Neither the m25_div_clk nor the m250_div_clk or m250_mux_clk are used in
RMII mode. The m25_div_clk output is routed to the RGMII PHY's "RGMII
clock".
This means that we don't need to configure the clocks in RMII mode. The
driver however did this - with no effect since the clocks are not routed
to the PHY in RMII mode.

While here also rename meson8b_init_clk to meson8b_init_rgmii_tx_clk to
make it easier to understand the code.

Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0dfb33a0 ("sch_red: report backlog information") copied
child's backlog into RED's backlog.  Back then RED did not maintain
its own backlog counts.  This has changed after commit 2ccccf5f
("net_sched: update hierarchical backlog too") and commit d7f4f332
("sch_red: update backlog as well").  Copying is no longer necessary.

Tested:

$ tc -s qdisc show dev veth0
qdisc red 1: root refcnt 2 limit 400000b min 30000b max 30000b ecn
 Sent 20942 bytes 221 pkt (dropped 0, overlimits 0 requeues 0)
 backlog 1260b 14p requeues 14
  marked 0 early 0 pdrop 0 other 0
qdisc tbf 2: parent 1: rate 1Kbit burst 15000b lat 3585.0s
 Sent 20942 bytes 221 pkt (dropped 0, overlimits 138 requeues 0)
 backlog 1260b 14p requeues 14

Recently RED offload was added.  We need to make sure drivers don't
depend on resetting the stats.  This means backlog should be treated
like any other statistic:

  total_stat = new_hw_stat - prev_hw_stat;

Adjust mlxsw.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Nogah Frankel <nogahf@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The latest merge between net and net-next introduced a complier assert in
mlx5 driver.  In hca_cap_bits older fields are kept along with newer
fields that should have replaced them.

Fixes: c02b3741 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Overlapping changes all over.

The mini-qdisc bits were a little bit tricky, however.
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2018-01-17

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) Add initial BPF map offloading for nfp driver. Currently only
   programs were supported so far w/o being able to access maps.
   Offloaded programs are right now only allowed to perform map
   lookups, and control path is responsible for populating the
   maps. BPF core infrastructure along with nfp implementation is
   provided, from Jakub.

2) Various follow-ups to Josef's BPF error injections. More
   specifically that includes: properly check whether the error
   injectable event is on function entry or not, remove the percpu
   bpf_kprobe_override and rather compare instruction pointer
   with original one, separate error-injection from kprobes since
   it's not limited to it, add injectable error types in order to
   specify what is the expected type of failure, and last but not
   least also support the kernel's fault injection framework, all
   from Masami.

3) Various misc improvements and cleanups to the libbpf Makefile.
   That is, fix permissions when installing BPF header files, remove
   unused variables and functions, and also install the libbpf.h
   header, from Jesper.

4) When offloading to nfp JIT and the BPF insn is unsupported in the
   JIT, then reject right at verification time. Also fix libbpf with
   regards to ELF section name matching by properly treating the
   program type as prefix. Both from Quentin.

5) Add -DPACKAGE to bpftool when including bfd.h for the disassembler.
   This is needed, for example, when building libfd from source as
   bpftool doesn't supply a config.h for bfd.h. Fix from Jiong.

6) xdp_convert_ctx_access() is simplified since it doesn't need to
   set target size during verification, from Jesper.

7) Let bpftool properly recognize BPF_PROG_TYPE_CGROUP_DEVICE
   program types, from Roman.

8) Various functions in BPF cpumap were not declared static, from Wei.

9) Fix a double semicolon in BPF samples, from Luis.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull rdma fixes from Doug Ledford:
 "We had a few more items creep up over the last week. Given we are in
  -rc8, these are obviously limited to bugs that have a big downside and
  for which we are certain of the fix.

  The first is a straight up oops bug that all you have to do is read
  the code to see it's a guaranteed 100% oops bug.

  The second is a use-after-free issue. We get away lucky if the queue
  we are shutting down is empty, but if it isn't, we can end up oopsing.
  We really need to drain the queue before destroying it.

