- 10 Aug, 2010 40 commits
-
-
Alessio Igor Bogani authored
Signed-off-by:
Alessio Igor Bogani <abogani@texware.it> Cc: stable <stable@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
dranch@trinnet.net authored
This patch is to add a US Interface, Inc. "Navigator" USB device. Specifically, it's a HAM Radio USB sound modem that also incorporates three pairs of unique FTDI serial ports. The standard Linux FTDI serial driver will only recognize the first two serial ports of an unknown FDTI derived device and this patch adds in recognition to these specific new IDs. Signed-off-by:
David A. Ranch <dranch@trinnet.net> Cc: stable <stable@kernel.org> Signed-off-by:
-
Alan Stern authored
This patch (as1410) makes a slight change to the strategy used for choosing a default configuration. Currently we skip configs whose first interface is RNDIS, if the kernel wasn't built with the corresponding driver. This risks losing access to the other interfaces in those configs. In addition, if there is only one config then we will end up not configuring the device at all. This changes the logic; now such configurations will be skipped only if there is at least one other config. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Tested-by:
Adam Kropelin <akropel1@rochester.rr.com> Signed-off-by:
-
Andrew Bird authored
This patch adds the product IDs of Huawei's K3765 and K4505 mobile broadband usb modems to option.c. It also adds a quirk to the option probe function so that binding to the device's network interface(class 0xff) is avoided. This is necessary to allow another driver to bind to that, and to avoid programs like wvdial opening a nonfunctioning tty during modem discovery. Signed-off-by:
Andrew Bird <ajb@spheresystems.co.uk> Cc: stable <stable@kernel.org> Signed-off-by:
-
Michal Nazarewicz authored
Moved the serial parameter handling code out of "#ifdef CONFIG_USB_FILE_STORAGE_TEST". This modifies Yann Cantin's commit "USB: Add a serial number parameter to g_file_storage" module as per Alan Stern's request. Signed-off-by:
Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
Anand Gadiyar <gadiyar@ti.com> Cc: David Brownell <david-b@pacbell.net> Cc: Yann Cantin <yann.cantin@laposte.net>
-
Kulikov Vasiliy authored
imx21_hc_reset() uses schedule_timeout() without setting state to STATE_(UN)INTERRUPTIBLE. As it is called in cycle without checking of pending signals, use schedule_timeout_uninterruptible(). Signed-off-by:
Kulikov Vasiliy <segooon@gmail.com> Signed-off-by:
-
John G. Rogers authored
I have added the ProductID=0xe729 VendorID=FTDI_VID=0x0403 which will enable support for the Segway Robotic Mobility Platform (RMP200) in the ftdi_sio kernel module. Currently, users of the Segway RMP200 must use a RUN+="/sbin/modprobe -q ftdi-sio product=0xe729 vendor=0x0403 in a udev rule to get the ftdi_sio module to handle the usb interface and mount it on /dev/ttyXXX. This is not a good solution because some users will have multiple USB to Serial converters which will use the ftdi_sio module. Signed-off-by:
John Rogers <jgrogers@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by:
-
Marek Szyprowski authored
This patch adds support for clock gating of the HS/OTG block. On S5PV210 otg gating clock is initally disabled so the driver needs to get and enable it before it can access its registers. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Marek Szyprowski authored
S5PV210 SoCs has 2 USB PHY interfaces, both enabled by writing zero to S3C_PHYPWR register. HS/OTG driver uses only PHY0, so do not touch bits related to PHY1. Signed-off-by:
-
Marek Szyprowski authored
drivers/usb/gadget/s3c-hsotg.c: In function ‘s3c_hsotg_otgreset’: drivers/usb/gadget/s3c-hsotg.c:2816: error: ‘MHZ’ undeclared (first use in this function) drivers/usb/gadget/s3c-hsotg.c:2816: error: (Each undeclared identifier is reported only once drivers/usb/gadget/s3c-hsotg.c:2816: error: for each function it appears in.) Signed-off-by:
-
Maurus Cuelenaere authored
The PLL that drives the USB clock supports 3 input clocks: 12, 24 and 48Mhz. This patch adds support to the USB driver for setting the correct register bit according to the given clock. This depends on the following patch: [PATCH] ARM: S3C64XX: Add USB external clock definition Signed-off-by:
Maurus Cuelenaere <mcuelenaere@gmail.com> Signed-off-by:
Ben Dooks <ben-linux@fluff.org> Signed-off-by:
-
Ben Dooks authored
If there is more data in the request than we could fit into a single hardware request, then check when the OutDone event is received if we have more data, and if so, schedule the new data instead of trying to complete the request (and in the case of EP0, sending a 0 packet in the middle of a transfer). Also, move the debug message about the current transfer state before the warning about a bad transfer. Signed-off-by:
-
Ben Dooks authored
The EP0 out limit is the same as the IN limit, so make them the same. Signed-off-by:
-
Ben Dooks authored
The maximum length for any EP0 IN request on EP0 is 127 bytes, not 128 as the driver currently has it. Signed-off-by:
-
Ben Dooks authored
Before trying a new setup transaction after getting an EP0 in complete interrupt, check that the driver did not try and send more EP0 IN data before enqueing a new setup transaction. This fixes a bug where we cannot send all of the IN data in one go so split the transfer, but then fail to send all the data as we start waiting for a new OUT transaction Signed-off-by:
