Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Prevent NUMONYX M29W128G memories from using write buffer,
because it doesn't work properly.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

In the existing implementation, ecc_stats fields are incremented only by
one, regardless of master mtd errors number. For example, if there are N
errors were corrected by ECC, partition ecc_stats.corrected will be
incremented by one.

This commit changes simple increment to sum of old value and parent mtd
error count.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch adds multi-chip support for the Micron MT29F8G08FAB NAND
flash memory on the TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch adds documentation for the new NAND FSL UPM bindings for:

 NAND: FSL-UPM: add multi chip support
 NAND: FSL-UPM: Add wait flags to support board/chip specific delays

It also documents the old binding for "chip-delay".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern. The TQM8548_BE requires a further short delay
after writing out a buffer. Normally the R/B pin should be checked, but
it's not connected on the TQM8548_BE. The existing driver uses similar
fixed delay points. To manage these extra delays in a more general way,
I introduced the "fsl,ump-wait-flags" property allowing the board-
specific driver to specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. This requires support for multiple GPIOs for the RNB pins.
The NAND chips are selected through address lines defined by the
FDT property "fsl,upm-addr-line-cs-offsets".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Move the driver model init code out of the "#ifdef CONFIG_PROC_FS"
block.

Tested with both values of CONFIG_PROC_FS .  Tested with CONFIG_MTD=m .

Issue was reported here: http://lkml.org/lkml/2009/4/4/107Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Follow-on patch to the previous driver model patch for the MTD
framework.  This one makes various MTD drivers connect to the
driver model tree, so /sys/devices/virtual/mtd/* nodes are no
longer present ... mostly drivers used on boards I have handy.

Based on a patch from Kay Sievers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

1) Add more sysfs attributes: flags, size, erasesize, writesize,
   oobsize, numeraseregions, name

2) Move core_initcall() code into init_mtd().  The original approach
   does not work if CONFIG_MTD=m .

3) Add device_unregister() in del_mtd_device() so that devices get
   removed from sysfs as each driver is unloaded.
Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Update driver model support in the MTD framework, so it fits
better into the current udev-based hotplug framework:

 - Each mtd_info now has a device node.  MTD drivers should set
   the dev.parent field to point to the physical device, before
   setting up partitions or otherwise declaring MTDs.

 - Those device nodes always map to /sys/class/mtdX device nodes,
   which no longer depend on MTD_CHARDEV.

 - Those mtdX sysfs nodes have a "starter set" of attributes;
   it's not yet sufficient to replace /proc/mtd.

 - Enabling MTD_CHARDEV provides /sys/class/mtdXro/ nodes and the
   /sys/class/mtd*/dev attributes (for udev, mdev, etc).

 - Include a MODULE_ALIAS_CHARDEV_MAJOR macro.  It'll work with
   udev creating the /dev/mtd* nodes, not just a static rootfs.

So the sysfs structure is pretty much what you'd expect, except
that readonly chardev nodes are a bit quirky.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

A pointer to plat_nand_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded.  Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.

An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Hamish Moffatt <hamish@cloud.net.au>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

A pointer to sa1100_mtd_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded.  Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.

An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Reported-by: Dan Carpenter <error27@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Now as all PXA Zaurii are converted to use the physmap map,
drop the sharpsl-flash map completely.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

SLOF has a further node which could not be evaluated
by the current routine. The current routine returns
because the node hasn't the required reg property. As
fix this patch adds a check to determine the partition
child nodes. If the node is not a partition the number
of total partitions will be decreased and loop continues
with the next nodes.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Jeremy Baker <Jeremy.Baker@renesas.com>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Fix a bad dependency in the Blackfin code on a RomFS config symbol that doesn't
exist upstream.
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Fix the configuration of the RomFS to make sure that at least one 
backing store method is always selected.  This is done by rendering it 
down to a choice item that selects between Block, MTD and both.

This also works correctly in the case that CONFIG_MTD=m: MTD cannot be 
selected as a backing store unless CONFIG_ROMFS_FS is also 'm'.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Change RomFS so that it can use MTD devices directly - without the intercession
of the block layer - as well as using block devices.

This permits RomFS:

 (1) to use the MTD direct mapping facility available under NOMMU conditions if
     the underlying device is directly accessible by the CPU (including XIP);

 (2) and thus to be used when the block layer is disabled.

RomFS can be configured with support just for MTD devices, just for Block
devices or for both.  If RomFS is configured for both, then it will treat
mtdblock device files as MTD backing stores, not block layer backing stores.

I tested this using a CONFIG_MMU=n CONFIG_BLOCK=n kernel running on my FRV
board with a RomFS image installed on the mtdram test device.  I see my test
program being run XIP:

	# cat /proc/maps
	...
	c0c000b0-c0c01f8c r-xs 00000000 1f:00 144        /mnt/doshm
	...

GDB on the kernel can be used to show that these addresses are within the
set-aside RAM space.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add support for direct mapping through mtdconcat, if possible, by attaching the
samebacking_dev_info structure to the master.

It has some restrictions:

 (1) It won't permit direct mapping of concatenated devices that have differing
     BDIs.

 (2) It doesn't support maps that span the 'gap' between devices, although it
     possibly could if the devices spanned across return compatible
     (ie. contiguous) addresses from their get_unmapped_area() ops.
Signed-off-by: Gavin Lambert <gavinl@compacsort.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Present backing device capabilities for MTD character device files to allow
NOMMU mmap to do direct mapping where possible.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

OneNAND write-while-program method of writing improves performance,
compared with ordinary writes, by transferring data to OneNAND's
RAM buffers atthe same time as programming the NAND core.

When writing several NAND pages at a time, an improvement of
12% to 25% is seen.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

panic_write may read in an interrupt context.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Currently redboot and afx parser return allocated mtd_partition array
and cmdlinepart and ar7 return persistent array.

This patch make cmdlinepart and ar7 also return allocated array, so
that all users can free it regardless of parser type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

- do not leave spin lock locked
- initialise spin lock
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

MTD's have both an index number and a name.  Formerly,
the MTD selected for mtdoops was done only by index
number.  With this patch, a name can be used instead.

For example, the kernel command line:

	console=ttyMTD5

selects MTD 5 for mtdoops.  But now this is also possible:

	console=ttyMTD,log

which selects the MTD named "log" for mtdoops.

This has the advantage that partitions can be added or
removed that would affect the MTD index number but not the
name, without having to then change the kernel command line.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The nftl module is missing the block-major-93-* alias that would cause
it to be auto-loaded when a nftl of that type is opened.  This patch
adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The mtdchar module is missing the char-major-90-* alias that would cause
it to be auto-loaded when a device of that type is opened.  This patch
adds the alia..
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

If the inval_cache_and_wait_for_operation() is re-entered by write operation when erase
operation is in progress, the chip->erase_suspended will be cleared, this cause the erase
timeo is not reset and will result time out error for erase.
Signed-off-by: Graff Yang <graff.yang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This is a map driver for NOR flash chips on RBTX4939 board.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Bächle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch adds support for the integrated NAND flash controller of the
TXx9 family.

Once upon a time there were tx4925ndfmc and tx4938ndfmc driver.  They
were removed due to bitrot in 2005.
This new driver is completely rewritten based on a driver in CELF patch
archive.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Bächle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>