- 26 Apr, 2016 40 commits
-
-
Francesco Ruggeri authored
If macvlan_common_newlink fails in register_netdevice after macvlan_init then it decrements port->count twice, first in macvlan_uninit (from register_netdevice or rollback_registered) and then again in macvlan_common_newlink. A similar problem may exist in the ipvlan driver. This patch consolidates modifications to port->count into macvlan_init and macvlan_uninit (thanks to Eric Biederman for suggesting this approach). v3: remove macvtap specific bits. Signed-off-by:
Francesco Ruggeri <fruggeri@arista.com> Acked-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Manish Chopra says: ==================== qed: Bandwidth configuration support This series adds support in driver for min/max bandwidth configuration for the PF on the link change notification or on explicit request of bandwidth update from the MFW [management firmware]. The same infrastructure would later be used by user based flows [for example, rate shaping for the VFs] Please consider applying this series to "net-next" ==================== Signed-off-by: -
Manish Chopra authored
This patch adds support for PF minimum bandwidth update or configuration notified by management firmware. Signed-off-by:
Manish Chopra <manish.chopra@qlogic.com> Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
-
Manish Chopra authored
This patch adds support for PF maximum bandwidth update or configuration notified by management firmware. Signed-off-by:
-
Manish Chopra authored
This patch adds relevant APIs needed to configure WFQ (Weighted fair queueing) values for the vports. WFQ configuration is used per vport basis when minimum bandwidth update/configuration is notified to the PF by the management firmware. Signed-off-by:
-
David S. Miller authored
Hariprasad Shenai says: ==================== cxgb4: minor fixes, decode msgs and code refactor for few functions This patch series adds new routine to get adapter information and removes some redundant messages logged in dmesg. Fixes race while freeing tx descriptors. Decodes module type and link down reason codes obtained from firmware. Refactor port initialization and FW_PORT_CMD handling. Pass correct port id in DCB message handler to obtain netdev associated. This patch series has been created against net-next tree and includes patches on cxgb4 driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. ==================== Signed-off-by: -
Hariprasad Shenai authored
Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
The firmware can send a set of asynchronous replies through FW_PORT_CMD with DCBX information when that's negotiated with the Link Peer. The old code always assumed that a FW_PORT_CMD reply was always a Get Port Information message. This change conditionalizes the code to only handle the Get Port Information messages and throws a warning if we don't understand what we've been given. Also refactor t4_handle_fw_rpl() so that core functionality performed by t4_handle_get_port_info() for a specified port. Signed-off-by:
-
Hariprasad Shenai authored
Signed-off-by:
-
Hariprasad Shenai authored
Refactor t4_port_init() so that the core functionality is done by t4_init_portinfo() for a particular port. Also rename variables to sensible ones. Signed-off-by:
-
Hariprasad Shenai authored
Decode and log port module error, unknown modules and unsupported modules. Signed-off-by:
-
Hariprasad Shenai authored
There could be race between t4_eth_xmit() and t4_free_sge_resources() while freeing tx descriptors, take txq lock in t4_free_sge_resources(). We need to stop the xmit frame path which runs in bottom half context while unloading the driver using _bh variant of the lock. This is to prevent the deadlock between xmit and driver unload. Signed-off-by:
-
Hariprasad Shenai authored
Signed-off-by:
-
Hariprasad Shenai authored
Add new routine to print out general adapter information (various version numbers, adapter name, part number, serial number, etc.) and remove redundant information dumped in the Port Information. Signed-off-by:
-
David S. Miller authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2016-04-26 Here's another set of Bluetooth & 802.15.4 patches for the 4.7 kernel: - Cleanups & refactoring of ieee802154 & 6lowpan code - Security related additions to ieee802154 and mrf24j40 driver - Memory corruption fix to Bluetooth 6lowpan code - Race condition fix in vhci driver - Enhancements to the atusb 802.15.4 driver Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by:
-
David S. Miller authored