-
Ben Dooks authored
Limit the IN FIFO write to a single packet per attempt at writing, as per the specifications and ensure that we don't return fifo-full so that we can continue writing packets if we have the space. Signed-off-by:
-
Ben Dooks authored
Add support for the dedicated FIFO mode on newer SoCs such as the S5PV210 partly to improve support and to fix the bug where any non-EP0 IN endpoint requires its own FIFO allocation. To fix this, we ensure that any non-zero IN endpoint is given a TXFIFO using the same allocation method as the periodic case (all our current hardware has enough FIFOs and FIFO memory for a 1:1 mapping) and ensure that the necessary transmission done interrupt is enabled. The default settings from reset for the core point all EPs at FIFO0, used for the control endpoint. However, the controller documentation states that all IN endpoints _must_ have a unique FIFO to avoid any contention during transmission. Note, this leaves us with a large IN FIFO for EP0 (which re-uses the old NPTXFIFO) for an endpoint which cannot shift more than a pair of packets at a time... this is a waste, but it looks like we cannot re-allocate space to the individual IN FIFOs as they are already maxed out (to be confirmed). Signed-off-by:
-
Ben Dooks authored
The USB documentation suggest that the FIFOs should be reset when a bus reset event happens. Use the s3c_hsotg_init_fifo() to ensure that the FIFO layout is correct and that the FIFOs are flushed before acknowledging the reset. Signed-off-by:
-
Ben Dooks authored
In shared fifo mode (used on older SoCs) the periodic in fifo beahves much more like a packet buffer, discarding old data when writing new data. Avoid this by ensuring that we do not load new transactions in when there is data sitting already in the FIFO. Note, this may not be an observed bug, we are fixing the case that this may happen. Signed-off-by:
-
Ben Dooks authored
Fix a problem where we have been underestimating the space available in the IN PTX/NPTX FIFOs by assuming that they where simply word aligned instead of in number-of-words. This means all length calculations need to be multiplied-by-4. Note, we do not change the information about fifo size or start addresses available to userspace as we assume the user can multiply by four easily and is already knows these values are in words. Signed-off-by:
-
Ben Dooks authored
Up the FIFO size for the TX to 1024 entries, as this now seems to work with all the cores. This fixes a problem when using large packets on a core with MPS set to 512 can hang due to insufficient space for the writes. The hang arises due to getting the non-periodic FIFO empty IRQ but not being able to satisfy any requests since there is never enough space to write 512 bytes into the buffer. This means we end up with a stream of interrupt requests. It is easier to up the TX FIFO to fill the space we left for it than to try and fix the positions in the code where we should have limited the max-packet size to < TXFIFOSIZE, since the TXFIFOSIZE depends on how the TX FIFOs have been setup. Signed-off-by:
-
Kulikov Vasiliy authored
If kzalloc() fails exit with -ENOMEM. Signed-off-by:
-
Andy Shevchenko authored
MS Windows mounts removable storage in "Removal optimized mode" by default. All the writes to the media are synchronous which is achieved by setting FUA (Force Unit Access) bit in SCSI WRITE(10,12) commands. This prevents I/O requests aggregation in block layer dramatically decreasing performance. This patch brings an option to accept or ignore mentioned bit a) via specifying module parameter "nofua", or b) through sysfs entry /sys/devices/platform/_UDC_/gadget/gadget-lunX/nofua (_UDC_ is the name of the USB Device Controller driver) Patch is based on the work that was done by Denis Karpov for Maemo 5 platform. Signed-off-by:
Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Acked-by:
-
Andy Shevchenko authored
Bring a strict way to get the 'ro' parameter from the user. The patch followed by this one adds another boolean parameter. To be consistent Michał Nazarewicz proposed to use simple_strtol() in both cases (correspondend discussion in LKML [1]). Due to simple_strtol() doesn't return error in a good way and we have a boolean parameter the strict_strtoul() is used. [1] http://lkml.org/lkml/2010/7/14/169Signed-off-by:
-
Andiry Xu authored
Enable isochronous urb enqueue. Signed-off-by:
Andiry Xu <andiry.xu@amd.com> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
Andiry Xu authored
Isochronous endpoint needs a bigger size of transfer ring. Isochronous URB consists of multiple packets, each packet needs a isoc td to carry, and there will be multiple trbs inserted to the ring at one time. One segment is too small for isochronous endpoints, and it will result in room_on_ring() check failure and the URB is failed to enqueue. Allocate bigger ring for isochronous endpoint. 8 segments should be enough. This will be replaced with dynamic ring expansion in the future. Signed-off-by:
-
Andiry Xu authored
