- 24 Mar, 2014 4 commits
-
-
Shahed Shaikh authored
This patch adds LSO, LSO6 and Tx checksum offload support for VXLAN encapsulated packets on 83xx/84xx series adapters. Signed-off-by:
Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Claudiu Manoil authored
The P1010 device tree restricts the number of supported interrupt groups to 1, although the eth controller can support 2 interrupt groups and the driver assumes the Multi-Group mode ("fsl,etsec2" model). So, in this case the assumption that the Multi-Group mode (MQ_MG_MODE) devices always support 2 interrupt groups is false. To fix this, a check for the actual number of interrupt groups enabled in the board's device tree has been added in gfar_probe for the "fsl,etsec2" devices. Without this fix, P1010 based boards claim support for 2 Tx queues to the net stack but only one is actually allocated, leading to NULL access in xmit. This issue was introduced by enabling Single-Queue polling for the P1010 devices. (71ff9e3d gianfar: Use Single-Queue polling for "fsl,etsec2") Fixes: 71ff9e3dSigned-off-by:Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by:
-
Li RongQing authored
ipv4_ifdown_dst does nothing after IPv4 route caches removal, so we can remove it. Signed-off-by:
Li RongQing <roy.qing.li@gmail.com> Signed-off-by:
-
Eric Dumazet authored
When changing one 16bit value by another in IP header, we can adjust the IP checksum by doing a simple operation described in RFC 1624, as reminded by David. csum_partial() is a complex function on x86_64, not really suited for small number of checksummed bytes. I spotted csum_partial() being in the top 20 most consuming functions (more than 1 %) in a GRO workload, which was rather unexpected. The caller was inet_gro_complete() doing a csum_replace2() when building the new IP header for the GRO packet. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
- 22 Mar, 2014 17 commits
-
-
git://git.open-mesh.org/linux-mergeDavid S. Miller authored
Antonio Quartulli says: ==================== Included changes: - use ether_addr_copy instead of memcpy when possible - implement new multicast packet optimisation - improve several kerneldoc sections - minor code cleanups here you have our patchset for net-next/linux-3.15. They are 16 patches but most of them are just small cleanups and kerneldoc improvements. The only big change is the one from patch 8 to 13 by Linus Lüssing that introduces a new multicast packets optimisation. This new component aims to reduce the air overhead by sending multicast packets as bat-unicast when only one destination exists or by dropping them directly at the source if the multicast group is totally empty. In patch 11 Linus introduces an atomic_t variable, that like others that we already have is only object of write and read, thus making the atomic characteristic totally useless. Unfortunately this is part of our sysfs framework, that helps the developer to introduce new knobs by using few macros only. For this reason we decided to keep Linus' new knob for now, but I'd like to let you know that we are in the process of re-working such framework in order to convert all the current (useless) atomic_t to boolean in one go. ==================== Signed-off-by: -
Simon Wunderlich authored
Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by:
Antonio Quartulli <antonio@meshcoding.com>
-
Antonio Quartulli authored
Add missing documentation for BATADV_DAT_ADDR_MAX and convert an existing documentation to kerneldoc Signed-off-by:
Antonio Quartulli <antonio@open-mesh.com> Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch>
-
Antonio Quartulli authored
Convert the current documentation for the TT flags in proper kerneldoc and improve it by adding an explanation for each of the flags. Signed-off-by:
-
Linus Lüssing authored
With this patch a node sends IPv4 multicast packets to nodes which have a BATADV_MCAST_WANT_ALL_IPV4 flag set and IPv6 multicast packets to nodes which have a BATADV_MCAST_WANT_ALL_IPV6 flag set, too. Why is this needed? There are scenarios involving bridges where multicast report snooping and multicast TT announcements are not sufficient, which would lead to packet loss for some nodes otherwise: MLDv1 and IGMPv1/IGMPv2 have a suppression mechanism for multicast listener reports. When we have an MLDv1/IGMPv1/IGMPv2 querier behind a bridge then our snooping bridge is potentially not going to see any reports even though listeners exist because according to RFC4541 such reports are only forwarded to multicast routers: ----------------------------------------------------------- --------------- {Querier}---|Snoop. Switch|----{Listener} --------------- \ ^ ------- | br0 | < ??? ------- \ _-~---~_ _-~/ ~-_ ~ batman-adv \-----{Sender} \~_ cloud ~/ -~~__-__-~_/ I) MLDv1 Query: {Querier} -> flooded II) MLDv1 Report: {Listener} -> {Querier} -> br0 cannot detect the {Listener} => Packets from {Sender} need to be forwarded to all detected listeners and MLDv1/IGMPv1/IGMPv2 queriers. ----------------------------------------------------------- Note that we do not need to explicitly forward to MLDv2/IGMPv3 queriers, because these protocols have no report suppression: A bridge has no trouble detecting MLDv2/IGMPv3 listeners. Even though we do not support bridges yet we need to provide the according infrastructure already to not break compatibility later. Signed-off-by:Linus Lüssing <linus.luessing@web.de> Signed-off-by:
