- 18 Feb, 2014 3 commits
-
-
Roger Quadros authored
During resume don't touch SUSPENDM/RESUME bits of POWER register while restoring controller context. These bits might be changed by the controller during resume operation and so will be different than what they were during suspend. e.g. SUSPENDM bit is set by software during USB global suspend but automatically cleared by the controller during remote wakeup or during resume. Setting this bit back while restoring context causes undesired behaviour. i.e. Babble interrupt is generated and USB is broken. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
-
Ajay Kumar Gupta authored
Disables PING on status phase of control transfer. PING token is not mandatory in status phase of control transfer and so some high speed USB devices don't support it. If such devices are connected to MUSB then they would not respond to PING token causing delayed or failed enumeration. [Roger Q] Fixes enumeration issues with some Super-Speed USB hubs e.g. Dlink DUB-1340 Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
-
Felipe Balbi authored
phy_power_off() can, depending on the PHY being used, start I2C transactions which shouldn't happen in atomic context. Current call to phy_power_off() inside omap2430_runtime callbacks causes the following dump, as a fix, just don't power off the PHY in runtime. [ 18.606414] [<c037eac0>] (__schedule+0x5c/0x50c) from [<c037d3bc>] (schedule_timeout+0x1f4/0x25c) [ 18.623809] [<c037d3bc>] (schedule_timeout+0x1f4/0x25c) from [<c037f12c>] (wait_for_common+0xc8/0x1ac) [ 18.649291] [<c037f12c>] (wait_for_common+0xc8/0x1ac) from [<c028c1c0>] (omap_i2c_xfer+0x338/0x488) [ 18.674499] [<c028c1c0>] (omap_i2c_xfer+0x338/0x488) from [<c0288144>] (__i2c_transfer+0x40/0x74) [ 18.692047] [<c0288144>] (__i2c_transfer+0x40/0x74) from [<c0288a2c>] (i2c_transfer+0x6c/0x90) [ 18.709320] [<c0288a2c>] (i2c_transfer+0x6c/0x90) from [<c02351c8>] (regmap_i2c_read+0x48/0x68) [ 18.726715] [<c02351c8>] (regmap_i2c_read+0x48/0x68) from [<c023161c>] (_regmap_raw_read+0x128/0x220) [ 18.752685] [<c023161c>] (_regmap_raw_read+0x128/0x220) from [<c02317b4>] (regmap_raw_read+0xa0/0x130) [ 18.779052] [<c02317b4>] (regmap_raw_read+0xa0/0x130) from [<c023193c>] (regmap_bulk_read+0xf8/0x16c) [ 18.805694] [<c023193c>] (regmap_bulk_read+0xf8/0x16c) from [<c0238ea8>] (twl_i2c_read+0xa4/0xe0) [ 18.823730] [<c0238ea8>] (twl_i2c_read+0xa4/0xe0) from [<c0274d34>] (__twl4030_phy_power.isra.12+0x1c/0x58) [ 18.850921] [<c0274d34>] (__twl4030_phy_power.isra.12+0x1c/0x58) from [<c0274df0>] (twl4030_phy_power.part.14+0x80/0xc8) [ 18.879699] [<c0274df0>] (twl4030_phy_power.part.14+0x80/0xc8) from [<c0274f9c>] (twl4030_set_suspend+0x54/0x1e8) [ 18.908325] [<c0274f9c>] (twl4030_set_suspend+0x54/0x1e8) from [<c027c8c4>] (omap2430_runtime_resume+0x5c/0x64) [ 18.937042] [<c027c8c4>] (omap2430_runtime_resume+0x5c/0x64) from [<c0225dd0>] (pm_generic_runtime_resume+0x2c/0x38) [ 18.966461] [<c0225dd0>] (pm_generic_runtime_resume+0x2c/0x38) from [<c0229fe0>] (__rpm_callback+0x54/0x80) [ 18.995117] [<c0229fe0>] (__rpm_callback+0x54/0x80) from [<c022a04c>] (rpm_callback+0x40/0x74) [ 19.013610] [<c022a04c>] (rpm_callback+0x40/0x74) from [<c022b3c8>] (rpm_resume+0x448/0x63c) [ 19.031921] [<c022b3c8>] (rpm_resume+0x448/0x63c) from [<c022b2e4>] (rpm_resume+0x364/0x63c) [ 19.050140] [<c022b2e4>] (rpm_resume+0x364/0x63c) from [<c022b874>] (__pm_runtime_resume+0x48/0x74) [ 19.077728] [<c022b874>] (__pm_runtime_resume+0x48/0x74) from [<c027b4fc>] (musb_gadget_pullup+0x1c/0xb4) [ 19.105895] [<c027b4fc>] (musb_gadget_pullup+0x1c/0xb4) from [<bf025c14>] (usb_function_deactivate+0x54/0xa4 [libcomposite]) [ 19.135955] [<bf025c14>] (usb_function_deactivate+0x54/0xa4 [libcomposite]) from [<bf05b3b8>] (obex_bind+0x124/0x1d8 [usb_f_obex]) [ 19.166870] [<bf05b3b8>] (obex_bind+0x124/0x1d8 [usb_f_obex]) from [<bf025794>] (usb_add_function+0x58/0xf4 [libcomposite]) [ 19.197143] [<bf025794>] (usb_add_function+0x58/0xf4 [libcomposite]) from [<bf037420>] (nokia_bind_config+0x204/0x250 [g_nokia]) [ 19.227905] [<bf037420>] (nokia_bind_config+0x204/0x250 [g_nokia]) from [<bf0263fc>] (usb_add_config+0x28/0xc0 [libcomposite]) [ 19.258483] [<bf0263fc>] (usb_add_config+0x28/0xc0 [libcomposite]) from [<bf03709c>] (nokia_bind+0x9c/0x21c [g_nokia]) [ 19.288421] [<bf03709c>] (nokia_bind+0x9c/0x21c [g_nokia]) from [<bf0275bc>] (composite_bind+0x74/0x180 [libcomposite]) [ 19.318420] [<bf0275bc>] (composite_bind+0x74/0x180 [libcomposite]) from [<c027d658>] (udc_bind_to_driver+0x2c/0xc4) [ 19.348114] [<c027d658>] (udc_bind_to_driver+0x2c/0xc4) from [<c027d764>] (usb_gadget_probe_driver+0x74/0x94) [ 19.377166] [<c027d764>] (usb_gadget_probe_driver+0x74/0x94) from [<c00086f8>] (do_one_initcall+0x94/0x138) [ 19.406005] [<c00086f8>] (do_one_initcall+0x94/0x138) from [<c007a460>] (load_module+0x113c/0x13c4) [ 19.434051] [<c007a460>] (load_module+0x113c/0x13c4) from [<c007a7b4>] (SyS_init_module+0xcc/0xec) [ 19.462127] [<c007a7b4>] (SyS_init_module+0xcc/0xec) from [<c000dd40>] (ret_fast_syscall+0x0/0x30) [ 19.490753] Code: 0a00002e e1a00004 eb001438 e598300c (e5d3202c) [ 19.506805] ---[ end trace 060b62ec0d68a78b ]--- [ 19.523132] Kernel panic - not syncing: Fatal exception in interrupt dump is from 3.12-rc5 kernel Reported-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
-
- 11 Feb, 2014 2 commits
-
-
Raymond Wanyoike authored
Interface #5 of 19d2:1270 is a net interface which has been submitted to the qmi_wwan driver so consequently remove it from the option driver. Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
Merge tag 'for-usb-linus-2014-02-11' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus Sarah writes: xhci: Revert TD fragment hacks. Hi Greg, Recently, we found that commit "35773dac "usb: xhci: Link TRB must not occur within a USB payload burst" causes a userspace regression. It will cause larger transfers submitted through usbfs that would have succeeded on older kernels to be rejected. Commit 35773dac was designed to address an issue where an ASIX USB ethernet device would get wedged when it was connected to a 1.0 xHCI host. Only this particular ethernet device was impacted, because only the ax88179_178a driver implemented scatter-gather in 3.12. The xHCI driver doesn't currently support TD fragment rules, and commit 35773dac was a quick hack that partially implemented one of the rules. This is the third regression this patch has caused. There's yet another quick hack to work around the issue, but I really want to support TD fragments properly, rather than hacking around it. It will take us a kernel release or two to get it implemented, since it is a big architectural change. This patchset backs out commit 35773dac, and the two bug fix patches for it. The first patch limits arbitrarily aligned scatter-gather under xHCI 1.0 hosts. As a result of this patchset: 1. usb-storage and uas will still be able to use scatter-gather, since they submit max packet sized aligned transfers. 2. usbfs will behave exactly as before, no more userspace regressions. 3. The ax88179_178a driver works fine without scatter-gather (Mark Lord confirms this). Users of the ASIX chipset may still see occasional packet loss on 1.0 xHCI hosts, if the xHCI driver needs to split a TRB across 64-KB boundaries, and a link TRB happens to fall between those two TRBs. I expect this corner case to be infrequent. Sarah Sharp
-
- 07 Feb, 2014 5 commits
-
-
Sarah Sharp authored
This reverts commit 35773dac. It's a hack that caused regressions in the usb-storage and userspace USB drivers that use usbfs and libusb. Commit 70cabb7d992f "xhci 1.0: Limit arbitrarily-aligned scatter gather." should fix the issues seen with the ax88179_178a driver on xHCI 1.0 hosts, without causing regressions. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@vger.kernel.org # 3.12
-
Sarah Sharp authored
This reverts commit d6c9ea90. We are ripping out commit 35773dac "usb: xhci: Link TRB must not occur within a USB payload burst" because it's a hack that caused regressions in the usb-storage and userspace USB drivers that use usbfs and libusb. This commit attempted to fix the issues with that patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@vger.kernel.org # 3.12
-
Sarah Sharp authored
This reverts commit f2d9b991. We are ripping out commit 35773dac "usb: xhci: Link TRB must not occur within a USB payload burst" because it's a hack that caused regressions in the usb-storage and userspace USB drivers that use usbfs and libusb. This commit attempted to fix the issues with that patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@vger.kernel.org #3.12
-
Sarah Sharp authored