This patch implements isochronous urb enqueue and interrupt handler part. When an isochronous urb is passed to xHCI driver, first check the transfer ring to guarantee there is enough room for the whole urb. Then update the start_frame and interval field of the urb. Always assume URB_ISO_ASAP is set, and never use urb->start_frame as input. The number of isoc TDs is equal to urb->number_of_packets. One isoc TD is consumed every Interval. Each isoc TD consists of an Isoch TRB chained to zero or more Normal TRBs. Call prepare_transfer for each TD to do initialization; then calculate the number of TRBs needed for each TD. If the data required by an isoc TD is physically contiguous (not crosses a page boundary), then only one isoc TRB is needed; otherwise one or more additional normal TRB shall be chained to the isoc TRB by the host. Set TRB_IOC to the last TRB of each isoc TD. Do not ring endpoint doorbell to start xHC procession until all the TDs are inserted to the endpoint transer ring. In irq handler, update urb status and actual_length, increase urb_priv->td_cnt. When all the TDs are completed(td_cnt is equal to urb_priv->length), giveback the urb to usbcore. Signed-off-by:
-
Andiry Xu authored
Add urb_priv data structure to xHCI driver. This structure allows multiple xhci TDs to be linked to one urb, which is essential for isochronous transfer. For non-isochronous urb, only one TD is needed for one urb; for isochronous urb, the TD number for the urb is equal to urb->number_of_packets. The length field of urb_priv indicates the number of TDs in the urb. The td_cnt field indicates the number of TDs already processed by xHC. When td_cnt matches length, the urb can be given back to usbcore. When an urb is dequeued or cancelled, add all the unprocessed TDs to the endpoint's cancelled_td_list. When process a cancelled TD, increase td_cnt field. When td_cnt equals urb_priv->length, giveback the cancelled urb. Signed-off-by:
-
Andiry Xu authored
This patch adds mechanism to process Missed Service Error Event. Sometimes the xHC is unable to process the isoc TDs in time, it will generate Missed Service Error Event. In this case some TDs on the ring are not processed and missed. When encounter a Missed Servce Error Event, set the skip flag of the ep, and process the missed TDs until reach the next processed TD, then clear the skip flag. Signed-off-by:
-
Andiry Xu authored
This patch adds new cases to trb_comp_code switch, and moves the switch judgment ahead of fetching td. Signed-off-by:
-
Andiry Xu authored
Remove redundant print messages in the interrupt context. Signed-off-by:
-
Andiry Xu authored
This patch moves the bulk and interrupt td processing part in handle_tx_event() into a separate function process_bulk_intr_td(). Signed-off-by:
-
Andiry Xu authored
This patch moves the ctrl td processing part in handle_tx_event() into a separate function process_ctrl_td(). Signed-off-by:
-
Andiry Xu authored
This patch moves the td universal processing part in handle_tx_event() into a separate function finish_td(). if finish_td() returns 1, it indicates the urb can be given back. Signed-off-by:
-
Pavel Kazlou authored
The patch adds Huawei ETS 1220 product id into the list of supported devices in 'option' usb serial driver. Signed-off-by:
Pavel Kazlou <p.i.kazlou@gmail.com> Signed-off-by:
-
Phil Dibowitz authored
The Logitech Harmony 700 series needs an extra delay during initialization. This patch adds a USB quirk which enables such a delay and adds the device to the quirks list. Signed-off-by:
Phil Dibowitz <phil@ipom.com> Cc: stable <stable@kernel.org> Signed-off-by:
-
Steven Robertson authored
Enlarging the buffer size via the MON_IOCT_RING_SIZE ioctl causes general protection faults. It appears the culprit is an incorrect argument to mon_free_buff: instead of passing the size of the current buffer being freed, the size of the new buffer is passed. Use the correct size argument to mon_free_buff when changing the size of the buffer. Signed-off-by:
Steven Robertson <steven@strobe.cc> Acked-by:
Pete Zaitcev <zaitcev@redhat.com> Cc: stable <stable@kernel.org> Signed-off-by:
-
Michal Nazarewicz authored
Removed entry referencing g_eth_ffs.c file from Makefile. The file never existed and the line was a leftover from a developing process. Signed-off-by:
Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by:
-
Alan Stern authored
This patch (as1409) removes some dead code from the ehci-hcd scheduler. Thanks to the previous patch in this series, stream->depth is no longer used. And stream->start and stream->rescheduled apparently have not been used for quite a while, except in some statistics-reporting code that never gets invoked. Signed-off-by:
-
Alan Stern authored
This patch (as1408) rearranges the scheduling code in ehci-hcd, partly to improve its structure, but mainly to change the way it works. Whether or not a transfer exceeds the hardware schedule length will now be determined by looking at the last frame the transfer would use, instead of the first available frame following the end of the transfer. The benefit of this change is that it allows the driver to accept valid URBs which would otherwise be rejected. For example, suppose the schedule length is 1024 frames, the endpoint period is 256 frames, and a four-packet URB is submitted. The four transfers would occupy slots that are 0, 256, 512, and 768 frames past the current frame (plus an extra slop factor). These don't exceed the 1024-frame limit, so the URB should be accepted. But the current code notices that the next available slot would be 1024 frames (plus slop) in the future, which is beyond the limit, and so the URB is rejected unnecessarily. Signed-off-by:
-
