Because of workqueue delay, the put_device could be called before
device_del, so move it to del_conn.

Signed-off-by: Dave Young <hidave.darkstar@gmail.com> 
Signed-off-by: David S. Miller <davem@davemloft.net>

When a delayed ACK representing two packets arrives, there are two RTT
samples available, one for each packet.  The first (in order of seq
number) will be artificially long due to the delay waiting for the
second packet, the second will trigger the ACK and so will not itself
be delayed.

According to rfc1323, the SRTT used for RTO calculation should use the
first rtt, so receivers echo the timestamp from the first packet in
the delayed ack.  For congestion control however, it seems measuring
delayed ack delay is not desirable as it varies independently of
congestion.

The patch below causes seq_rtt and last_ackt to be updated with any
available later packet rtts which should have less (and hopefully
zero) delack delay.  The rtt value then gets passed to
ca_ops->pkts_acked().

Where TCP_CONG_RTT_STAMP was set, effort was made to supress RTTs from
within a TSO chunk (!fully_acked), using only the final ACK (which
includes any TSO delay) to generate RTTs.  This patch removes these
checks so RTTs are passed for each ACK to ca_ops->pkts_acked().

For non-delay based congestion control (cubic, h-tcp), rtt is
sometimes used for rtt-scaling.  In shortening the RTT, this may make
them a little less aggressive.  Delay-based schemes (eg vegas, veno,
illinois) should get a cleaner, more accurate congestion signal,
particularly for small cwnds.  The congestion control module can
potentially also filter out bad RTTs due to the delayed ack alarm by
looking at the associated cnt which (where delayed acking is in use)
should probably be 1 if the alarm went off or greater if the ACK was
triggered by a packet.
Signed-off-by: Gavin McCullagh <gavin.mccullagh@nuim.ie>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Brownell pointed out a regression in my recent "Fix ip command
line processing" patch. It turns out to be a fairly blatant oversight on
my part whereby ic_enable is never set, and thus autoconfiguration is
never enabled. Clearly my testing was broken :-(

The solution that I have is to set ic_enable to 1 if we hit
ip_auto_config_setup(), which basically means that autoconfiguration is
activated unless told otherwise. I then flip ic_enable to 0 if ip=off,
ip=none, ip=::::::off or ip=::::::none using ic_proto_name();

The incremental patch is below, let me know if a non-incremental version
is prepared, as I did as for the original patch to be reverted pending a
fix.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] PS3: Fix printing of os-area magic numbers
  [POWERPC] Oprofile: Remove dependency on spufs module

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] padlock: Fix spurious ECB page fault

It appears that some PCI-E bridges do the wrong thing in the presense of
CRS Software Visibility and MMCONFIG.  In particular, it looks like an
ATI bridge (device ID 7936) will return 0001 in the vendor ID field of
any bridged devices indefinitely.

Not enabling CRS SV avoids the problem, and as we currently do not
really make good use of the feature anyway (we just time out rather than
do any threaded discovery as suggested by the CRS specs), we're better
off just not enabling it.

This should fix a slew of problem reports with random devices (generally
graphics adapters or fairly high-performance networking cards, since it
only affected PCI-E) not getting properly recognized on these AMD systems.

If we really want to use CRS-SV, we may end up eventually needing a
whitelist of systems where this should be enabled, along with some kind
of "pcibios_enable_crs()" query to call the system-specific code.
Suggested-by: Loic Prylli <loic@myri.com>
Tested-by: Kai Ruhnau <kai@tragetaschen.dyndns.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix a bug in the printing of the os-area magic numbers which assumed
that magic numbers were zero terminated strings.  The magic numbers
are represented in memory as integers.  If the os-area sections are
not initialized correctly they could contained random data that would
be printed to the display.  Also unify the handling of header and db
magic numbers and make both of type array of u8.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This removes an OProfile dependency on the spufs module.  This
dependency was causing a problem for multiplatform systems that are
built with support for Oprofile on Cell but try to load the oprofile
module on a non-Cell system.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The xcryptecb instruction always processes an even number of blocks so
we need to ensure th existence of an extra block if we have to process
an odd number of blocks.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPV4]: Fix ip command line processing.
  [VETH]: move veth.h to include/linux
  [NET] tc_nat: header install
  [TUNTAP]: Fix wrong debug message.
  [NETFILTER]: nf_conntrack_ipv4: fix module parameter compatibility
  mac80211: warn when receiving frames with unaligned data
  mac80211: round station cleanup timer

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Implement pci_resource_to_user()

Did not fix the reported issue. Apart from other weirdness this causes a
bad link between the TLB flushing logic and the quicklists. If there is
indeed an issue that an arch needs a tlb flush before free then the arch
code needs to set tlb->need_flush before calling quicklist_free.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Recently the documentation in Documentation/nfsroot.txt was
update to note that in fact ip=off and ip=::::::off as the
latter is ignored and the default (on) is used.

This was certainly a step in the direction of reducing confusion.
But it seems to me that the code ought to be fixed up so that
ip=::::::off actually turns off ip autoconfiguration.