xHCI 1.0 hosts have a set of requirements on how to align transfer buffers on the endpoint rings called "TD fragment" rules. When the ax88179_178a driver added support for scatter gather in 3.12, with commit 804fad45411b48233b48003e33a78f290d227c8 "USBNET: ax88179_178a: enable tso if usb host supports sg dma", it broke the device under xHCI 1.0 hosts. Under certain network loads, the device would see an unexpected short packet from the host, which would cause the device to stop sending ethernet packets, even through USB packets would still be sent. Commit 35773dac "usb: xhci: Link TRB must not occur within a USB payload burst" attempted to fix this. It was a quick hack to partially implement the TD fragment rules. However, it caused regressions in the usb-storage layer and userspace USB drivers using libusb. The patches to attempt to fix this are too far reaching into the USB core, and we really need to implement the TD fragment rules correctly in the xHCI driver, instead of continuing to wallpaper over the issues. Disable arbitrarily-aligned scatter-gather in the xHCI driver for 1.0 hosts. Only the ax88179_178a driver checks the no_sg_constraint flag, so don't set it for 1.0 hosts. This should not impact usb-storage or usbfs behavior, since they pass down max packet sized aligned sg-list entries (512 for USB 2.0 and 1024 for USB 3.0). Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Mark Lord <mlord@pobox.com> Cc: David Laight <David.Laight@ACULAB.COM> Cc: Bjørn Mork <bjorn@mork.no> Cc: Freddy Xin <freddy@asix.com.tw> Cc: Ming Lei <ming.lei@canonical.com> Cc: stable@vger.kernel.org # 3.12
-
Jan Moskyto Matejka authored
Commit afe2dab4 ("USB: add hex/bcd detection to usb modalias generation") changed the routine that generates alias ranges. Before that change, only digits 0-9 were supported; the commit tried to fix the case when the range includes higher values than 0x9. Unfortunately, the commit didn't fix the case when the range includes both 0x9 and 0xA, meaning that the final range must look like [x-9A-y] where x <= 0x9 and y >= 0xA -- instead the [x-9A-x] range was produced. Modprobe doesn't complain as it sees no difference between no-match and bad-pattern results of fnmatch(). Fixing this simple bug to fix the aliases. Also changing the hardcoded beginning of the range to uppercase as all the other letters are also uppercase in the device version numbers. Fortunately, this affects only the dvb-usb-dib0700 module, AFAIK. Signed-off-by: Jan Moskyto Matejka <mq@suse.cz> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 05 Feb, 2014 3 commits
-
-
Christian Engelmayer authored
Fix a memory leak in the usb_store_new_id() error paths. When bailing out due to sanity checks, the function left the already allocated usb_dynid struct in place. This regression was introduced by the following commits: c63fe8f6 (usb: core: add sanity checks when using bInterfaceClass with new_id) 1b9fb31f (usb: core: check for valid id_table when using the RefId feature) 52a6966c (usb: core: bail out if user gives an unknown RefId when using new_id) Detected by Coverity: CID 1162604. Signed-off-by: Christian Engelmayer <cengelma@gmx.at> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ulrich Hahn authored
Adding two more IDs to the ftdi_sio usb serial driver. It now connects Tagsys RFID readers. There might be more IDs out there for other Tagsys models. Signed-off-by: Ulrich Hahn <uhahn@eanco.de> Cc: Johan Hovold <johan@hovold.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Bjørn Mork authored
This device was mentioned in an OpenWRT forum. Seems to have a "standard" Sierra Wireless ifnumber to function layout: 0: qcdm 2: nmea 3: modem 8: qmi 9: storage Cc: <stable@vger.kernel.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 04 Feb, 2014 10 commits
-
-
Alan Stern authored
People sometimes create their own custom-configured kernels and forget to enable CONFIG_SCSI_MULTI_LUN. This causes problems when they plug in a USB storage device (such as a card reader) with more than one LUN. Fortunately, we can tell fairly easily when a storage device claims to have more than one LUN. When that happens, this patch asks the SCSI layer to probe all the LUNs automatically, regardless of the config setting. The patch also updates the Kconfig help text for usb-storage, explaining that CONFIG_SCSI_MULTI_LUN may be necessary. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Thomas Raschbacher <lordvan@lordvan.com> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> CC: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kristóf Ralovich authored
Add support for ANT USB-m Stick from Dynastream Innovations, by listing USB pid [34366.944805] usb 6-1: New USB device found, idVendor=0fcf, idProduct=1009 [34366.944817] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [34366.944824] usb 6-1: Product: ANT USB-m Stick [34366.944831] usb 6-1: Manufacturer: Dynastream Innovations Device reported (https://code.google.com/p/antpm/issues/detail?id=5) to work through: $ modprobe usbserial vendor=0x0fcf product=0x1009 Signed-off-by: Kristóf Ralovich <kristof.ralovich@gmail.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alan Stern authored
