- 27 Aug, 2015 40 commits
-
-
Sreekanth Reddy authored
Add the following OEM's branding to the mpt3sas driver. "VendorID" "DeviceID" "SubsystemVendor ID" "SubsystemDevice ID" Cisco Branding String 0x1000 0x97 SVID = 0x1137 0x014C Cisco 9300-8E 12G SAS HBA Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
Added the following Dell branding to the mpt3sas driver. "VendorID" "DeviceID" "SubsystemVendor ID" "SubsystemDevice ID" Dell Branding String 0x1000 0x0097 0x1028 0x1F46 DELL 12Gbps HBA Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
Following is the change set, 1. Added more defines for the BiosOptions field of MPI2_CONFIG_PAGE_BIOS_1. 2. Added MPI2_TOOLBOX_CLEAN_BIT26_PRODUCT_SPECIFIC definition. Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
This Patch will provide more details of the devices such as slot number, enclosure logical id, enclosure level & connector name in the following scenarios, - When end device is added in the topology, - When the end device is removed from the setup, - When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during error handling, - When any command to the device fails with Sense key Hardware error or Medium error or Unit Attention, - When firmware returns device error or device not ready status for the end device, - When a Predicted fault is detected on an end device. This information can be used by the user to identify the location of the desired drive in the topology. Driver will get these information by reading the sas device page0. Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
Update MPI 2.5 Release: MPI 2.5 Rev I (2.5.4) specification and 2.00.33 header files Below is the change set from the MPI specification for I Rev 1) Added Base Enclosure Level bit to the Flags field of Manufacturing Page 7. 2) Updated description of the MaxTargetPortConnectTime field of SAS IO Unit Page 1. 3) Added EnclosureLevel and ConnectorName fields to SAS Device Page 0. Also, added EnclosureLevel and ConnectorName Valid bit to the Flags field. 4) Added EnclosureLevel field to SAS Enclosure Page 0. Also, added EnclosureLevel Valid bit to the Flags field. 5) Added value for BIOS image to HashImageType. Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
During hot-plugging of a disk(having a flaky link), the disk addition stops and any further disk addition or removal doesn't happen on that controller. This is because, when driver receives DELAY_NOT_RESPONDING event for a disk while it is undergoing addition at the SCSI Transport layer, the driver would block the I/O to that disk resulting in a deadlock. i.e the disk addition work couldn't be completed at the SCSI Transport Layer as it can't send any I/Os (such as Inquiry, Report LUNs etc) to the disk as I/Os are blocked to this drive. Also any subsequent device removal (TARGET_NOT_RESPONDING) or link update(RC_PHY_CHANGED) event couldn't be processed as they are in the queue to get processed after disk addition event. Description of Change: Don't block the drive when drive addition is under the control of SML. So that SML won't be blocked of issuing the device dicovery commands (such as Inquiry, Report LUNs etc). Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
mpt3sas: Get IOC_FACTS information using handshake protocol only after HBA card gets into READY or Operational state. Driver initialization fails if driver tries to send IOC facts request message when the IOC is in reset or in a fault state. This patch will make sure that 1.Driver to send IOC facts request message only if HBA is in operational or ready state. 2.If IOC is in fault state, a diagnostic reset would be issued. 3.If IOC is in reset state then driver will wait for 10 seconds to exit out of reset state. If the HBA continues to be in reset state, then the HBA wouldn't be claimed by the driver. Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to up-to 96. Following are changes that are done in this patch 1. This feature is enabled only for SAS3 C0 and higher revision cards and also only when reply post free queue count is greater than 8. 2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces are used. MSI-X index numbered from 0 to 7 use the first SupplementalReplyPostHostIndex system interface to update its corresponding ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the second SupplementalReplyPostHostIndex system interface and so on. These 12 SuppementalReplyPostHostIndex system interfaces address are saved in the array replyPostRegisterIndex[]. 3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X vectors. So MSIxIndex field in these register must contain a value between 0 and 7. 4. After processing the reply descriptors from a reply post free queues then update the new reply post host index value in ReplyPostHostIndex field and (msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex register. The Address of this SupplementalReplyPostHostIndex register is retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array. Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Dan Carpenter authored
We recently did some cleanup here and now the static checkers notice that there is a missing error code when ioremap() fails. Let's set it to -ENOMEM. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
K. Y. Srinivasan authored
In the function storvsc_channel_init(), error code was not getting set correctly in some of the failure cases. Fix this issue. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Keith Mange authored
Allow WRITE_SAME for Windows10 and above hosts. Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: Keith Mange <keith.mange@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Keith Mange authored
Use storage protocol version instead of vmbus protocol version when determining storage capabilities. Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: Keith Mange <keith.mange@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Keith Mange authored
Use correct defaults for values determined by protocol negotiation, instead of resetting them with every scsi controller. Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: Keith Mange <keith.mange@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Keith Mange authored
Currently we are making decisions based on vmbus protocol versions that have been negotiated; use storage potocol versions instead. [jejb: fold ARRAY_SIZE conversion suggested by Johannes Thumshirn <jthumshirn@suse.de> make vmstor_protocol static] Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: Keith Mange <keith.mange@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Keith Mange authored