  The final one is an issue with bad user input causing us to access our
  port array out of bounds. While fixing the array out of bounds issue,
  it was noticed that the original code did the same thing twice (the
  call to rdma_ah_set_port_num()), so its removal is not balanced by a
  readd elsewhere, it was already where it needed to be in addition to
  where it didn't need to be.

  Summary:

   - Oops fix in hfi1 driver

   - use-after-free issue in iser-target

   - use of user supplied array index without proper checking"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/mlx5: Fix out-of-bound access while querying AH
  IB/hfi1: Prevent a NULL dereference
  iser-target: Fix possible use-after-free in connection establishment error

Jesper Dangaard Brouer says:

====================
This patchset contains some small improvements and cleanup for
the Makefile in tools/lib/bpf/.

It worries me that the libbpf.so shared library is not versioned,
but it not addressed in this patchset.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The third parameter to do_install was not used by $(INSTALL) command.
Fix this by only setting the -m option when the third parameter is supplied.

The use of a third parameter was introduced in commit  eb54e522 ("bpf:
install libbpf headers on 'make install'").

Without this change, the header files are install as executables files (755).

Fixes: eb54e522 ("bpf: install libbpf headers on 'make install'")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The plugin_dir_SQ variable is not used, remove it.
The function update_dir is also unused, remove it.
The variable $VERSION_FILES is empty, remove it.

These all originates from the introduction of the Makefile, and is likely a copy paste
from tools/lib/traceevent/Makefile.

Fixes: 1b76c13e ("bpf tools: Introduce 'bpf' library and add bpf feature check")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

It seems like an oversight not to install the header file for libbpf,
given the libbpf.so + libbpf.a files are installed.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Jakub Kicinski says:

====================
This series combines a number of random improvements ranging from
libbpf to nfp driver.  NFP patches make better use of the verifier
log.  There is a requested adjustment to the map offload code, and
a warning fix for a W=1 build to the disassembler.  Quentin also
fixes the libbpf program type detection, while Jiong allows the use
of libbfd compiled from source.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

If an eBPF instruction is unknown to the driver JIT compiler, we can
reject the program at verification time.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Use the verifier log to output error messages if map lookup
can't be offloaded.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

libbpf is able to deduce the type of a program from the name of the ELF
section in which it is located. However, the comparison is made on the
first n characters, n being determined with sizeof() applied to the
reference string (e.g. "xdp"). When such section names are supposed to
receive a suffix separated with a slash (e.g. "kprobe/"), using sizeof()
takes the final NUL character of the reference string into account,
which implies that both strings must be equal. Instead, the desired
behaviour would consist in taking the length of the string, *without*
accounting for the ending NUL character, and to make sure the reference
string is a prefix to the ELF section name.

Subtract 1 to the total size of the string for obtaining the length for
the comparison.

Fixes: 583c9009 ("libbpf: add ability to guess program type based on section name")
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

bfd.h is requiring including of config.h except when PACKAGE or
PACKAGE_VERSION are defined.

  /* PR 14072: Ensure that config.h is included first.  */
  #if !defined PACKAGE && !defined PACKAGE_VERSION
  #error config.h must be included before this header
  #endif

This check has been introduced since May-2012. It doesn't show up in bfd.h
on some Linux distribution, probably because distributions have remove it
when building the package.

However, sometimes the user might just build libfd from source code then
link bpftool against it. For this case, bfd.h will be original that we need
to define PACKAGE or PACKAGE_VERSION.
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Functions of type bpf_insn_print_t take printf-like format
string, mark the type accordingly.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Daniel suggests it would be more logical for bpf_offload_dev_match()
to return false is either the program or the map are not offloaded,
rather than treating the both not offloaded case as a "matching
CPU/host device".

