The loopback driver allows the user to set a minimum delay of up to one
second to be inserted between test iterations (i.e. request
submissions). The delay is currently specified in microseconds and is
implemented using udelay.

Busy looping for long periods is not just anti-social; udelay must not
be used for delays longer than a few milliseconds due to the risk of
integer overflow.

Replace the broken udelay with a usleep_range with a 100 us range for
short delays (< 20 ms) and otherwise revert to using msleep.

Fixes: b36f04fa ("greybus: loopback: Convert thread delay to microseconds")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org> # 4.9+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It fixes the following issue reported by checkpatch.pl:
Prefer kernel type 'u32' over 'uint32_t'
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver does not have a low-latency mode and should not report
anything else.

Also drop the skip-test flag which isn't used either.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the following errors:
Use 4 digit octal (0777) not decimal permissions
Signed-off-by: Abdul Rauf <abdulraufmujahid@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Found by checkpatch:
- s/cacluated/calculated/
- s/convertor/converter/
- s/psudo/pseudo/
- s/halfs/halves/
Signed-off-by: Joseph Wright <rjosephwright@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There are multiple entries for ili9225 display defined in
flexfb_chip_table array. remove duplicate entries and
keep single entry.
Signed-off-by: Amitesh Singh <singh.amitesh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Modify lirc_parallel driver to use the new parallel port device model.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Modify all the msg union fields from typedefs to
to proper structures.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: https://review.whamcloud.com/24566Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change lnet_hdr_t from typedef to proper structure.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: https://review.whamcloud.com/24566Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change lnet_magicversion_t from typedef to proper structure.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: https://review.whamcloud.com/24566Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change lnet_acceptor_connreq_t from typedef to proper structure.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: https://review.whamcloud.com/24566Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change lnet_process_id_packed_t from typedef to proper structure.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: https://review.whamcloud.com/24566Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change lnet_ni_status_t from typedef to proper structure.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: https://review.whamcloud.com/24566Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change lnet_ping_info_t from typedef to proper structure.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: https://review.whamcloud.com/24566Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change lnet_handle_wire_t from typedef to proper structure.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: https://review.whamcloud.com/24566Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change uint32_t to u32, solved the issue reported by checkpatch.pl:

CHECK: Prefer kernel type 'u32' over 'uint32_t'
+			uint32_t *format, uint32_t *rate, u8 *channels,

CHECK: Prefer kernel type 'u32' over 'uint32_t'
+			uint32_t format, uint32_t rate, u8 channels,
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Vaibhav Agarwal <vaibhav.sr@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed comparison, moved the constant to the right side of the test
Found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the checkpatch issue by adding space around '='.
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 76222772
"iio: accel: st_accel: handle deprecated bindings"
attempted to be smart and let users use the old I2C
driver and the new SPI driver, or the old SPI driver and
the new I2C driver in combination for the LIS3LV02,
and put the restrictions on the I2C and SPI subdrivers
not not be combined with the old subdrivers.

This doesn't work since the IIO ST accel top-level
component selects the I2C and SPI subdrivers, resulting
in the following Kconfig noise:

warning: (IIO_ST_ACCEL_3AXIS) selects IIO_ST_ACCEL_I2C_3AXIS
which has unmet direct dependencies (IIO && !SENSORS_LIS3_I2C
&& IIO_ST_ACCEL_3AXIS && IIO_ST_SENSORS_I2C)
warning: (IIO_ST_ACCEL_3AXIS) selects IIO_ST_ACCEL_SPI_3AXIS
which has unmet direct dependencies (IIO && !SENSORS_LIS3_SPI
&& IIO_ST_ACCEL_3AXIS && IIO_ST_SENSORS_SPI)
(...)

This fixes the issue by putting the dependencies directly
in the top-level component instead, so that it never gets
to select its unselectable subcomponent.

Fixes: 76222772 ("iio: accel: st_accel: handle deprecated bindings")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Jonathan writes:

Second round of IIO new device support, cleanups and features for the 4.11 cycle

New device support:
* lsm6dsx imu
  - new driver and bindings.
* max11100 adc
  - new driver and bindings.
* tlc4541
  - new driver
* tmp007 thermopile
  - new driver.

Core
* in kernel interfaces
  - pass through raw values if no scaling provided and a processed value is
    requested.
* trigger
  - close a race condition in acquiring trigger reference.
  - constify device_type structures.
  - rework the viio_trigger_alloc function to be much neater and easier to
  read.
  - free trigger resources correctly on some error paths. Avoids putting a
  module we don't have.

Documentation
* ABI
  - specify a unit for proximity measurements.

Cleanups and features
* ads1015
  - constify iio_info structure.
* ads7950 cleanups following merge in previous pull
  - Add device tree bindings
  - Drop the ti prefix from the module name in common with other drivers.
  - Change regulator name to vref to match datasheet and other drivers.
* ak8974
  - remove a redundant zero timeout check.
* bmi160
  - use variable names for sizeof instead of types.
* cm3605
  - mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
  - alignment fixes and newline improvements.
  - combine proxim_get and read_proxim for simpler code.
  - drop unused ISL29028_DEV_ATTR macro
  - move some error logging into functions to cut out repitition.
  - make error messages more consistent.
  - tidy up some brackets.
  - drop the enable flag that nothing uses.
  - only set proximity rate and ALS scale when relevant channel type is enabled.
  - runtime pm support.
* lsm6dsx
  - fix wrong values for gyro sensitivitiy.
* mag3110
  - claim direct mode during sysfs reads to avoid a race condition.
* max1363
  - export OF device table IDs as module aliases.
* max30100
  - use msleep for long uncritical delays.
* mcp4531
  - export OF device table as module aliases.
* ms5611
  - claim direct mode during sysfs reads to avoid a race condition.
* opt3001
  - export OF device table as module aliases.
* sx9500
  - claim direct mode during oversampling changes to avoid a race condition.