-
Linus Lüssing authored
With this patch a node may additionally perform the dropping or unicasting behaviour for a link-local IPv4 and link-local-all-nodes IPv6 multicast packet, too. The extra counter and BATADV_MCAST_WANT_ALL_UNSNOOPABLES flag is needed because with a future bridge snooping support integration a node with a bridge on top of its soft interface is not able to reliably detect its multicast listeners for IPv4 link-local and the IPv6 link-local-all-nodes addresses anymore (see RFC4541, section 2.1.2.2 and section 3). Even though this new flag does make "no difference" now, it'll ensure a seamless integration of multicast bridge support without needing to break compatibility later. Also note, that even with multicast bridge support it won't be possible to optimize 224.0.0.x and ff02::1 towards nodes with bridges, they will always receive these ranges. Signed-off-by:
-
Linus Lüssing authored
With this patch a multicast packet is not always simply flooded anymore, the behaviour for the following cases is changed to reduce unnecessary overhead: If all nodes within the horizon of a certain node have signalized multicast listener announcement capability then an IPv6 multicast packet with a destination of IPv6 link-local scope (excluding ff02::1) coming from the upstream of this node... * ...is dropped if there is no according multicast listener in the translation table, * ...is forwarded via unicast if there is a single node with interested multicast listeners * ...and otherwise still gets flooded. Signed-off-by:
-
Linus Lüssing authored
If the soft interface of a node is not part of a bridge then a node announces a new multicast TVLV: The existence of this TVLV signalizes that this node is announcing all of its multicast listeners via the translation table infrastructure. Signed-off-by:
-
Linus Lüssing authored
The new bitfield allows us to keep track whether capability subsets of an originator have gone through their initialization phase yet. The translation table is the only user right now, but a new one will be added soon. Signed-off-by:
-
Linus Lüssing authored
With this patch a node which has no bridge interface on top of its soft interface announces its local multicast listeners via the translation table. Signed-off-by:
-
Antonio Quartulli authored
Some helper functions used along the TX path have now a new "dst_hint" argument but the kerneldoc was missing. Signed-off-by:
-
Marek Lindner authored
Reported-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
-
Simon Wunderlich authored
Reported-by:
-
Antonio Quartulli authored
On some architectures ether_addr_copy() is slightly faster than memcpy() therefore use the former when possible. Signed-off-by:
-
Linus Lüssing authored
Our .ndo_start_xmit handler (batadv_interface_tx()) can rely on having the skb mac header pointer set correctly since the following commit present in kernels >= 3.9: "net: reset mac header in dev_start_xmit()" (6d1ccff6) Therefore this commit removes the according, now redundant, skb_reset_mac_header() call in batadv_bla_tx(). Signed-off-by:
-
Linus Lüssing authored
Our .ndo_start_xmit handler (batadv_interface_tx()) can rely on having the skb mac header pointer set correctly since the following commit present in kernels >= 3.9: "net: reset mac header in dev_start_xmit()" (6d1ccff6) Therefore we can safely use eth_hdr() and vlan_eth_hdr() instead of skb->data now, which spares us some ugly type casts. At the same time set the mac_header in batadv_dat_snoop_incoming_arp_request() before sending the skb along the TX path. Signed-off-by:
-
Fengguang Wu authored
net/batman-adv/network-coding.c:1535:1-7: Replace memcpy with struct assignment Generated by: coccinelle/misc/memcpy-assign.cocci Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Martin Hundebøll <martin@hundeboll.net> Signed-off-by:
-
- 21 Mar, 2014 10 commits
-
-
David S. Miller authored
Richard Cochran says: ==================== ptp: dynamic pin control This patch series introduces a way of changing the auxiliary PTP Hardware Clock functions (periodic output signals and time stamping external signals) at run time. In the past on the netdev list, we have discussed other ways to handle this, such as module parameters and ethtool. This series implements a new PHC ioctl because that is the most natural way. Users already activate the auxiliary functions via the ioctls. The sysfs interface has also been expanded so that the pin configuration can be programmed using shell scripts. The first patch adds the new ioctls. The PHC subsystem does most of the work of maintaining the function-to-pin mapping. Drivers will only need to allocate and initialize a pin configuration table and also provide a new method that validates a particular assignment. Patches 5 and 6 just clean up a couple of issues in the phyter driver, and the remaining patches actually hook the phyter's pins into the new system. * ChangeLog ** V3 - simplify locking in the set pin logic ** V2 - fix bug in sysfs code on init error path - rename ptp_setpin() to ptp_set_pinfunc() - rename .setpin() to .verify() in the driver interface - simplify ptp_find_pin() logic - use correct test when checking whether the pin with the calibration function is being reprogrammed ==================== Signed-off-by: -