This makes no functional difference today, since verifier only calls
bpf_offload_dev_match() when one of the objects is offloaded.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Fixes the following sparse warnings:

kernel/bpf/cpumap.c:146:6: warning:
 symbol '__cpu_map_queue_destructor' was not declared. Should it be static?
kernel/bpf/cpumap.c:225:16: warning:
 symbol 'cpu_map_build_skb' was not declared. Should it be static?
kernel/bpf/cpumap.c:340:26: warning:
 symbol '__cpu_map_entry_alloc' was not declared. Should it be static?
kernel/bpf/cpumap.c:398:6: warning:
 symbol '__cpu_map_entry_free' was not declared. Should it be static?
kernel/bpf/cpumap.c:441:6: warning:
 symbol '__cpu_map_entry_replace' was not declared. Should it be static?
kernel/bpf/cpumap.c:454:5: warning:
 symbol 'cpu_map_delete_elem' was not declared. Should it be static?
kernel/bpf/cpumap.c:467:5: warning:
 symbol 'cpu_map_update_elem' was not declared. Should it be static?
kernel/bpf/cpumap.c:505:6: warning:
 symbol 'cpu_map_free' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Pull networking fixes from David Miller:

 1) Two read past end of buffer fixes in AF_KEY, from Eric Biggers.

 2) Memory leak in key_notify_policy(), from Steffen Klassert.

 3) Fix overflow with bpf arrays, from Daniel Borkmann.

 4) Fix RDMA regression with mlx5 due to mlx5 no longer using
    pci_irq_get_affinity(), from Saeed Mahameed.

 5) Missing RCU read locking in nl80211_send_iface() when it calls
    ieee80211_bss_get_ie(), from Dominik Brodowski.

 6) cfg80211 should check dev_set_name()'s return value, from Johannes
    Berg.

 7) Missing module license tag in 9p protocol, from Stephen Hemminger.

 8) Fix crash due to too small MTU in udp ipv6 sendmsg, from Mike
    Maloney.

 9) Fix endless loop in netlink extack code, from David Ahern.

10) TLS socket layer sets inverted error codes, resulting in an endless
    loop. From Robert Hering.

11) Revert openvswitch erspan tunnel support, it's mis-designed and we
    need to kill it before it goes into a real release. From William Tu.

12) Fix lan78xx failures in full speed USB mode, from Yuiko Oshino.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
  net, sched: fix panic when updating miniq {b,q}stats
  qed: Fix potential use-after-free in qed_spq_post()
  nfp: use the correct index for link speed table
  lan78xx: Fix failure in USB Full Speed
  sctp: do not allow the v4 socket to bind a v4mapped v6 address
  sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbuf
  sctp: reinit stream if stream outcnt has been change by sinit in sendmsg
  ibmvnic: Fix pending MAC address changes
  netlink: extack: avoid parenthesized string constant warning
  ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY
  net: Allow neigh contructor functions ability to modify the primary_key
  sh_eth: fix dumping ARSTR
  Revert "openvswitch: Add erspan tunnel support."
  net/tls: Fix inverted error codes to avoid endless loop
  ipv6: ip6_make_skb() needs to clear cork.base.dst
  sctp: avoid compiler warning on implicit fallthru
  net: ipv4: Make "ip route get" match iif lo rules again.
  netlink: extack needs to be reset each time through loop
  tipc: fix a memory leak in tipc_nl_node_get_link()
  ipv6: fix udpv6 sendmsg crash caused by too small MTU
  ...

Currently in the cases where cmp_type == CMP_TYPE_RX_L2_TPA_START_CMP or
CMP_TYPE_RX_L2_TPA_END_CMP the exit path updates cpr->rx_bytes with an
uninitialized length len.  Fix this by adding a new exit path that does
not update the cpr stats with the bogus length len and remove the unused
label next_rx_no_prod.

Detected by CoverityScan, CID#1463807 ("Uninitialized scalar variable")
Fixes: 6a8788f2 ("bnxt_en: add support for software dynamic interrupt moderation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull sound fixes from Takashi Iwai:
 "A few small last-minute fixes that should sneak into 4.15:

   - remove a spurious WARN_ON() triggered by syzkaller

   - fix for ioctl races in ALSA sequencer

   - two trivial HD-audio fixup entries"

* tag 'sound-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: seq: Make ioctls race-free
  ALSA: pcm: Remove yet superfluous WARN_ON()
  ALSA: hda - Apply the existing quirk to iMac 14,1
  ALSA: hda - Apply headphone noise quirk for another Dell XPS 13 variant

Pull tracing fixes from Steven Rostedt:

 - Bring back context level recursive protection in ring buffer.