These stand-alone trigger drivers were using iio_trigger_put()
where they should have been using iio_trigger_free().  The
iio_trigger_put() adds a module_put which is bad since they
never did a module_get.

In the sysfs driver, module_get/put's are used as triggers are
added & removed. This extra module_put() occurs on an error path
in the probe routine (probably rare).

In the bfin-timer & interrupt trigger drivers, the module resources
are not explicitly managed, so it's doing a put on something that
was never get'd.  It occurs on the probe error path and on the
remove path (not so rare).

Tested with the sysfs trigger driver.
The bfin & interrupt drivers were build tested & inspected only.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

1) Reverse the test for kmalloc() failure so we can pull everything
   back one tab.
2) Use gotos for unwinding.
3) Some of the extra line breaks for the 80 character limit are no
   longer needed so we can remove them.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Declare iio_info structures as const as they are only stored in
the info field of a iio_dev structure. This field is of type const,
so iio_info structures having similar properties can be made const too.

File size before:
   text	   data	    bss	    dec	    hex	filename
   6944	    792	      0	   7736	   1e38	drivers/iio/adc/ti-ads1015.o

File size after:
   text   data	    bss	    dec	    hex	filename
   7264	    472	      0	   7736	   1e38	drivers/iio/adc/ti-ads1015.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Declare device_type structure as const as it is only stored in the
type field of a device structure. This field is of type const, so add
const to declaration of device_type structure.

File size before:
   text	   data	    bss	    dec	    hex	filename
   5389	    208	     48	   5645	   160d	iio/industrialio-trigger.o

File size after:
   text	   data	    bss	    dec	    hex	filename
   5453	    176	     48	   5677	   162d	iio/industrialio-trigger.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

In iio_trigger_write_current() we find the trigger we want while
holding mutex on the list of triggers, but we don't actually do a
get on it while holding mutex.  We wait until further validations
are completed and we're sure it's the one we want.  Race condition
is that it could be freed by the time we do the get.

Solution is to grab the trigger (iio_trigger_get) as soon as we
find it while holding mutex on the list of triggers.  If later
we decide it's not the right one, put it back. (iio_trigger_put).
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds runtime power management support to the isl29028 driver.
It defaults to powering off the device after two seconds of inactivity.

isl29028_chip_init_and_power_on() currently only zeros the CONFIGURE
register on the chip, which will cause the chip to turn off. This patch
also renames that function to isl29028_clear_configure_reg() since it is
now used in several places.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

isl29028_chip_init_and_power_on() calls isl29028_set_als_scale() and
this is not needed until the user actually needs to take a reading from
the ALS/IR sensor. This patch moves the isl29028_set_als_scale() call
from isl29028_chip_init_and_power_on() to isl29028_set_als_ir_mode().
This sets the stage for faster resume times from runtime power
management if the user is only querying the proximity sensor.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

isl29028_chip_init_and_power_on() calls isl29028_set_proxim_sampling()
and this is not needed until the user actually needs to take a proximity
reading. This patch moves the isl29028_set_proxim_sampling() call from
isl29028_chip_init_and_power_on() to isl29028_enable_proximity().
This sets the stage for faster resume times from the runtime power
management if the user is only querying the ALS/IR sensor.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

isl29028_enable_proximity() has a boolean argument named enable. This
function is only called once and the enable flag is set to true in that
call. This patch removes the enable parameter from that function.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

isl29028_write_raw() contains unnecessary parenthesis when checking to
see if the passed in lux scale is valid. This patch removes the
unnecessary parenthesis.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

If the call to devm_iio_device_alloc() fails, then isl29028_probe()
logs a message saying that memory cannot be allocated. The user's system
most likely has larger issues at this point. This patch removes that
error message since the error code is passed on and the message is not
necessary.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

If the call to isl29028_chip_init_and_power_on() in isl29028_probe()
fails, then isl29028_probe() will log an error message. All of the
error paths in that call path already have error logging in place. This
patch removes the unnecessary logging.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The wording and style of the different error messages was not
consistent. This patch makes the wording and style consistent
throughout the driver.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

When isl29028_set_als_scale() fails, it was up to both callers to log
the failure message. This patch moves the logging into
isl29028_set_als_scale() to reduce the overall amount of code in the
driver.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

When isl29028_set_proxim_sampling() fails, it was up to both callers to
log the failure message. This patch moves the logging into
isl29028_set_proxim_sampling() to reduce the overall amount of code in
the driver.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The #define ISL29028_DEV_ATTR was not used so this patch removes the
unnecessary code.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add and remove newlines to improve code readability in preparation for
moving the driver out of staging.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The alignment of the variables in the struct isl29028_chip is not
consistent. This changes all of the variables to use consistent
alignment to improve the code readability.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

isl29028_proxim_get() checks to see if the promixity needs to be
enabled on the chip and then calls isl29028_read_proxim(). There
are no other callers of isl29028_read_proxim(). The naming between
these two functions can be confusing so this patch combines the
two to avoid the confusion.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>