This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller.  But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.

The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller.  If it has, the
error message is suppressed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1095) cleans up the HCD glue and several of the EHCI
bus-glue files.  The ehci->is_tdi_rh_tt flag is redundant, since it
means the same thing as the hcd->has_tt flag, so it is removed and the
other flag used in its place.

Some of the bus-glue files didn't get the relinquish_port method added
to their hc_driver structures.  Although that routine currently
doesn't do anything for controllers with an integrated TT, in the
future it might.  So the patch adds it where it is missing.

Lastly, some of the bus-glue files have erroneous entries for their
hc_driver's suspend and resume methods.  These method pointers are
specific to PCI and shouldn't be used otherwise.

(The patch also includes an invisible whitespace fix.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>

This patch (as1094) changes the output of the "descriptors" binary
attribute.  Now it will contain the device descriptor followed by all
the configuration descriptors, not just the descriptor for the current
config.

Userspace libraries want to have access to the kernel's cached
descriptor information, so they can learn about device characteristics
without having to wake up suspended devices.  So far the only user of
this attribute is the new libusb-1.0 library; thus changing its
contents shouldn't cause any problems.

This should be considered for 2.6.26, if for no other reason than to
minimize the range of releases in which the attribute contains only the
current config descriptor.

Also, it doesn't hurt that the patch removes the device locking --
which was formerly needed in order to know for certain which config was
indeed current.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

There is a potential deadlock when the usb_generic driver is unbound
from a device.  The problem is that generic_disconnect() is called
with the device lock held, and it removes a bunch of device attributes
from sysfs.  If a user task happens to be running an attribute method
at the time, the removal will block until the method returns.  But at
least one of the attribute methods (the store routine for power/level)
needs to acquire the device lock!

This patch (as1093) eliminates the deadlock by moving the calls to
create and remove the sysfs attributes from the usb_generic driver
into usb_new_device() and usb_disconnect(), where they can be invoked
without holding the device lock.

Besides, the other sysfs attributes are created when the device is
registered and removed when the device is unregistered.  So it seems
only fitting for the extra attributes to be created and removed at the
same time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Uninitialised Apple iSight drivers present with a distinctive USB ID.
Once firmware has been uploaded, they disconnect and reconnect with a
new ID. At this point they can be driven by the uvcvideo driver. As this
is unique to the Apple cameras and not functionality shared by any other
UVC devices, it makes sense to provide the firmware loading
functionality in a separate driver. This driver will read an isight.fw
file extracted from the Apple driver using the tools at
http://bersace03.free.fr/ift/ and upload it to the camera. It will also
handle the case where the device loses its firmware during hibernation
and must have it reloaded.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.

A small number of units have been shipped early 2008
with a faulty USB Descriptor.  Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: R. Molenkamp <rmolenkamp@matrixorbital.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

> +#define	ARCH_KMALLOC_MINALIGN		(sizeof(long) * 2)
> +#define	ARCH_SLAB_MINALIGN		(sizeof(long) * 2)

This doesn't work if SLAB is selected and slab debugging is enabled as
these are passed to the preprocessor, and the preprocessor doesn't
understand sizeof.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  cfq-iosched: fix RCU problem in cfq_cic_lookup()
  block: make blktrace use per-cpu buffers for message notes
  Added in elevator switch message to blktrace stream
  Added in MESSAGE notes for blktraces
  block: reorder cfq_queue to save space on 64bit builds
  block: Move the second call to get_request to the end of the loop
  splice: handle try_to_release_page() failure
  splice: fix sendfile() issue with relay

Specify the minimum slab/kmalloc alignment to be 8 bytes.  This fixes a
crash when SLOB is selected as the memory allocator.  The FRV arch needs
this so that it can use the load- and store-double instructions without
faulting.  By default SLOB sets the minimum to be 4 bytes.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix a typo in the header guard of asm/ipc.h.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cfq_cic_lookup() needs to properly protect ioc->ioc_data before
dereferencing it and also exclude updaters of ioc->ioc_data as well.

Also add a number of comments documenting why the existing RCU usage
is OK.

Thanks a lot to "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> for
review and comments!
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

Currently it uses a single static char array, but that risks
being corrupted when multiple users issue message notes at the
same time. Make the buffers dynamically allocated when the trace
is setup and make them per-cpu instead.