   The simpler counter protection failed, due to a path when tracing
   with trace_clock_global() as it could not be reentrant and depended
   on the ring buffer recursive protection to keep that from happening.

 - Prevent branch profiling when FORTIFY_SOURCE is enabled.

   It causes 50 - 60 MB in warning messages. Branch profiling should
   never be run on production systems, so there's no reason that it
   needs to be enabled with FORTIFY_SOURCE.

* tag 'trace-v4.15-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Prevent PROFILE_ALL_BRANCHES when FORTIFY_SOURCE=y
  ring-buffer: Bring back context level recursive checks

While working on fixing another bug, I ran into the following panic
on arm64 by simply attaching clsact qdisc, adding a filter and running
traffic on ingress to it:

  [...]
  [  178.188591] Unable to handle kernel read from unreadable memory at virtual address 810fb501f000
  [  178.197314] Mem abort info:
  [  178.200121]   ESR = 0x96000004
  [  178.203168]   Exception class = DABT (current EL), IL = 32 bits
  [  178.209095]   SET = 0, FnV = 0
  [  178.212157]   EA = 0, S1PTW = 0
  [  178.215288] Data abort info:
  [  178.218175]   ISV = 0, ISS = 0x00000004
  [  178.222019]   CM = 0, WnR = 0
  [  178.224997] user pgtable: 4k pages, 48-bit VAs, pgd = 0000000023cb3f33
  [  178.231531] [0000810fb501f000] *pgd=0000000000000000
  [  178.236508] Internal error: Oops: 96000004 [#1] SMP
  [...]
  [  178.311855] CPU: 73 PID: 2497 Comm: ping Tainted: G        W        4.15.0-rc7+ #5
  [  178.319413] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB18A 03/31/2017
  [  178.326887] pstate: 60400005 (nZCv daif +PAN -UAO)
  [  178.331685] pc : __netif_receive_skb_core+0x49c/0xac8
  [  178.336728] lr : __netif_receive_skb+0x28/0x78
  [  178.341161] sp : ffff00002344b750
  [  178.344465] x29: ffff00002344b750 x28: ffff810fbdfd0580
  [  178.349769] x27: 0000000000000000 x26: ffff000009378000
  [...]
  [  178.418715] x1 : 0000000000000054 x0 : 0000000000000000
  [  178.424020] Process ping (pid: 2497, stack limit = 0x000000009f0a3ff4)
  [  178.430537] Call trace:
  [  178.432976]  __netif_receive_skb_core+0x49c/0xac8
  [  178.437670]  __netif_receive_skb+0x28/0x78
  [  178.441757]  process_backlog+0x9c/0x160
  [  178.445584]  net_rx_action+0x2f8/0x3f0
  [...]

Reason is that sch_ingress and sch_clsact are doing mini_qdisc_pair_init()
which sets up miniq pointers to cpu_{b,q}stats from the underlying qdisc.
Problem is that this cannot work since they are actually set up right after
the qdisc ->init() callback in qdisc_create(), so first packet going into
sch_handle_ingress() tries to call mini_qdisc_bstats_cpu_update() and we
therefore panic.

In order to fix this, allocation of {b,q}stats needs to happen before we
call into ->init(). In net-next, there's already such option through commit
d59f5ffa ("net: sched: a dflt qdisc may be used with per cpu stats").
However, the bug needs to be fixed in net still for 4.15. Thus, include
these bits to reduce any merge churn and reuse the static_flags field to
set TCQ_F_CPUSTATS, and remove the allocation from qdisc_create() since
there is no other user left. Prashant Bhole ran into the same issue but
for net-next, thus adding him below as well as co-author. Same issue was
also reported by Sandipan Das when using bcc.

