:23:17]rml@phantasy:~$ cat /proc/1228/wchan
        wait4

Which, aside from being cool, means procps will not have to parse
Sysyem.map for each process.  In fact, procps will no longer require
System.map.

If CONFIG_KALLSYMS is not enabled, /proc/#/wchan does not exist to
conserve memory.  Regardless of CONFIG_KALLSYMS's value, the old wchan
field in /proc/#/stat still exists.

I have a procps patch I will merge once this is in your tree.

This adds hyper-threading information to /proc/cpuinfo, if relevant: the
physical processor id and the number of sibling units in this core.

The naming of the fields were debated a bit on lkml and the names below
offend the least number of people, do not break glibc, and are the same
as those in 2.4-ac.

This is in 2.4-ac, 2.5-mm, and vendor kernels from RedHat, SuSE, etc.

make x86_do_profile available when UP=y,LOCAL_APIC=n

From Bill Irwin

Optionally back priviled processes' shm with hugetlbfs.

One of the more common requests for and/or users of hugetlb interfaces
in general are databases using shm.  This patch exports functionality
mostly equivalent to tmpfs, adds the calling sequence to ipc/shm.c, and
hashes out a small support function in fs/hugetlbfs/inode.c so that shm
segments may be hugetlbpage-backed if userspace passes a flag to
shmget().

Access to this resource requires CAP_IPC_LOCK.

From Bill Irwin

Tiny hugetlbpage ram-backed filesystem.

Some way to export hugetlbfs through more standard system call
interfaces was needed, and hugetlbfs already had inodes with ratnodes
etc.  used to track offset -> page translations, so adding the rest of
a filesystem around it was easy and natural.  Most of it is identical
to ramfs, except ->f_op->mmap() is now just a wrapper around the
hugetlb_prefault() to fill in the VMA, and to simplify it,
->readpage(), ->prepare_write(), and ->commit_write() are omitted.

Permissions:

(1) check capable(CAP_IPC_LOCK) in ->f_ops->mmap
        This may be redundant but it errors out with less state to
        clean up and at least clarifies the fact that checks are
        being performed at the relevant entry points.

(2) check capable(CAP_IPC_LOCK) in hugetlbfs_zero_setup()
        This is called at shmget() time and is an actual potential
        security hole. hugetlb_prefault() does not perform this
        check itself, so it must be done here.

It's setting the page count on the wrong page.

huge_page_release()             -- hugepage refcounting
free_huge_page()                -- separates freeing from inode refcounting
unmap_hugepage_range()          -- unmapping refcounting hook when locked
zap_hugepage_range()            -- unmappping refcounting hook when unlocked
export setattr_mask()           -- hugetlbfs wants to call it
export destroy_inode()          -- hugetlbfs wants to use it
export unmap_vma()              -- hugetlbpage.c wants to use it
unlock_page() in hugetlbpage.c  -- fixes deadlock in hugetlbfs_truncate()

From Bill Irwin

Move hugetlb and hugetlbfs declarations into a dedicated header file.

Hugetlb's big #ifdeffed block in mm.h got a lot bigger with hugetlbfs.
This patch basically attempts to remove the noise from mm.h by simply
rearranging it into a new header, and fixing all users of hugetlb.

In order for hugetlbfs to operate, prefaulting the vma at mmap()-time
while simultaneously instantiating and performing lookups on its
ratcache entries is needed as an isolated operation.  This is
implemented as part of a different function within hugetlbpage.c that
ties it to inode and key lookup and allocation.

The following patch simply moves the code already present into its own
function, calls it, and makes it available for hugetlbfs to use.

On Wed, 30 Oct 2002, Aaron Lehmann wrote:
>
> Now running 'make oldconfig' or 'make menuconfig' requires a Qt
> installation. I believe that this is a bug because these still work
> fine without Qt when the -k flag is passed to make.

Yes, it's a bug. This fixes it without breaking xconfig.

into penguin.transmeta.com:/home/penguin/torvalds/repositories/kernel/linux

This means:
  1/ We don't need an order-4 allocation for each nfsd that starts
  2/ We don't need an order-4 allocation in skb_linearize when
     we receive a 32K write request
  3/ It will be easier to incorporate the zero-copy read changes

The pages are handed around using an xdr_buf (instead of svc_buf)
much like the NFS client so future crypto code can use the same
data structure for both client and server.

