When using NFC-F we should copy the NFCID2 buffer that we got from
SENSF_RES through the ATR_REQ NFCID3 buffer. Not doing so violates
NFC Forum digital requirement #189.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

LLCP validation requires TSN to be 0x03 for type F.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.

Transaction starts by emitting "Direct read" and acknowledged mode
bytes. Then packet length is read allowing to allocate correct NCI
socket buffer. After that payload is retrieved.

A delay after the transaction can be added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.

If acknowledged mode is set:
- CRC of header and payload is checked
- if frame reception fails (CRC error): NACK is sent
- if received frame has ACK or NACK flag: unblock nci_spi_send()

Payload is passed to NCI module.

At the end, driver interruption is re asserted.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.

The NCI over SPI header is added in front of NCI packet.
If acknowledged mode is set, CRC-16-CCITT is added to the packet.
Then the packet is forwarded to SPI module to be sent.

A delay after the transaction is added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.

After data has been sent, driver interruption is re-asserted.

If acknowledged mode is set, nci_spi_send will block until
acknowledgment is received.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The NFC Forum defines a transport interface based on
Serial Peripheral Interface (SPI) for the NFC Controller
Interface (NCI).

This module implements the SPI transport of NCI, calling SPI module
directly to read/write data to NFC controller (NFCC).

NFCC driver should provide functions performing device open and close.
It should also provide functions asserting/de-asserting interruption
to prevent TX/RX race conditions.
NFCC driver can also fix a delay between transactions if needed by
the hardware.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Exiting on the error case is more typical to the kernel coding style.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This is a simple forward to the HCI driver. When driver is done with the
operation, it shall directly notify NFC Core by calling
nfc_fw_upload_done().
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

As several NFC chipsets can have their firmwares upgraded and
reflashed, this patchset adds a new netlink command to trigger
that the driver loads or flashes a new firmware. This will allows
userspace triggered firmware upgrade through netlink.
The firmware name or hint is passed as a parameter, and the driver
will eventually fetch the firmware binary through the request_firmware
API.
The cmd can only be executed when the nfc dev is not in use. Actual
firmware loading/flashing is an asynchronous operation. Result of the
operation shall send a new event up to user space through the nfc dev
multicast socket. During operation, the nfc dev is not openable and
thus not usable.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

skb->dev is used for carrying a net_device pointer and not
an nci_dev pointer.

Remove usage of skb-dev to carry nci_dev and replace it by parameter
in nci_recv_frame(), nci_send_frame() and driver send() functions.

NfcWilink driver is also updated to use those functions.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Fix to return -ENOMEM in the nfc device alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

There is no builtin command for driver to check the presence of
Felica and Jewel device, it is more reasonable for the userspace
daemon neard to build seperate commands to check the presence of
the card.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFCID2 is defined as the first 2 manufacturer ID (IDm) bytes.
NFC DEP (NFC peer to peer) devices Type-F NFCID2 must start with
0x01fe according to the NFC Digital Specification.
By checking those first 2 bytes we send the right command either to the
reader gate when NFCID2 != 0x1fe (The NFC tag case) or to the NFCIP1 gate
when seeing an NFC DEP device (The NFC peer to peer case).

Without this fix, Felica (Type F) tags are not properly detected with this
driver.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Since raising/lowering the limits based on INI has
been changed, the error limit for OFDM has to be 1000,
not 3500.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With the new rate control API, the driver can now apply the
tx rate to outgoing frames just before they are uploaded to
the device. This is important because the rate control can
now react to fading or improving links a bit sooner.