Nicolas Dichtel says: ==================== netlink: align attributes when needed (patchset #3) This is the continuation (series #3) of the work done to align netlink attributes when these attributes contain some 64-bit fields. It's the last patchset from what I've seen. The last user of nla_put_u64() is block/drbd. This module does not use standard netlink API (see all the stuff in include/linux/genl_magic_struct.h and include/linux/genl_magic_func.h). I didn't modify it because it's seems hard to do it whithout testing and fully understanding the context (for example, why include/linux/drbd_genl.h is not part of uapi?). Any thoughts? ==================== Signed-off-by: -
Nicolas Dichtel authored
Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Nicolas Dichtel authored
Signed-off-by:
-
Nicolas Dichtel authored
Signed-off-by:
-
Nicolas Dichtel authored
I also fix commit 8b32ab9e6ef1: use nla_total_size_64bit() for OVS_FLOW_ATTR_USED in ovs_flow_cmd_msg_size(). Fixes: 8b32ab9e6ef1 ("ovs: use nla_put_u64_64bit()") Signed-off-by: -
Nicolas Dichtel authored
I also fix the value of INET_DIAG_MAX. It's wrong since commit 8f840e47 which is only in net-next right now, thus I didn't make a separate patch. Fixes: 8f840e47 ("sctp: add the sctp_diag.c file") Signed-off-by:
-
Nicolas Dichtel authored
Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Nicolas Dichtel authored
Signed-off-by:
-
Nicolas Dichtel authored
Signed-off-by:
-
David S. Miller authored
Tom Herbert says: ==================== ila: Support for checksum neutral translations This patch set updates ILA to support draft-herbert-nvo3-ila-02. The primary addition is support checksum neutral ILA translation. This allows address to be performed and still keep any transport layer checksums that include the addresses in their pseudo header to still be correct without the translator needing to parse L4. Other items are: - Structures for ILA addresses, identifiers, locators - Disallow translation on non-ILA addresses (check by type in identifier). - Change xlat (nf_input) to translates solely based on matching locators not identifiers (since identifiers are not obfuscated by checksum neutral). - Side effect if above is that multiple ILA domains are supported. Each local locator can map to a different SIR address (ILA domain), and each domain defines its own identifier space. Tested: Ran TCP_RR with 200 cnxs. ILA performance is slightly better than previously since we are not longer parsing L4 for checksum handling. I amd seeing about 1% performance overhead. Also ran TCP_STREAM and tested non-ILA address (type=0) are not translated. v2: Fix compilation errors ==================== Signed-off-by: -
Tom Herbert authored
Support checksum neutral ILA as described in the ILA draft. The low order 16 bits of the identifier are used to contain the checksum adjustment value. The csum-mode parameter is added to described checksum processing. There are three values: - adjust transport checksum (previous behavior) - do checksum neutral mapping - do nothing On output the csum-mode in the ila_params is checked and acted on. If mode is checksum neutral mapping then to mapping and set C-bit. On input, C-bit is checked. If it is set checksum-netural mapping is done (regardless of csum-mode in ila params) and C-bit will be cleared. If it is not set then action in csum-mode is taken. Signed-off-by:
Tom Herbert <tom@herbertland.com> Signed-off-by:
-
Tom Herbert authored
Change model of xlat to be used only for input where lookup is done on the locator part of an address (comparing to locator_match as key in rhashtable). This is needed for checksum neutral translation which obfuscates the low order 16 bits of the identifier. It also permits hosts to be in muliple ILA domains (each locator can map to a different SIR address). A check is also added to disallow translating non-ILA addresses (check of type in identifier). Signed-off-by:
-
Tom Herbert authored
Add structures for identifiers, locators, and an ila address which is composed of a locator and identifier and in6_addr can be cast to it. This includes a three bit type field and enums for the types defined in ILA I-D. In ILA lwt don't allow user to set a translation for a non-ILA address (type of identifier is zero meaning it is an IID). This also requires that the destination prefix is at least 65 bytes (64 bit locator and first byte of identifier). Signed-off-by:
-
Julia Lawall authored
The first argument of pci_free_consistent has type struct pci_dev *, so use NULL instead of 0. The semantic patch that performs this transformation is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ @@ pci_free_consistent( - 0 + NULL , ...) // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
David S. Miller authored