The code assumes that most requests and replies fit in a single page.
The exceptions are assumed to have some largish 'data' bit, and the
rest must fit in a single page.
The 'data' bits are file data, readdir data, and symlinks.
There must be only one 'data' bit per request.
This is all fine for nfs/nlm.

This isn't complete:
  1/ NFSv4 hasn't been converted yet (it won't compile)
  2/ NFSv3 allows symlinks upto 4096, but the code will only support
     upto about 3800 at the moment
  3/ readdir responses are limited to about 3800.

but I thought that patch was big enough, and the rest can come
later.


This patch introduces vfs_readv and vfs_writev as parallels to
vfs_read and vfs_write.  This means there is a fair bit of
duplication in read_write.c that should probably be tidied up...

nfsd_readdir - the common readdir code for all version of nfsd,
contains a number of version-specific things with appropriate checks,
and also does some xdr-encoding which rightly belongs elsewhere.

This patch simplifies nfsd_readdir to do just the core stuff, and moves
the version specifics into version specific files, and the xdr encoding
into xdr encoding files.

I forgot to add '1' for the record-length header in RPC/TCP.
 Thanks to  Hirokazu Takahashi <taka@valinux.co.jp>

Currently if the kmalloc in exports_open fails,
the seq_file isn't seq_released.

We now do the kmalloc first, and make sure to kfree
if seq_open fails.

The 'unexport everything' that happens when the
last nfsd thread dies was shuting down too much -
things that should only be shut down on module unload.

There is one remaining instance of CONFIG_MULTIQUAD in the kernel source.

Fix it to use the proper CONFIG_X86_NUMAQ instead.

Define an interface for interpreting and updating superblocks
so we can more easily define new formats.

With this patch, (almost) all superblock layout information is
locating in a small set of routines dedicated to superblock
handling.  This will allow us to provide a similar set for
a different format.

The two exceptions are:
 1/ autostart_array where the devices listed in the superblock
    are searched for.
 2/ raid5 'knows' the maximum number of devices for
     compute_parity.

These will be addressed in a later patch.

A few updates for x86-64 in 2.5.44. Some of the bugs fixed were serious.

- Don't count ACPI mappings in end_pfn. This shrinks mem_map a lot
  on many setups.
- Fix mem= option. Remove custom mapping support.
- Revert per_cpu implementation to the generic version. The optimized one
  that used %gs directly triggered too many toolkit problems and was an
  constant source of bugs.
- Make sure pgd_offset_k works correctly for vmalloc mappings. This makes
  modules work again properly.
- Export pci dma symbols
- Export other symbols to make more modules work
- Don't drop physical address bits >32bit on iommu free.
- Add more prototypes to fix warnings
- Resync pci subsystem with i386
- Fix pci dma kernel option parsing.
- Do PCI peer bus scanning after ACPI in case it missed some busses
  (that's a workaround - 2.5 ACPI seems to have some problems here that
  I need to investigate more closely)
- Remove the .eh_frame on linking. This saves several hundred KB in the
  bzImage
- Fix MTRR initialization. It works properly now on SMP again.
- Fix kernel option parsing, it was broken by section name changes in
  init.h
- A few other cleanups and fixes.
- Fix nonatomic warning in ioport.c

Add a `cold' hint to struct pagevec, and teach truncate and page
reclaim to use it.

Empirical testing showed that truncate's pages tend to be hot.  And page
reclaim's are certainly cold.

It is usually the case that pagecache reads use busmastering hardware
to transfer the data into pagecache.  This invalidates the CPU cache of
the pagecache pages.

So use cache-cold pages for pagecache reads.  To avoid wasting
cache-hot pages.

Hot/Cold pages and zone->lock amortisation

Patch from Martin Bligh.

Implements __free_pages_bulk().  Release multiple pages of a given
order into the buddy all within a single acquisition of the zone lock.

This also removes current->local_pages.  The per-task list of pages
which only ever contained one page.  To prevent other tasks from
stealing pages which this task has just freed up.

Given that we're freeing into the per-cpu caches, and that those are
multipage caches, and the cpu-stickiness of the scheduler, I think
current->local_pages is no longer needed.

This is the hot-n-cold-pages series.  It introduces a per-cpu lockless
LIFO pool in front of the page allocator.  For three reasons:

1: To reduce lock contention on the buddy lock: we allocate and free
   pages in, typically, 16-page chunks.

2: To return cache-warm pages to page allocation requests.