Fixes: 46209401 ("net: core: introduce mini_Qdisc and eliminate usage of tp->q for clsact fastpath")
Reference: https://lists.iovisor.org/pipermail/iovisor-dev/2018-January/001190.htmlReported-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Co-authored-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Co-authored-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

/proc has been ignoring struct file_operations::owner field for 10 years.
Specifically, it started with commit 786d7e16
("Fix rmmod/read/write races in /proc entries"). Notice the chunk where
inode->i_fop is initialized with proxy struct file_operations for
regular files:

	-               if (de->proc_fops)
	-                       inode->i_fop = de->proc_fops;
	+               if (de->proc_fops) {
	+                       if (S_ISREG(inode->i_mode))
	+                               inode->i_fop = &proc_reg_file_ops;
	+                       else
	+                               inode->i_fop = de->proc_fops;
	+               }

VFS stopped pinning module at this point.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to check if p_ent->comp_mode is QED_SPQ_MODE_EBLOCK before
calling qed_spq_add_entry().  The test is fine is the mode is EBLOCK,
but if it isn't then qed_spq_add_entry() might kfree(p_ent).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like qdisc_lookup_class() never existed in the tree
in the git era.  Remove the prototype from the header.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sts variable is holding link speed as well as state.  We should
be using ls to index into ls_to_ethtool.

Fixes: 265aeb51 ("nfp: add support for .get_link_ksettings()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix initialize the uninitialized tx_qlen to an appropriate value when USB
Full Speed is used.

Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have identified a race condition during reception of socket
events and messages in the topology server.

- The function tipc_close_conn() is releasing the corresponding
  struct tipc_subscriber instance without considering that there
  may still be items in the receive work queue. When those are
  scheduled, in the function tipc_receive_from_work(), they are
  using the subscriber pointer stored in struct tipc_conn, without
  first checking if this is valid or not. This will sometimes
  lead to crashes, as the next call of tipc_conn_recvmsg() will
  access the now deleted item.
  We fix this by making the usage of this pointer conditional on
  whether the connection is active or not. I.e., we check the condition
  test_bit(CF_CONNECTED) before making the call tipc_conn_recvmsg().

- Since the two functions may be running on different cores, the
  condition test described above is not enough. tipc_close_conn()
  may come in between and delete the subscriber item after the condition
  test is done, but before tipc_conn_recv_msg() is finished. This
  happens less frequently than the problem described above, but leads
  to the same symptoms.

  We fix this by using the existing sk_callback_lock for mutual
  exclusion in the two functions. In addition, we have to move
  a call to tipc_conn_terminate() outside the mentioned lock to
  avoid deadlock.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
Aquantia atlantic driver update 2018/01

This patch is a set of cleanups and bugfixes in preparation to new
Aquantia hardware support.

Standard ARRAY_SIZE is now used through all the code,
some unused abstraction structures removed and cleaned up,
duplicate declarations removed.

Also two large declaration styling fixes:
- Hardware register set defines are lined up with kernel style
- Hardware access functions were not prefixed, now already
  defined hw_atl prefix is used.

patch v2 changes:
- patch reorganized because of its big size. New HW support
  will be submitted as a separate patchset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

skb len should be fetched before gro_receive - otherwise we may get
wrong or even outdated skb data.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Internal functions for registers and HW access were not prefixed.
This introduce noise in global kernel symbols. Here we add explicit prefix
'hw_atl' to all the HW access layer functions.
Alignment and styling were fixed as well.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Original driver code had internal registers and masks declarations
in low case and without any prefix.
Here we make all these uppercase and add already used HW_ATL prefix
to recognize these.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

aq_nic_s was hidden in aq_nic_internal.h, that made it difficult to access
nic fields and structures from other modules.
This change moves aq_nic_s struct into aq_nic.h and thus makes it available
to other driver modules, mainly pci module and hw related module.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate useless passing of net_device_ops and ethtools_ops through
deep chain of calls.
Move all pci related code into aq_pci_func module.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware operations and capabilities tables are constants and
never changed. Declare these as constants.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use direct aq_hw_s *self reference where possible
Eliminate useless abstraction PHAL, duplicated structures definitions,
Simplify nic config structure creation and management.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Usage of aq_obj_s structure is noop, here we remove it
replacing access to flags filed directly.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>