The default max message size of 1k is also very large, the
interface is mainly for small text notes. So shrink it to 128 bytes.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

Allows messages to be inserted into blktrace streams.
Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

saves 8 bytes of padding & increases objects/slab from 30 to 32 on my
AMD64 config
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

In function get_request_wait, the second call to get_request could be
moved to the end of the while loop, because if the first call to
get_request fails, the second call will fail without sleep.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

splice currently assumes that try_to_release_page() always suceeds,
but it can return failure. If it does, we cannot steal the page.

Acked-by: Mingming Cao <cmm@us.ibm.com
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

Splice isn't always incrementing the ppos correctly, which broke
relay splice.
Signed-off-by: Tom Zanussi <zanussi@comcast.net>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  pciehp: add message about pciehp_slot_with_bus option
  pci hotplug core: add check of duplicate slot name
  pciehp: move msleep after power off
  pciehp: poll cmd completion if hotplug interrupt is disabled
  pciehp: fix slow probing
  pciehp: fix NULL dereference in interrupt handler
  shpchp: add message about shpchp_slot_with_bus option
  PCI: don't enable ASPM on devices with mixed PCIe/PCI functions

Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The pciehp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Fix the following errors reported by Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.

kobject_add_internal failed for 2 with -EEXIST, don't try to register things with the same name in the same directory.
Pid: 1, comm: swapper Tainted: G        W 2.6.26-rc3 #1
 [<c0266980>] kobject_add_internal+0x140/0x190
 [<c0266afd>] kobject_init_and_add+0x2d/0x40
 [<c027bc91>] pci_hp_register+0x81/0x2f0
 [<c027fd07>] pciehp_probe+0x1a7/0x470
 [<c01b3b84>] sysfs_add_one+0x44/0xa0
 [<c01b3c1f>] sysfs_addrm_start+0x3f/0xb0
 [<c01b497a>] sysfs_create_link+0x8a/0xf0
 [<c0279570>] pcie_port_probe_service+0x50/0x80
 [<c02e0545>] driver_sysfs_add+0x55/0x70
 [<c02e0662>] driver_probe_device+0x82/0x180
 [<c02e07cc>] __driver_attach+0x6c/0x70
 [<c02dfe0a>] bus_for_each_dev+0x3a/0x60
 [<c05db2d0>] pcied_init+0x0/0x80
 [<c02e04e6>] driver_attach+0x16/0x20
 [<c02e0760>] __driver_attach+0x0/0x70
 [<c02e0341>] bus_add_driver+0x1a1/0x220
 [<c05db2d0>] pcied_init+0x0/0x80
 [<c02e09cd>] driver_register+0x4d/0x120
 [<c05db050>] ibm_acpiphp_init+0x0/0x190
 [<c0125aab>] printk+0x1b/0x20
 [<c05db2d0>] pcied_init+0x0/0x80
 [<c05db2de>] pcied_init+0xe/0x80
 [<c05c751a>] kernel_init+0x10a/0x300
 [<c0120138>] schedule_tail+0x18/0x50
 [<c0103b9a>] ret_from_fork+0x6/0x1c
 [<c05c7410>] kernel_init+0x0/0x300
 [<c05c7410>] kernel_init+0x0/0x300
 [<c010485b>] kernel_thread_helper+0x7/0x1c
 =======================
pci_hotplug: Unable to register kobject '2'<3>pciehp: pci_hp_register failed with error -22

Slot with the same name can be registered multiple times if shpchp or
pciehp driver is loaded after acpiphp is loaded because ACPI based
hotplug driver and Native OS hotplug driver trying to handle the same
physical slot. In this case, current pci_hotplug core will call
kobject_init_and_add() muliple time with the same name. This is the
cause of this problem. To fix this problem, this patch adds the check
into pci_hp_register() to see if the slot with the same name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

According to the PCI Express specification, we must wait for at least
1 second after turning power off before taking any action that relies
on power having been removed from the slot/adapter. For this, current
pciehp wait for 1 second after issuing the power off command in
hpc_power_off_slot() function. But waiting for 1 second in
hpc_power_off_slot() can make pciehp probing slow-down because pciehp
probe code calls hpc_power_off_slot() if the slot is not occupied just
in case. We don't need to wait for 1 second at the pciehp probe time
because there is no action on that empty slot. So move 1 second wait
from hpc_power_off_slot() to the caller of hpc_power_off_slot().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Fix improper long wait for command completion in pciehp probing.

