- 19 Jun, 2014 40 commits
-
-
Vladimir Kondratiev authored
Inform cfg80211 about Tx result Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Vladimir Kondratiev authored
Provide 2 files on the debugfs: - "rxon": write channel (1..4) to open Rx on it, 0 to rxoff - "tx_mgmt": write binary frame, starting from MAC header one need to care about turning receiver on/off before/after tx_mgmt Correct sequence is: echo $channel > rxon cat mfmt_frame > tx_mgmt echo 0 > rxon Signed-off-by:
-
Jahnavi Meher authored
Added code required for 40MHz. Signed-off-by:
Jahnavi Meher <jahnavi.meher@gmail.com> Signed-off-by:
-
Jahnavi Meher authored
Added support for host based bgscan. The h/w queues are blocked while bgscan is being performed and after coming to the connected channel, the queues are unblocked. Signed-off-by:
-
Jahnavi Meher authored
Adding support for 5GHz. Signed-off-by:
-
Jahnavi Meher authored
Send the QoS null packet via mgmt queue. Signed-off-by:
-
Jahnavi Meher authored
Added some debug messages. Signed-off-by:
-
Jahnavi Meher authored
The number of packets being dequeued from s/w queues was fixed - changed it to a dynamic calculation based on txop. There are also some fixes to the dequeuing algorithm. Signed-off-by:
-
Jahnavi Meher authored
Changed the SDIO interrupt variables and some clean ups. Signed-off-by:
-
Jahnavi Meher authored
Use SGI if configured while sending data packets at a fixed rate. Signed-off-by:
-
Jahnavi Meher authored
Lower level debug messages for some frames and changed confirm received for rsi_program_bb_rf() to a valid case. Signed-off-by:
-
Jahnavi Meher authored
Changed rate handling. Signed-off-by:
-
Jahnavi Meher authored
Made required changes to rsi_set_channel() and rsi_program_bb_rf() functions. Signed-off-by:
-
Jahnavi Meher authored
Changed the radio caps frame and added the required fields. Signed-off-by:
-
Jahnavi Meher authored
Added macros for the endpoints and set the default value of endpoint to 2.4GHz and 20MHz. Signed-off-by:
-
Jahnavi Meher authored
Filling in band from common->band. Signed-off-by:
-
Jahnavi Meher authored
Changed the function header to match the function name. Signed-off-by:
-
Jahnavi Meher authored
Changed the queue numbers to macros, and corrected the mappings. Signed-off-by:
-
Joe Perches authored
Use the zeroing function instead of dma_alloc_coherent & memset(,0,) Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Rajkumar Manoharan authored
Signed-off-by:
Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by:
-
Rajkumar Manoharan authored
Use seperate tx queue for each AC in each channel context and expose these information to mac80211 to avoid stopping one channel context leads to stopping the entire traffic for that AC even on other contexts. Signed-off-by:
-
Felix Fietkau authored
Configure the TSF based hardware timer for a channel switch. Also set up backup software timer, in case the gen timer fails. This could be caused by a hardware reset. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
TSF time might have been updated by the incoming beacon, need update the channel switch timer to reflect the change. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
In multi channel context (AP + STA case), adjust the TSF time of the AP chanctx to keep its beacons at half beacon interval offset relative to the STA chanctx. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Rajkumar Manoharan authored
Update current offchannel duration during scan or roc request. Signed-off-by:
-
Felix Fietkau authored
Add a basic state machine for switch channel context for beacon transmission. Signed-off-by:
-
Rajkumar Manoharan authored
Group and set hw state (opmode, primary_sta, beacon conf) per channel context instead of whole list of vifs. This would allow each channel context to run in different mode (STA/AP). Signed-off-by:
-
Rajkumar Manoharan authored
Signed-off-by:
-
Felix Fietkau authored
Save TSF in channel context for multiple operating channels. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Rajkumar Manoharan authored
Retrieve appropriate operating channel context while switching between operating and off channels. Signed-off-by:
-
Felix Fietkau authored
Add channel context operations (add, remove, change, assign and unassign) to enable support for multiple channels. Signed-off-by:
-
Felix Fietkau authored
Add remain on channel support in order to enable multi-channel concurrency. Signed-off-by:
-