This patch adds an unusual-devs entry for the BlackBerry 9000. This fixes Bugzilla #22442. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Moritz Moeller-Herrmann <moritz-kernel@moeller-herrmann.de> Tested-by: Moritz Moeller-Herrmann <moritz-kernel@moeller-herrmann.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alan Stern authored
The Cypress ATACB unusual-devs entry for the Super Top SATA bridge causes problems. Although it was originally reported only for bcdDevice = 0x160, its range was much larger. This resulted in a bug report for bcdDevice 0x220, so the range was capped at 0x219. Now Milan reports errors with bcdDevice 0x150. Therefore this patch restricts the range to just 0x160. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Milan Svoboda <milan.svoboda@centrum.cz> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Josh Boyer authored
the PHY layer is supposed to be optional, considering some PHY have no control bus for SW to poke around. After commit 1ae5799e (usb: hcd: Initialize USB phy if needed) any HCD which didn't provide a PHY driver would emit annoying error messages. In this patch we're decreasing those messages to debugging only and we also add a PHY prefix or use dev_dbg so we know where they're coming from. Reported-by: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Bjørn Mork authored
Cc: stable <stable@vger.kernel.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Paul Zimmerman authored
The move from the staging tree to the main tree exposed a longstanding memory corruption bug in the dwc2 driver. The reordering of the driver initialization caused the dwc2 driver to corrupt the initialization data of the sdhci driver on the Raspberry Pi platform, which made the bug show up. The error is in calling to_usb_device(hsotg->dev), since ->dev is not a member of struct usb_device. The easiest fix is to just remove the offending code, since it is not really needed. Thanks to Stephen Warren for tracking down the cause of this. Reported-by: Andre Heider <a.heider@gmail.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Paul Zimmerman authored
Commit beb7e592 "staging: dwc2: add check on dwc2_core_reset return" broke the B -> A role switching on OTG-enabled platforms. This commit fixes it. Reported-by: Dinh Nguyen <dinguyen@altera.com> Tested-by: Dinh Nguyen <dinguyen@altera.com> Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Andre Heider authored
Add usb_disabled() check to prevent kernel oops when booting with "nousb" in the cmdline: Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... PC is at bus_add_device+0xe0/0x18c LR is at device_add_groups+0x1c/0x20 ... [<c02191c0>] (bus_add_device) from [<c0217130>] (device_add+0x41c/0x538) [<c0217130>] (device_add) from [<c023b1d4>] (usb_new_device+0x270/0x35c) [<c023b1d4>] (usb_new_device) from [<c0241174>] (usb_add_hcd+0x4fc/0x760) [<c0241174>] (usb_add_hcd) from [<c0254ce0>] (dwc2_hcd_init+0x434/0x510) [<c0254ce0>] (dwc2_hcd_init) from [<c02594f4>] (dwc2_driver_probe+0x130/0x170) [<c02594f4>] (dwc2_driver_probe) from [<c021bbd0>] (platform_drv_probe+0x28/0x58) Signed-off-by: Andre Heider <a.heider@gmail.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
Merge tag 'for-usb-linus-2014-02-04' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus Sarah writes: xhci: Fix some regressions introduced in 3.14. Hi Greg, Here's four patches for 3.14. One of them adds an xHCI host quirk, and the other three of them fix regressions introduced in 3.14. One regression causes USB 3.0 Link PM to be enabled on all xHCI hosts (even those that may not support it), which causes some USB 3.0 devices to not enumerate. A second regression causes some xHCI hosts that don't support 64-bit addressing to stop responding to commands and die. Note, these patches don't fix the recent usbfs regression that was caused by commit 35773dac "usb: xhci: Link TRB must not occur within a USB payload burst". I'm waiting for those patches to be tested. Please pull usb-linus into usb-next, as I have feature patches that rely on 140e3026 Revert "usbcore: set lpm_capable field for LPM capable root hubs" Sarah Sharp
-
- 03 Feb, 2014 4 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linuxLinus Torvalds authored