Yisen Zhuang says: ==================== net: hns: add support of debug dsaf device There are two kinds of dsaf device in hns, one is for service ports, contains crossbar in it, can work under different mode. Another is for debug port, only can work under single port mode. The current code only declares a dsaf device for both service ports and debug ports.It is not so readability. This patch separates it to three platform devices to make the code more simple and readability. The diagram of all port in one platform device(old): CPU | | DSAF(one platform device) -------------------------------------------------------------- / | | | | | / | PPE PPE PPE | / | | | | | / | | | | | / | crossbar | | | / | | | | |/ | ----------------------------------- | | | | | | | | | | | | | | | | | | | | | | | | MAC MAC MAC MAC MAC MAC MAC MAC | | | | | | | | | | | -------------------------------------------------------------- | | | | | | | | PHY PHY PHY PHY PHY PHY PHY PHY The diagram of separating ports to three platform(new): CPU | ----------------------------------- | | | ---------------------------------------------- --------- --------- | | | | | | | | | PPE | | PPE | | PPE | | | | | | | | | | | | | | | | | | | | crossbar | | | | | | | | | | | | | | | | | ---------------------------------- | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MAC MAC MAC MAC MAC MAC | | MAC | | MAC | | | | | | | | | | | | | | | ---------------------------------------------- --------- --------- | | | | | | \ / | / | PHY PHY PHY PHY PHY PHY \ / PHY / PHY \ / / \ / / DSAF(three platform device) We take the compatibility into consideration, and it works well by using the old dts file(tested on d02 board). For more details, please see individual patches. ==================== Signed-off-by: -
Yisen.Zhuang\(Zhuangyuzeng\) authored
Because debug dsaf port was separated from service dsaf port, this patch updates the related configurations of hns dts, changes it to match with the new binding files. This also removes enet nodes which don't exist in d02 board. Signed-off-by:
Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by:
-
Yisen.Zhuang\(Zhuangyuzeng\) authored
This patch adds description for port-idx-in-ae attribute. Signed-off-by:
-
Yisen.Zhuang\(Zhuangyuzeng\) authored
Because debug dsaf port was separated from service dsaf port, this patch updates the related information of DT binding. Signed-off-by:
-
Yisen.Zhuang\(Zhuangyuzeng\) authored
Port mode offset for each dsaf port is different. The current code is not so readability. This patch adds configuration named port-mode-offset to make the code simple and more readability. If port-mode-offset isn't exists, default value 0 will be used. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
-
Yisen.Zhuang\(Zhuangyuzeng\) authored
The reset offset for each port in a dsaf is different. The current code is not so readability. This patch adds configuration named port-rst-offset to make the code simple and more readability. If this attribute doesn't exist, default value of this attribute is equal to its port index. Signed-off-by:
-
Yisen.Zhuang\(Zhuangyuzeng\) authored
This patch adds attribute cpld_ctrl for dsaf port node, parses the syscon for mac_cb from dts, and changes the method of access the cpld related registers through syscon. Signed-off-by:
-
Yisen.Zhuang\(Zhuangyuzeng\) authored
There are two kinds of dsaf device in hns, one is for service ports, contains crossbar in it, can work under different mode. Another is for debug port, only can work under "single-port" mode. The current code only declared a dsaf device for both service ports and debug ports. This patch separate it to three platform devices. Here is the diagram of all port in one platform device(old): CPU | | DSAF(one platform device) -------------------------------------------------------------- / | | | | | / | PPE PPE PPE | / | | | | | / | | | | | / | crossbar | | | / | | | | |/ | ----------------------------------- | | | | | | | | | | | | | | | | | | | | | | | | MAC MAC MAC MAC MAC MAC MAC MAC | | | | | | | | | | | -------------------------------------------------------------- | | | | | | | | PHY PHY PHY PHY PHY PHY PHY PHY Here is the diagram of separate all ports to three platform(new): CPU | ----------------------------------- | | | ---------------------------------------------- --------- --------- | | | | | | | | | PPE | | PPE | | PPE | | | | | | | | | | | | | | | | | | | | crossbar | | | | | | | | | | | | | | | | | ---------------------------------- | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MAC MAC MAC MAC MAC MAC | | MAC | | MAC | | | | | | | | | | | | | | | ---------------------------------------------- --------- --------- | | | | | | \ / | / | PHY PHY PHY PHY PHY PHY \ / PHY / PHY \ / / \ / / DSAF(three platform device) Signed-off-by: -
Daode Huang authored
This patch tunes the header file by the alphabetical order. Signed-off-by:
-
Yisen.Zhuang\(Zhuangyuzeng\) authored
This patch provides the read/write function for dsaf to access the registers through syscon methods. Signed-off-by:
-
Yisen.Zhuang\(Zhuangyuzeng\) authored
Add the subctrl reset offset for dsaf, this property is used to reset xge/ge ports for different dsaf. If this attribute is not present, default value 0 will be used. Signed-off-by:
-