As described in PCI Express specification, software notification is
not generated if the command that occurs as a result of a write to the
Slot Control register that disables software notification of command
completed events. Since pciehp driver doesn't take it into account,
such command is issued in pciehp probing, and it causes improper long
wait for command completion.

This patch changes the pciehp driver to take such command into
account.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.

The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).

The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.

This problem seems to be revealed by the commit
c27fb883 that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Fix the following NULL dereference problem reported from Pierre Ossman
and Ingo Molnar.

pciehp: HPC vendor_id 8086 device_id 27d0 ss_vid 0 ss_did 0
pciehp: pciehp_find_slot: slot (device=0x0) not found
BUG: unable to handle kernel NULL pointer dereference at 0000000000000070
IP: [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
PGD 0
Oops: 0000 [1]
CPU 0
Modules linked in:
Pid: 1, comm: swapper Tainted: G        W 2.6.26-rc3-sched-devel.git-00001-g2b99b26-dirty #170
RIP: 0010:[<ffffffff80494a8b>]  [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
RSP: 0000:ffff81003f83fbb0  EFLAGS: 00010046
RAX: 0000000000000039 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000046
RBP: ffff81003f83fbd0 R08: 0000000000000001 R09: ffffffff80245103
R10: 0000000000000020 R11: 0000000000000000 R12: ffff81003ea53a30
R13: 0000000000000000 R14: 0000000000000011 R15: ffffffff80495926
FS:  0000000000000000(0000) GS:ffffffff80be7400(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000070 CR3: 0000000000201000 CR4: 00000000000006a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 1, threadinfo ffff81003f83e000, task ffff81003f840000)
Stack:  0000000000000008 ffff81003f83fbf6 ffff81003ea53a30 0000000000000008
 ffff81003f83fc10 ffffffff80495ab4 0000000000000011 0000000000000002
 0000000000000202 0000000000000202 00000000fffffff4 ffff81003ea53a30
Call Trace:
 [<ffffffff80495ab4>] pcie_isr+0x18e/0x1bc
 [<ffffffff80260831>] request_irq+0x106/0x12f
 [<ffffffff80495fb6>] pcie_init+0x15e/0x6cc
 [<ffffffff804933a3>] pciehp_probe+0x64/0x541
 [<ffffffff8048f4e7>] pcie_port_probe_service+0x4c/0x76
 [<ffffffff8054af70>] driver_probe_device+0xd4/0x1f0
 [<ffffffff8054b108>] __driver_attach+0x7c/0x7e
 [<ffffffff8054b08c>] ? __driver_attach+0x0/0x7e
 [<ffffffff8054a4b6>] bus_for_each_dev+0x53/0x7d
 [<ffffffff8054ad3c>] driver_attach+0x1c/0x1e
 [<ffffffff8054a9c2>] bus_add_driver+0xdd/0x25b
 [<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
 [<ffffffff8054b288>] driver_register+0x5f/0x13e
 [<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
 [<ffffffff8048f441>] pcie_port_service_register+0x47/0x49
 [<ffffffff80c09d52>] pcied_init+0x15/0x8b
 [<ffffffff80bf3938>] kernel_init+0x75/0x243
 [<ffffffff808639d2>] ? _spin_unlock_irq+0x2b/0x3a
 [<ffffffff80228d1f>] ? finish_task_switch+0x57/0x9a
 [<ffffffff8020c258>] child_rip+0xa/0x12
 [<ffffffff8020bcec>] ? restore_args+0x0/0x30
 [<ffffffff80bf38c3>] ? kernel_init+0x0/0x243
 [<ffffffff8020c24e>] ? child_rip+0x0/0x12

Code: 83 80 00 00 00 48 39 f0 75 e1 0f b6 c9 48 c7 c2 00 0e 8d 80 48 c7 c6 8a 60 a6 80 48 c7 c7 10 db a8 80 31 c0 e8 3f 8d d9 ff 31 db <48> 8b 43 70 48 8d 75 ef 48 89 df ff 50 30 80 7d ef 00 74 37 48
RIP  [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
 RSP <ffff81003f83fbb0>
CR2: 0000000000000070
Kernel panic - not syncing: Fatal exception

The situation under which it occurs is hw and timing related: it appears
to happen on a system that has PCI hotplug hardware but with no active
hotplug cards, and another interrupt in the same (shared) IRQ line
arrives too early, before the hotplug-slot entry has been set up - as
triggered by CONFIG_DEBUG_SHIRQ=y:

This patch contains the following two fixes.