Also, the driver no longer needs to sort the outgoing frames
for sample attempts (which affected the size of A-MPDUs and
the throughput of the link). For aggregated data frames, the
driver (and rate control) needs only to calculate and apply
a single set of tx rates to every subframe of the whole
aggregate.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix to return -ENOMEM in the skb alloc error handling case
instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support for Mediatek Bluetooth device

T:  Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0e8d ProdID=763f Rev= 1.00
S:  Manufacturer=MediaTek
S:  Product=BT
S:  SerialNumber=1.0
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=450mA
A:  FirstIf#= 0 IfCount= 2 Cls=ff(vend.) Sub=ff Prot=ff
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
Signed-off-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Conflicts:
	drivers/net/wireless/iwlwifi/mvm/mac80211.c

Added statistics for flow-control and packets dropped by the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently firmware requested credits do not require fifo credits.
From a buffer management point of view this is incorrect. So
firwmware requested credits require also fifo credits before the
packet can be transferred to the host.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts commit dd9c4640.

With "iwl{4965,3495): workaround for firmware frame tx rejection"
patches we can enable IEEE80211_HW_REPORTS_TX_ACK_STATUS again.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware can reject to transmit frame on passive channel, when it
did not yet received any frame with valid CRC on that channel.
Workaround this problem in the driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware can reject to transmit frame on passive channel, when it
did not yet received any frame with valid CRC on that channel.
Workaround this problem in the driver.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add functions that will stop/wake all queues. Make them safe
regarding multiple calls and when some ac are stopped/woke
independently.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch enabels ath5k to use the new rate table to lookup each
mrr rate and retry information per packet.
Signed-off-by: Benjamin Vahl <bvahl@net.t-labs.tu-berlin.de>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ah->noise is maintained globally and not per-channel. This
is updated in the reset() routine after the NF history has been
filled for the *current channel*, just before switching to
the new channel. There is no need to do it inside getnf(), since
ah->noise must contain a value for the new channel.

Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commits,

"ath9k: Fix regression in channelwidth switch at the same channel"
"ath9k: Fix invalid noisefloor reading due to channel update"

attempted to fix noisefloor calibration when a channel switch
happens due to HT20/HT40 bandwidth change. This is causing invalid
readings resulting in messages like:

"ath: phy16: NF[0] (-45) > MAX (-95), correcting to MAX".

This results in an incorrect noise being used initially for reporting
the signal level of received packets, until NF calibration is done
and the history buffer is updated via the ANI timer, which happens
much later.

When a bandwidth change happens, it is appropriate to reset
the internal history data for the channel. Do this correctly in the
reset() routine by checking the "chanmode" variable.

Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For AR9485 boards with XLNA, the default gpio config
is not set correctly, fix this.

Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

N-PHY and HT-PHY support is more or less stable and should be activated
by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Most users are using bcma with a PCIe card, activate support for
this by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When b43 gets build into the kernel and it should use bcma we have to
ensure that bcma was also build into the kernel and not as a module.
In this patch this is also done for SSB, although you can not
build b43 without ssb support for now.

This fixes a build problem reported by Randy Dunlap in
5187EB95.2060605@infradead.org
Reported-By: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All known ar7010+ar* device and current FW support STBC TX. This patch
make use of it and suggest to send STBC if peer support it.
I use wort "suggest" since currenly we have separate rate controller
in FW which will make decision based on rate and hardware.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

WMI PCP Start flow should not be handled through:
net_device_ops->ndo_open()->wil_up()->__wil_up()
because it missing mandatory FW parameters (SSID,Channel,IEs, Security...).

Prior to AP starting __wil_up() may be called with iftype set
cfg80211_ops->change_virtual_intf(NL80211_IFTYPE_AP or STATION)
depend on the application hostapd/wpa_supplicant/iw.
there should not be an attempt to start an AP flow,
AP/PCP start flow will be started latter by cfg80211_ops->start_ap().
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Tracing in wil6210 is activated with WIL6210_TRACING and not with
ATH6KL_TRACING, this is used for the ath6kl driver. Rename the config
option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

at the vring initialisation, memory pool get allocated in the FW.
Make it 1-st because FW need this memory pool to precess
next commands
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No more need for special processing of EAPOL, FW can now send EAPOL frames
using normal Tx queue for TID 0

This fixes "schedule while atomic" bug - start_xmit called in softirq context;
while WMI mechanism that was used may sleep.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When starting secure AP, in some cases wpa_s provides probe template but not
probe/assoc IE's. In this case, derive missing IE's from probe.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>