3: As infrastructure for a page reservation API which can be used to
   ensure that the GFP_ATOMIC radix-tree node and pte_chain allocations
   cannot fail.  That code is not complete, and does not absolutely
   require hot-n-cold pages.  It'll work OK though.

We add two queues per CPU.  The "hot" queue contains pages which the
freeing code thought were likely to be cache-hot.  By default, new
allocations are satisfied from this queue.

The "cold" queue contains pages which the freeing code expected to be
cache-cold.  The cold queue is mainly for lock amortisation, although
it is possible to explicitly allocate cold pages.  The readahead code
does that.

I have been hot and cold on these patches for quite some time - the
benefit is not great.

- 4% speedup in Randy Hron's benching of the autoconf regression
  tests on a 4-way.  Most of this came from savings in pte_alloc and
  pmd_alloc: the pagetable clearing code liked the warmer pages (some
  architectures still have the pgt_cache, and can perhaps do away with
  them).

- 1% to 2% speedup in kernel compiles on my 4-way and Martin's 32-way.

- 60% speedup in a little test program which writes 80 kbytes to a
  file and ftruncates it to zero again.  Ran four instances of that on
  4-way and it loved the cache warmth.

- 2.5% speedup in Specweb testing on 8-way

- The thing which won me over: an 11% increase in throughput of the
  SDET benchmark on an 8-way PIII:

	with hot & cold:

	RESULT for 8 users is 17971    +12.1%
	RESULT for 16 users is 17026   +12.0%
	RESULT for 32 users is 17009   +10.4%
	RESULT for 64 users is 16911   +10.3%

	without:

	RESULT for 8 users is 16038
	RESULT for 16 users is 15200
	RESULT for 32 users is 15406
	RESULT for 64 users is 15331

  SDET is a very old SPEC test which simulates a development
  environment with a large number of users.  Lots of users running a
  mix of shell commands, basically.


These patches were written by Martin Bligh and myself.

This one implements rmqueue_bulk() - a function for removing multiple
pages of a given order from the buddy lists.

This is for lock amortisation: take the highly-contended zone->lock
with less frequency, do more work once it has been acquired.

Convert global page state accounting to use per-cpu storage

(I think this code remains a little buggy, btw.  Note how I do

	per_cpu(page_states, cpu).member += (delta);

This gets done at interrupt time and hence is assuming that
the "+=" operation on a ulong is atomic wrt interrupts on
all architectures. How do we feel about that assumption?)

This is needed so that per-cpu information in the core kernel can be
accessed from modules.

Patch from Dipankar Sarma <dipankar@in.ibm.com>

This patch makes per_cpu bh_accounting safe for cpu_possible
allocation by using cpu notifiers.

Patch from Dipankar Sarma <dipankar@in.ibm.com>

This patch makes per_cpu tasklet vectors safe for cpu_possible
allocation by using CPU notifiers.

Patch from Dipankar Sarma <dipankar@in.ibm.com>

This patch changes the per-CPU data in timer management (tvec_bases)
to use per_cpu data area and makes it safe for cpu_possible allocation
by using CPU notifiers. End result - saving space.

Depends on cpu_possible patch.

Patch from Dipankar Sarma <dipankar@in.ibm.com>

This patch convers RCU per_cpu data to use per_cpu data area
and makes it safe for cpu_possible allocation by using CPU
notifiers.

A typical construct is:

	int cpu = get_cpu();

	foo = per_cpu(bar, cpu);
	put_cpu();

but this generates a compiler warning on uniprocessor builds: unused
variable `cpu'.

Add a dummy ref to `cpu' to per_cpu() to prevent this.

Convert balance_dirty_pages_ratelimited() to use percpu storage
for the ratelimiting counters.

- allocate memory for cpu buffers in cpu_up_prepare

- start the timer in cpu_online

- free the memory for cpu buffers in cpu_up_cancel.

From Manfred Spraul

- remove all typedef, except the kmem_bufctl_t.  It's a redefine for
  an int, i.e.  qualifies as tiny.

- convert most macros to inline functions.

Manfred added a new lock to protect the global list of slab caches.  We
already have a semaphore from those but he needs locking from timer
context.

So here we remove that lock and just do a down_trylock() on the
existing semaphore.  If that fails give up - we'll try again next timer
tick.

Manfred had all this weird code to schedule a kernel thread onto a
different CPU just so that we could bond a timer to that CPU.

Convert it all to use the new add_timer_on().