Richard Cochran authored
This patch changes the driver use the new pin configuration method when programming the periodic output signal. Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Richard Cochran authored
This patch changes the driver to use the new pin configuration method when programming the external time stamp input signals. Signed-off-by:
-
Richard Cochran authored
This patch adapts the dp83640 driver to allow reconfiguration of which auxiliary function goes on which pin. The functions may be reassigned freely with the one exception of the calibration function. Signed-off-by:
-
Richard Cochran authored
The phyter driver incorrectly feeds the value of the period into what is in fact a pulse width register, resulting in the actual period being twice the dialed value. This patch fixes the issue and renames a variable to make the code at bit more clear. Signed-off-by:
-
Richard Cochran authored
This patch cleans up the input checking code on the external time stamp function by using an unsigned rather than a signed channel index. Also, this patch corrects the author's email address. When this macro was last changed, the top level domain part of the email address was left behind. Signed-off-by:
-
Richard Cochran authored
This patch updates the many PTP Hardware Clock drivers with the newly introduced field that advertises the number of programmable pins. Some of these devices do have programmable pins, but the implementation will have to wait for follow on patches. Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Richard Cochran authored
This patch adds the sysfs hooks needed in order to get and set the programmable pin settings. Signed-off-by:
-
Richard Cochran authored
This patch adds a option to the test program that lists the programmable pins on a PTP Hardware Clock device, assuming there are any such pins. A second option lets the user reprogram the auxiliary function of a single pin. Signed-off-by:
-
Richard Cochran authored
This patch adds a pair of new ioctls to the PTP Hardware Clock device interface. Using the ioctls, user space programs can query each pin to find out its current function and also reprogram a different function if desired. Signed-off-by:
-
- 20 Mar, 2014 9 commits
-
-
David S. Miller authored
Florian Fainelli says: ==================== net: bcmgenet: misc fixes This patch series contains some misc. fixes for the bcmgenet driver. ==================== Signed-off-by: -
Florian Fainelli authored
Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer once and for all and manipulate it throughout bcmgenet_xmit() and bcmgenet_tx_reclaim(). Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
netdev_pick_tx already takes care of making sure that a given skb->queue_mapping value will remain within the number of advertised hardware queue number, there is no need to re-do this again in the driver. Signed-off-by:
-
Florian Fainelli authored
The BCMGENET driver was not TX timestamping the SKBs it queued for transmission, do this in bcmgenet_xmit() right before kicking the Transmit DMA engine. Signed-off-by:
-
Florian Fainelli authored
The spinlock cookie in bcmgenet_priv is never used, get rid of it. Signed-off-by:
-
David S. Miller authored
Laurent Pinchart says: ==================== sh_eth: Fix the race between open and MDIO bus registration This patch series fixes the race condition that exists in the sh_eth driver between network device open and MDIO bus registration. The actual fix is in patch 4/5, with previous patches preparing the driver and patch 5/5 cleaning up an unrelated issue. I've based the idea on Sergei's attempt to fix the problem and can successfully boot the Koelsch board over NFS with this series. I might have missed other issues though, hence the RFC status. The patches are based on top of the latest net-next master branch. ==================== Signed-off-by: -
Laurent Pinchart authored
"goto" is well accepted for error paths in the kernel but should not be used unnecessarily. Return the correct value directly instead of using a goto when possible. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Laurent Pinchart authored
Network API functions that rely on the MDIO bus can be called as soon as the driver calls register_netdev(). Register the MDIO bus before the network device to avoid race conditions. Signed-off-by:
-
Laurent Pinchart authored
The network device passed to the sh_mdio_init and sh_mdio_release functions is only used to access the sh_eth_private instance. Pass it directly to those functions. Signed-off-by:
-