Use a single value to track protocol versions to simplify comparisons and to be consistent with vmbus version tracking. Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: Keith Mange <keith.mange@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Keith Mange authored
Rather than look for sets of specific protocol versions, make decisions based on ranges. This will be safer and require fewer changes going forward as we add more storage protocol versions. Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: Keith Mange <keith.mange@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Matthew R. Ochs authored
The queuecommand routine has a local dev pointer used for the dev_* prints. The two prints that currently exist are tucked under a debug define and thus can be left out. Use the actual location instead of a local to avoid this warning. This patch is intended to be applied after the "CXL Flash Error Recovery and Superpipe" series. Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Dan Carpenter authored
"port_sel" is a u64 so the shifting should also be a 64 bit shift. Fixes: c21e0bbf ('cxlflash: Base support for IBM CXL Flash Adapter') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Dan Carpenter authored
The > should be >= or we read one element past the end of the array. Fixes: c21e0bbf ('cxlflash: Base support for IBM CXL Flash Adapter') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Matthew R. Ochs authored
Add support for physical LUN segmentation (virtual LUNs) to device driver supporting the IBM CXL Flash adapter. This patch allows user space applications to virtually segment a physical LUN into N virtual LUNs, taking advantage of the translation features provided by this adapter. Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com> Reviewed-by: Michael Neuling <mikey@neuling.org> Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Matthew R. Ochs authored
Add superpipe supporting infrastructure to device driver for the IBM CXL Flash adapter. This patch allows userspace applications to take advantage of the accelerated I/O features that this adapter provides and bypass the traditional filesystem stack. Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com> Reviewed-by: Michael Neuling <mikey@neuling.org> Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Matthew R. Ochs authored
Introduce support for enhanced I/O error handling. A device state is added to track 3 possible states of the device: Normal - the device is operating normally and is fully operational Limbo - the device is in a reset/recovery scenario and its operational status is paused Failed/terminating - the device has either failed to be reset/recovered or is being terminated (removed); it is no longer operational All operations are allowed when the device is operating normally. When the device transitions to limbo state, I/O must be paused. To help accomplish this, a wait queue is introduced where existing and new threads can wait until the device is no longer in limbo. When coming out of limbo, threads need to check the state and error out gracefully when encountering the failed state. When the device transitions to the failed/terminating state, normal operations are no longer allowed. Only specially designated operations related to graceful cleanup are permitted. Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com> Reviewed-by: Daniel Axtens <dja@axtens.net> Reviewed-by: Michael Neuling <mikey@neuling.org> Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Himanshu Madhani authored
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sawan Chandak authored
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Arun Easi authored
On certain conditions, login failures will just invoke qla2x00_mark_device_lost() with the intend to do login again; but if login_retry has been set already, that would fail to set the relogin needed flag which is required to wakeup the DPC to retry. Signed-off-by: Arun Easi <arun.easi@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Himanshu Madhani authored
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Chad Dupuis authored
Fix for memory leak when command is not found by firmware due to mismatch in sp reference count. Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Sawan Chandak authored
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Chad Dupuis authored
Instead of resetting the adapter wait for the login to timeout and retry. Resetting the adapter can cause extended path recovery times. Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Chad Dupuis authored
If an SRB is NULL but the handle is in range just drop the command instead of also resetting the adapter. If the handle is in range then the command was valid at some point and may have been aborted. Resetting the adapter can lead to extended recovery times in this case. Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Hiral Patel authored
Aovid crashing the system in the scenario where firmware just completes the command and it can not find the command during abort mailbox processing. This scenario can lead to sp reference counter being zero. Instead of crashing the system, use WARN_ON to print warning in log file. Signed-off-by: Hiral Patel <hiral.patel@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Saurav Kashyap authored
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Joe Carnuccio authored
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Joe Carnuccio authored
Execute qla25xx_manipulate_risc_semaphore() only for ssdid 0x0175 and 0x0240. Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Joe Carnuccio authored
When we get logged out, mark the port lost and set dpc flag for relogin. Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
Joe Carnuccio authored
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-
jiang.biao2@zte.com.cn authored
scsi_error: should not get sense for timeout IO in scsi error handler When an IO timeout occurs, the IO will be aborted in scsi_abort_command() and SCSI_EH_ABORT_SCHEDULED will be set. Because of that, the SCSI_EH_CANCEL_CMD will be clear in scsi_eh_scmd_add(). So when scsi error handler starts, it will get sense for this timeout IO and the scmd of the IO request will be reused. In that case, the scmd may be double released when racing with io_done(), which will result in crash. SO SCSI_EH_ABORT_SCHEDULED should also be checked when getting sense. The bug maybe reproduced when the link between host and disk is unstable. Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn> Signed-off-by: Long Chun <long.chun@zte.com.cn> Reviewed-by: Tan Hu <tan.hu@zte.com.cn> Reviewed-by: Chen Donghai <chen.donghai@zte.com.cn> Reviewed-by: Cai Qu <cai.qu@zte.com.cn> Signed-off-by: James Bottomley <JBottomley@Odin.com>
-