Pull parisc updates from Helge Deller: "The three major changes in this patchset is a implementation for flexible userspace memory maps, cache-flushing fixes (again), and a long-discussed ABI change to make EWOULDBLOCK the same value as EAGAIN. parisc has been the only platform where we had EWOULDBLOCK != EAGAIN to keep HP-UX compatibility. Since we will probably never implement full HP-UX support, we prefer to drop this compatibility to make it easier for us with Linux userspace programs which mostly never checked for both values. We don't expect major fall-outs because of this change, and if we face some, we will simply rebuild the necessary applications in the debian archives" * 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc: add flexible mmap memory layout support parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc parisc: convert uapi/asm/stat.h to use native types only parisc: wire up sched_setattr and sched_getattr parisc: fix cache-flushing parisc/sti_console: prefer Linux fonts over built-in ROM fonts
-
Mikulas Patocka authored
HPFS needs to load 4 consecutive 512-byte sectors when accessing the directory nodes or bitmaps. We can't switch to 2048-byte block size because files are allocated in the units of 512-byte sectors. Previously, the driver would allocate a 2048-byte area using kmalloc, copy the data from four buffers to this area and eventually copy them back if they were modified. In the current implementation of the buffer cache, buffers are allocated in the pagecache. That means that 4 consecutive 512-byte buffers are stored in consecutive areas in the kernel address space. So, we don't need to allocate extra memory and copy the content of the buffers there. This patch optimizes the code to avoid copying the buffers. It checks if the four buffers are stored in contiguous memory - if they are not, it falls back to allocating a 2048-byte area and copying data there. Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Mikulas Patocka authored
Previously, hpfs scanned all bitmaps each time the user asked for free space using statfs. This patch changes it so that hpfs scans the bitmaps only once, remembes the free space and on next invocation of statfs it returns the value instantly. New versions of wine are hammering on the statfs syscall very heavily, making some games unplayable when they're stored on hpfs, with load times in minutes. This should be backported to the stable kernels because it fixes user-visible problem (excessive level load times in wine). Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
- 02 Feb, 2014 12 commits
-
-
Helge Deller authored
Add support for the flexible mmap memory layout (as described in http://lwn.net/Articles/91829). This is especially very interesting on parisc since we currently only support 32bit userspace (even with a 64bit Linux kernel). Signed-off-by: Helge Deller <deller@gmx.de>
-
Guy Martin authored
On Linux, only parisc uses a different value for EWOULDBLOCK which causes a lot of troubles for applications not checking for both values. Since the hpux compat is long dead, make EWOULDBLOCK behave the same as all other architectures. Signed-off-by: Guy Martin <gmsoft@tuxicoman.be> Signed-off-by: Helge Deller <deller@gmx.de>
-
Helge Deller authored
The stat.h header file is exported to userspace. Some userspace applications failed to compile due to missing/unknown types, so we better convert it to use native types only (like it's done on other architectures too). Signed-off-by: Helge Deller <deller@gmx.de>
-
Helge Deller authored
Signed-off-by: Helge Deller <deller@gmx.de>
-
Helge Deller authored
This commit: f8dae006: parisc: Ensure full cache coherency for kmap/kunmap caused negative caching side-effects, e.g. hanging processes with expect and too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems. This patch now partly reverts it and has been in production use on our debian buildd makeservers since a week without any major problems. Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # v3.9+ Signed-off-by: Helge Deller <deller@gmx.de>
-
Helge Deller authored
The built-in ROM fonts lack many necessary ASCII characters, which is why it makes sens to prefer the Linux fonts instead if they are available. This makes consoles on STI graphics cards which are not supported by the stifb driver (e.g. Visualize FXe) looks much nicer. Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org # v3.13
-
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/stagingLinus Torvalds authored
Pull hwmon kconfig fixes from Jean Delvare. * 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: hwmon: Fix SENSORS_TMP102 dependencies to eliminate build errors hwmon: Fix SENSORS_LM75 dependencies to eliminate build errors
-
