Add basic support for Broadcom serial slave devices.
Probe the serial device, retrieve its maximum speed and
register a new hci uart device.

Tested/compatible with bcm43438 (RPi3).
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The commands that read the basic vendor information about the Broadcom
controller are duplicated for UART and USB devices. Combine them into a
single function to reduce the code complexity.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Not all Broadcom controller support the 4Mbps operational speed on UART
devices. This is because the UART clock setting changes might not be
supported.

  < HCI Command: Broadcom Write UART Clock Setting (0x3f|0x0045) plen 1
         01                                               .
  > HCI Event: Command Complete (0x0e) plen 4
       Broadcom Write UART Clock Setting (0x3f|0x0045) ncmd 1
         Status: Unknown HCI Command (0x01)

To support any operational speed higher than 3Mbps, support for this
command is required. With that respect it is better to not enforce any
operational speed by default. Only when its support is known, then allow
for higher operational speed.

This patch assigns the 4Mbps opertional speed only for devices
discovered through ACPI and leave all others at the default 115200.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

BT-Controller connected as platform non-root-hub device and
usb-driver initialize such device with wakeup disabled,
Ref. usb_new_device().

At present wakeup-capability get enabled by hid-input device from usb
function driver(e.g. BT HID device) at runtime. Again some functional
driver does not set usb-wakeup capability(e.g LE HID device implement
as HID-over-GATT), and can't wakeup the host on USB.

Most of the device operation (such as mass storage) initiated from host
(except HID) and USB wakeup aligned with host resume procedure. For BT
device, usb-wakeup capability need to enable form btusc driver as a
generic solution for multiple profile use case and required for USB remote
wakeup (in-bus wakeup) while host is suspended. Also usb-wakeup feature
need to enable/disable with HCI interface up and down.
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The GPD Pocket is shipping with a BCM2045 USB HCI with its vendor and
product information set to 0000:0000 and also has its interface class
set to 255 (Vendor Specific Class). Luckily it does advertise usable
manufacturer and product strings.

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM2045A0
S:  SerialNumber=AC83F30677CB
C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Reported-by: Christopher Williamson <home@chrisaw.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

While the kfree of dhkey_a is of the same address of tmp, it
probably is clearer and more human readable if tmp is kfree'd
rather than dhkey_a.

Detected by CoverityScan, CID#1448650 ("Free of address-of expression")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Kernel config options should include useful help text; I had to look
up the terms on wikipedia.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3494 Rev= 2.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Currently the activity LED is solid on during continuous activity.
Blink the LED during continuous activity to match Windows driver
behavior.

Cards with activity LED:
power LED = solid on when up, off when down
activity LED = blinking during activity, off when idle

Cards without activity LED:
power LED = solid on when up, off when down, blinking during activity
(don't have such a card so I don't know if Windows driver does the same
thing)
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Keep power LED on during activity.

LED timer races with power LED disabling in hci_close(), resulting in
power LED left on after closing.
Stop LED timer before disabling power LED.

BTW. On cards without an activity LED, the behavior is a bit weird:
The LED is on after hci_open() but only until the first data transfer.
Then it's off in idle and on during activity.
It could be improved by keeping the LED on in idle and flashing during
activity.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Anycom CF-300 (HP C8249A) has both power and activity LEDs.
However the id read in bluecard_open() is 0x73 so the driver does not
enable the LEDs.
Remove the CARD_HAS_PCCARD_ID check to enable LEDs.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Xin Long says:

====================
sctp: remove typedefs from structures part 5

As we know, typedef is suggested not to use in kernel, even checkpatch.pl
also gives warnings about it. Now sctp is using it for many structures.

All this kind of typedef's using should be removed. This patchset is the
part 5 to remove all typedefs in include/net/sctp/constants.h.

Just as the part 1-4, No any code's logic would be changed in these patches,
only cleaning up.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_subtype_t, and
replace with union sctp_subtype in the places where it's
using this typedef.

Note that it doesn't fix many indents although it should,
as sctp_disposition_t's removal would mess them up again.
So better to fix them when removing sctp_disposition_t in
later patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_event_t, and
replace with enum sctp_event in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_event_timeout_t, and
replace with enum sctp_event_timeout in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_event_other_t, and
replace with enum sctp_event_other in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_event_primitive_t, and
replace with enum sctp_event_primitive in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_state_t, and
replace with enum sctp_state in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_ierror_t, and
replace with enum sctp_ierror in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_xmit_t, and
replace with enum sctp_xmit in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_sock_state_t, and
replace with enum sctp_sock_state in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_transport_cmd_t, and
replace with enum sctp_transport_cmd in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_scope_t, and
replace with enum sctp_scope in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_scope_policy_t and keep
it's members as an anonymous enum.

It is also to define SCTP_SCOPE_POLICY_MAX to replace the num 3
in sysctl.c to make codes clear.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_retransmit_reason_t, and
replace with enum sctp_retransmit_reason in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove the typedef sctp_lower_cwnd_t, and
replace with enum sctp_lower_cwnd in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before the GMAC on the Anarion chip can be used, the PHY interface
selection must be configured with the DWMAC block in reset.

This layer covers a block containing only two registers. Although it
is possible to model this as a reset controller and use the "resets"
property of stmmac, it's much more intuitive to include this in the
glue layer instead.