(1) Clear all events bits in Slot Status register to prevent the pciehp
    driver from detecting the spurious events that would have been occur
    before pciehp loading.

(2) Add check whether slot initialization had been already done.

This is short term fix. We need more structural fixes to install
interrupt handler after slot initialization is done.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: Fix cpufreq oops when ondemand governor is default
  avr32: Update defconfigs
  avr32: export strnlen_user
  avr32: export copy_page

There's a reason why using C99 initialisers even in the supposedly
trivial structs is a good idea.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Move the AP7 cpufreq init to late_initcall() so that we don't try to
bring up cpufreq until the governor is ready. x86 also uses
late_initcall() for this.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>

Based on Roland's patch. This approach was suggested by Austin Clements
from the very beginning, and then by Linus.

As Austin pointed out, the execing task can be killed by SI_TIMER signal
because exec flushes the signal handlers, but doesn't discard the pending
signals generated by posix timers. Perhaps not a bug, but people find this
surprising. See http://bugzilla.kernel.org/show_bug.cgi?id=10460Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently sigqueue_free() removes sigqueue from list, but doesn't cancel the
pending signal. This is not consistent, the task should either receive the
"full" signal along with siginfo_t, or it shouldn't receive the signal at all.

Change sigqueue_free() to clear SIGQUEUE_PREALLOC but leave sigqueue on list
if it is queued.

This is a user-visible change. If the signal is blocked, it stays queued
after sys_timer_delete() until unblocked with the "stale" si_code/si_value,
and of course it is still counted wrt RLIMIT_SIGPENDING which also limits
the number of posix timers.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Align i2c_device_id
  tuner: Do not alter i2c_client.name

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: ksize() abuse checks
  slob: Fix to return wrong pointer

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.26:
  sh: Drop broken URAM support on SH7723.
  sh: update Migo-R defconfig
  sh: use sm501 8250 mfd support on r2d boards
  sh: add probe support for new sh7723 cut
  sh: fix VPU interrupt vector for sh7723
  sh: fix USBF resource for sh7722

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: global_reg_snapshot is not for userspace

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
  vlan: Use bitmask of feature flags instead of seperate feature bits
  fmvj18x_cs: add NextCom NC5310 rev B support
  xirc2ps_cs: re-initialize the multicast address in do_reset
  3C509: rx_bytes should not be increased when alloc_skb failed
  NETFRONT: Use __skb_queue_purge()
  VIRTIO: Use __skb_queue_purge()
  phylib: do EXPORT_SYMBOL on get_phy_id
  netlink: Fix nla_parse_nested_compat() to call nla_parse() directly
  WAN: protect HDLC proto list while insmod/rmmod
  drivers/net/fs_enet: remove null pointer dereference
  S2io: Version update for napi and MSI-X patches
  S2io: Added napi support when MSIX is enabled.
  S2io: Move all the transmit completions to a single msi-x (alarm) vector
  drivers/net/ehea - remove unnecessary memset after kzalloc
  au1000_eth: remove useless check
  Blackfin EMAC Driver: Removed duplicated include <linux/ethtool.h>
  cpmac bugfixes and enhancements
  e1000e: use resource_size_t, not unsigned long, for phys addrs
  net/usb: add support for Apple USB Ethernet Adapter
  uli526x: add support for netpoll
  ...

Align i2c_device_id.driver_data to 8 bytes to not fail on crossbuilds.

(Added in d2653e92.)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The tuner driver used to change i2c_client.name for its own needs, but
it really shouldn't, as this field is used by i2c-core to do the
device/driver matching. So, create and use a separate field for the
tuner driver needs.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Just provide reasonable defaults for the new stuff. Tickless and
hrtimers are turned on for all boards except ATSTK1004.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>