This patch also notes more specifically that ip=on (aka ip=::::::on)
is the default.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move veth.h from net/ to linux/ since it is a user api, and add it to
user header processing Kbuild.

[ Use header-y as suggested by Sam Ravnborg.  -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

iproute2 build needs tc_nat.h header from kernel make install_headers.
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a trivial fix of debug message.
When a persist flag is set, the message should say "enabled".
Signed-off-by: Toyo Abe <tabe@miraclelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some users do "modprobe ip_conntrack hashsize=...". Since we have the
module aliases this loads nf_conntrack_ipv4 and nf_conntrack, the
hashsize parameter is unknown for nf_conntrack_ipv4 however and makes
it fail.

Allow to specify hashsize= for both nf_conntrack and nf_conntrack_ipv4.

Note: the nf_conntrack message in the ringbuffer will display an
incorrect hashsize since nf_conntrack is first pulled in as a
dependency and calculates the size itself, then it gets changed
through a call to nf_conntrack_set_hashsize().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes mac80211 warn (once) when the driver passes up a
frame in which the payload data is not aligned on a four-byte
boundary, with a long comment for people who run into the condition
and need to know what to do.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The station cleanup timer runs every ten seconds, the exact
timing is not relevant at all so it can well run together with
other things to save power.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This makes libpciaccess able to mmap() resources of the
device properly.
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  cmd64x: fix hwif->chipset setup
  MAINTAINERS: update ide-cd entry
  ide-cd: fix 'ireason' reporting in cdrom_pc_intr()
  ide-cd: fix error message in cdrom_pc_intr()
  ide-cd: add error message for DMA error to cdrom_read_intr()
  ide-cd: fix error messages in cdrom_write_intr()
  ide-cd: add missing 'ireason' masking to cdrom_write_intr()
  ide-cd: fix error messages in cdrom_{read,write}_check_ireason()
  ide-cd: use ide_cd_release() in ide_cd_probe()
  ide-cd: fix ACER/AOpen 24X CDROM speed reporting on big-endian machines
  ide-cd: fix SAMSUNG CD-ROM SCR-3231 quirk
  drivers/ide/: Spelling fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (6876): ivtv: mspx4xx needs a longer i2c udelay
  V4L/DVB (6871): Kconfig: VIDEO_CX23885 must select DVB_LGDT330X

This reverts commit fbdcf18d.

As pointed out by Yanmin Zhang, the problem was already fixed
differently (and correctly), and rather than fix anything, it actually
causes us to create a sub-optimal sched-domains hierarchy (not setting
up the domain belonging to the core) when CONFIG_X86_HT=y.
Requested-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

commit 528a572d ("ide: add ->chipset field
to ide_pci_device_t") broke hwif->chipset setup (it is now set to ide_cmd646
for CMD648 instead of CMD646).  It seems that the breakage happend while
I was moving patches around (cmd64x_chipsets[] entries for CMD646 and CMD648
are identical except for 'name' field).  Fix it and bump driver version.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Reopen ide-cd for maintainership.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Mask 'ireason' variable so only the valid interrupt reason bits
will be reported on "drive appears confused" error.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Mask 'ireason' variable with 0x3 so the valid interrupt reason value
is passed to cdrom_write_check_ireason() for checking.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ide_cd_release() to do the cleanup if ide_cdrom_setup() fails.

It fixes:
- the default drive->dsc_overlap value not being restored
- the default drive->queue's prep_rq_fn not being restored
- struct gendisk 'g' not being freed
- wrong function name being reported on unregister_cdrom() error
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix ACER/AOpen 24X CDROM speed reporting on big-endian machines
  by adding missing le16_to_cpu() calls.

While at it:
* Replace ntohs() by be16_to_cpu().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

cdi->mask is cleared by ide_cdrom_register() which is called after the quirk.

Fix it by adding new ->no_speed_select flag to struct ide_cd_config_flags
and using it in ide_cdrom_register() to set CDC_SELECT_SPEED flag.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  Modules: fix memory leak of module names
  UIO: Add a MAINTAINERS entry for Userspace I/O

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: New device ID for the CP2101 driver
  USB: VID/PID update for sierra
  USB: Unbreak fsl_usb2_udc

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  MACB: clear transmit buffers properly on transmit underrun
  3c359 endianness annotations and fixes
  fec_mpc52xx: write in C...
  3c574 and 3c589 endianness fixes (.24?)
  rrunner: use offsetof() instead of homegrown insanity
  r8169 endianness
  dl2k endianness fixes (.24 fodder?)
  yellowfin: annotations and fixes (.24 fodder?)
  asix fixes
  cycx: annotations and fixes (.24 fodder?)
  typhoon: trivial endianness annotations
  typhoon: memory corruptor on big-endian if TSO is enabled
  typhoon: missed rx overruns on big-endian
  typhoon: set_settings broken on big-endian
  typhoon: missing le32_to_cpu() in get_drvinfo
  typhoon: endianness bug in tx/rx byte counters
  ipw2200: prevent alloc of unspecified size on stack
  iwlwifi: fix possible priv->mutex deadlock during suspend
  p54: add Kconfig description
  rtl8187: Add USB ID for Sitecom WL-168 v1 001