At this time only RGMII is supported, because it is the only mode
which has been validated hardware-wise.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With new transparent VF support, it is possible to get a deadlock
when some of the deferred work is running and the unregister_vf
is trying to cancel the work element. The solution is to use
trylock and reschedule (similar to bonding and team device).
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Fixes: 0c195567 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During testing with a background iperf pushing 1Gbit/sec worth of
traffic and having both ifconfig and ethtool collect statistics, we
could see quite frequent deadlocks. Convert the often accessed DSA slave
network devices statistics to per-cpu 64-bit statistics to remove these
deadlocks and provide fast efficient statistics updates.

Fixes: f613ed66 ("net: dsa: Add support for 64-bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
tcp cwnd undo refactor

This patch series consolidate similar cwnd undo functions
implemented by various congestion control by using existing
tcp socket state variable. The first patch fixes a corner
case in of cwnd undo in Reno and HTCP. Since the bug has
existed for many years and is very minor, we consider this
patch set more suitable for net-next as the major change
is the refactor itself.

- v1->v2
  Fix trivial compile errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Most TCP congestion controls are using identical logic to undo
cwnd except BBR. This patch consolidates these similar functions
to the one used currently by Reno and others.
Suggested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using ssthresh to revert cwnd is less reliable when ssthresh is
bounded to 2 packets. This patch uses an existing variable in TCP
"prior_cwnd" that snapshots the cwnd right before entering fast
recovery and RTO recovery in Reno.  This fixes the issue discussed
in netdev thread: "A buggy behavior for Linux TCP Reno and HTCP"
https://www.spinics.net/lists/netdev/msg444955.htmlSuggested-by: Neal Cardwell <ncardwell@google.com>
Reported-by: Wei Sun <unlcsewsun@gmail.com>
Signed-off-by: Yuchung Cheng <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using Broadcom Systemport device in 32bit Platform, ifconfig can
only report up to 4G tx,rx status, which will be wrapped to 0 when the
number of incoming or outgoing packets exceeds 4G, only taking
around 2 hours in busy network environment (such as streaming).
Therefore, it makes hard for network diagnostic tool to get reliable
statistical result, so the patch is used to add 64bit support for
Broadcom Systemport device in 32bit Platform.

This patch provides 64bit statistics capability on both ethtool and ifconfig.
Signed-off-by: Jianming.qiao <kiki-good@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moving PF module param console_bitmask to lio_main.c for consistency.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's supposed to be a one-to-one correspondence between the 18 macros
that #define the OCT_DEV states (in octeon_device.h) and the strings in the
oct_dev_state_str array, but there are only 14 strings in the array.

Add the missing strings (so they become 18 in total), and also revise some
incorrect/outdated text of existing strings.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
phylink and sfp support

This patch series introduces generic support for SFP sockets found on
various Marvell based platforms.  The idea here is to provide common
SFP socket support which can be re-used by network drivers as
appropriate, rather than each network driver having to re-implement
SFP socket support.

SFP sockets typically use other system resources, eg, I2C buses to read
identifying information, and GPIOs to monitor socket state and control
the socket.  Meanwhile, some network drivers drive multiple ethernet
ports from one instantiation of the driver.

It is not desirable to block the initialisation of a network driver
(thus denying other ports from being operational) if the resources
for the SFP socket are not yet available.  This means that an element
of independence between the SFP support code and the driver is
required.

More than that, SFP modules effectively bring hotplug PHYs to
networking - SFP copper modules normally contain a standard PHY
accessed over the I2C bus, and it is desirable to read their state
so network drivers can be appropriately configured.

To add to the complexity, SFP modules can be connected in at least
two places:

1. Directly to the serdes output of a MAC with no intervening PHY.
   For example:

     mvneta ----> SFP socket

2. To a PHY, for example:

     mvpp2 ---> PHY ---> copper
                 |
                 `-----> SFP socket

This code supports both setups, although it's not fully implemented
with scenario (2).

Moreover, the link presented by the SFP module can be one of the
10Gbase-R family (for SFP+ sockets), SGMII or 1000base-X (for SFP
sockets) depending on the module, and network drivers need to
reconfigure themselves accordingly for the link to come up.

For example, if the MAC is configured for SGMII and a fibre module
is plugged in, the link won't come up until the MAC is reconfigured
for 1000base-X mode.

The SFP code manages the SFP socket - detecting the module, reading
the identifying information, and managing the control and status
signals.  Importantly, it disables the SFP module transmitter when
the MAC is down, so that the laser is turned off (but that is not
a guarantee.)

phylink provides the mechanisms necessary to manage the link modes,
based on the SFP module type, and supports hot-plugging of the PHY
without needing the MAC driver to be brought up and down on
transitions.  phylink also supports the classical static PHY and
fixed-link modes.

I currently (but not included in this series) have code to convert
mvneta to use phylink, and the out of tree mvpp2x driver.  I have
nothing for the mvpp2 driver at present as that driver is only
recently becoming functional on 10G hardware, and is missing a lot
of features that are necessary to make things work correctly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for SFP hotpluggable modules via sfp-bus and phylink.
This supports both copper and optical SFP modules, which require
different Serdes modes in order to properly negotiate the link.

Optical SFP modules typically require the Serdes link to be talking
1000BaseX mode - this is the gigabit ethernet mode defined by the
802.3 standard.

Copper SFP modules typically integrate a PHY in the module to convert
from Serdes to copper, and the PHY will be configured by the vendor
to either present a 1000BaseX Serdes link (for fixed 1000BaseT) or a
SGMII Serdes link.  However, this is vendor defined, so we instead
detect the PHY, switch the link to SGMII mode, and use traditional
PHY based negotiation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add in-band autonegotation support for 10GBase-KR mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for reading and writing the clause 45 MII registers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>