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linuxLinus Torvalds authored
Pull SLAB changes from Pekka Enberg: "Random bug fixes that have accumulated in my inbox over the past few months" * 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux: mm: Fix warning on make htmldocs caused by slab.c mm: slub: work around unneeded lockdep warning mm: sl[uo]b: fix misleading comments slub: Fix possible format string bug. slub: use lockdep_assert_held slub: Fix calculation of cpu slabs slab.h: remove duplicate kmalloc declaration and fix kernel-doc warnings
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linuxLinus Torvalds authored
Pull turbostat updates from Len Brown. * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: tools/power turbostat: introduce -s to dump counters tools/power turbostat: remove unused command line option turbostat: Add option to report joules consumed per sample turbostat: run on HSX turbostat: Add a .gitignore to ignore the compiled turbostat binary turbostat: Clean up error handling; disambiguate error messages; use err and errx turbostat: Factor out common function to open file and exit on failure turbostat: Add a helper to parse a single int out of a file turbostat: Check return value of fscanf turbostat: Use GCC's CPUID functions to support PIC turbostat: Don't attempt to printf an off_t with %zx turbostat: Don't put unprocessed uapi headers in the include path
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM SoC fixes from Olof Johansson: "Here's a set of patches for (hopefully) -rc1. Some of them are fixes, but a good number of them also do things such as enable new drivers in the defconfigs for platforms that have such devices, increases coverage of the multiplatform defconfig and some DTS changes that plumbs up some of the devices that now have bindings and driver support. The commit dates are recent; we've mostly collected these fixes in the last few days but I also had to rebuild the branch yesterday to sort out some internal conflicts which reset the timestamps. The changes should have been tested by each platform maintainer already (and few of them have cross-platform impact) so I'm personally not too concerned by it at this time" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits) ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA ARM: multi_v7_defconfig: add mvebu drivers clocksource: kona: Add basic use of external clock drivers: bus: fix CCI driver kcalloc call parameters swap ARM: dts: bcm28155-ap: Fix Card Detection GPIO ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers ARM: dts: zynq: Add SDHCI nodes ARM: hisi: don't select SMP ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS ARM: multi_v7: copy most options from tegra_defconfig ARM: iop32x: fix power off handling for the EM7210 board ARM: integrator: restore static map on the CP ARM: msm_defconfig: Enable MSM clock drivers ARM: dts: msm: Add clock controller nodes and hook into uart ARM: OMAP4+: move errata initialization to omap4_pm_init_early ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP) ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference ...
-
Jean Delvare authored
Similar to what was done for the lm75 driver. Add depends on THERMAL since that is what provides the register/unregister functions above, but only if THERMAL_OF was selected as this is an optional feature of the driver. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Randy Dunlap <rdunlap@infradead.org> Acked-by: Eduardo Valentin <eduardo.valentin@ti.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
-
Jean Delvare authored
Based on an earlier attempt by Randy Dunlap. Fix SENSORS_LM75 dependencies to eliminate build errors: drivers/built-in.o: In function `lm75_remove': lm75.c:(.text+0x12bd8c): undefined reference to `thermal_zone_of_sensor_unregister' drivers/built-in.o: In function `lm75_probe': lm75.c:(.text+0x12c123): undefined reference to `thermal_zone_of_sensor_register' Add depends on THERMAL since that is what provides the register/unregister functions above, but only if THERMAL_OF was selected as this is an optional feature of the driver. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Randy Dunlap <rdunlap@infradead.org> Acked-by: Eduardo Valentin <eduardo.valentin@ti.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
-
- 01 Feb, 2014 1 commit
-
-
Andy Shevchenko authored
The new option allows just run turbostat and get dump of counter values. It's useful when we have something more than one program to test. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
-