Remove the indirect MMD read/write methods which are now no longer
necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert micrel to the new read_mmd/write_mmd driver methods.  This
Clause 22 PHY does not support any MMD access method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch everyone over to using phy_read_mmd() and phy_write_mmd() now
that they are able to handle both Clause 22 indirect addressing and
Clause 45 direct addressing methods to the MMD registers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan78xx appears to use phylib in a rather weird way, accessing the PHY
partly through phylib, and partly by making direct accesses to it,
including to the Clause 45 registers.  As the indirect MMD accessors are
going away, update this driver to use the plain phy_(read|write)_mmd()
accessors instead.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make phy_(read|write)_mmd() generic 802.3 clause 45 register accessors
for both Clause 22 and Clause 45 PHYs, using either the direct register
reading for Clause 45, or the indirect method for Clause 22 PHYs.
Allow this behaviour to be overriden by PHY drivers where necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the phy_(read|write)__mmd() helpers out of line, they will become
our main MMD accessor functions, and so will be a little more complex.
This complexity doesn't belong in an inline function.  Also move the
_indirect variants as well to keep like functionality together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to the recent multi-queue changes the driver would configure the
queues to use the AVB mode, but the mode then got switched to DCB. The
hardware still works fine in DCB mode, but my testing capabilities are
limited, so it's safer to revert to the prior setting anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent changes to support multiple queues in the device tree bindings
resulted in the number of RX and TX queues to be initialized to zero for
device trees not adhering to the new bindings.

Restore backwards-compatibility with those device trees by falling back
to a single RX and TX queues each.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC RX queues always need to be enabled in order to receive network
packets. Remove the condition that this only needs to be done for multi-
queue configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address() which
looks up the MAC address using the 3 typical property names.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix Coverity scan errors by not dereferencing lio->glists_dma_base pointer
if it's NULL.

See http://marc.info/?l=linux-netdev&m=149002294305614&w=2Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: VSR Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When user_mss is zero, it means use the default value. But the current
codes don't permit user set TCP_MAXSEG to the default value.
It would return the -EINVAL when val is zero.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andy Zhou says:

====================
net-next sample action optimization v4

The sample action can be used for translating Openflow 'clone' action.
However its implementation has not been sufficiently optimized for this
use case. This series attempts to close the gap.

Patch 3 commit message has more details on the specific optimizations
implemented.

---
v3->v4: Enhance patch 4.
        Fix two bugs pointed out by Pravin,
        Remove 'is_sample' variable.

v2->v3: Enhance patch 4, Rafctor to move more common logic to clone_execute().

v1->v2: Address Pravin's comment, Refactor recirc and sample
        to share more common code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Added clone_execute() that both the sample and the recirc
action implementation can use.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the introduction of open flow 'clone' action, the OVS user space
can now translate the 'clone' action into kernel datapath 'sample'
action, with 100% probability, to ensure that the clone semantics,
which is that the packet seen by the clone action is the same as the
packet seen by the action after clone, is faithfully carried out
in the datapath.

While the sample action in the datpath has the matching semantics,
its implementation is only optimized for its original use.
Specifically, there are two limitation: First, there is a 3 level of
nesting restriction, enforced at the flow downloading time. This
limit turns out to be too restrictive for the 'clone' use case.
Second, the implementation avoid recursive call only if the sample
action list has a single userspace action.

The main optimization implemented in this series removes the static
nesting limit check, instead, implement the run time recursion limit
check, and recursion avoidance similar to that of the 'recirc' action.
This optimization solve both #1 and #2 issues above.

One related optimization attempts to avoid copying flow key as
long as the actions enclosed does not change the flow key. The
detection is performed only once at the flow downloading time.

Another related optimization is to rewrite the action list
at flow downloading time in order to save the fast path from parsing
the sample action list in its original form repeatedly.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The logic of allocating and copy key for each 'exec_actions_level'
was specific to execute_recirc(). However, future patches will reuse
as well.  Refactor the logic into its own function clone_key().
Signed-off-by: Andy Zhou <azhou@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

add_deferred_actions() API currently requires actions to be passed in
as a fully encoded netlink message. So far both 'sample' and 'recirc'
actions happens to carry actions as fully encoded netlink messages.
However, this requirement is more restrictive than necessary, future
patch will need to pass in action lists that are not fully encoded
by themselves.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: vrf: performance improvements

Device based features for VRF such as qdisc, netfilter and packet
captures are implemented by switching the dst on skbuffs to its per-VRF
dst. This has the effect of controlling the output function which points
a function in the VRF driver. [1] The skb proceeds down the stack with
dst->dev pointing to the VRF device. Netfilter, qdisc and tc rules and
network taps are evaluated based on this device. Finally, the skb makes
it to the vrf_xmit function which resets the dst based on a FIB lookup.

The feature comes at cost - between 5 and 10% depending on test (TCP vs
UDP, stream vs RR and IPv4 vs IPv6). The main cost is requiring a FIB
lookup in the VRF driver for each packet sent through it. The FIB lookup
is required because the real dst gets dropped so that the skb can
traverse the stack with dst->dev set to the VRF device.

All of that is really driven by the qdisc and not replicating the
processing of __dev_queue_xmit if a qdisc is set up on the device. But,
VRF devices by default do not have a qdisc and really have no need for
multiple Tx queues. This means the performance overhead is inflicted upon
all users for the potential use case of a qdisc being configured.

The overhead can be avoided by checking if the default configuration
applies to a specific VRF device before switching the dst. If a device
does not have a qdisc, the pass through netfilter hooks and packet taps
can be done inline without dropping the dst and thus avoiding the
performance penalty. With this change performance overhead of VRF drops
to neglible (difference with run-over-run variance) to 3% depending on
test type.

netperf performance comparison for 3 cases:
1. L3_MASTER_DEVICE compiled out
2. VRF with this patch set
3. current VRF code

IPv4
----
           no-l3mdev     new-vrf     old-vrf
TCP_RR       28778        28938*       27169
TCP_CRR      10706        10490         9770
UDP_RR       30750        29813        29256

* Although higher in the final run used for submitting this patch set, I
  think what this really represents is a neglible performance overhead for
  VRF with this change (i.e, within the +-1% variance of runs). Most
  notably the FIB lookups in the Tx path are avoided for TCP_RR.

IPv6
----
           no-l3mdev     new-vrf     old-vrf
TCP_RR       29495        29432       27794
TCP_CRR      10520        10338        9870
UDP_RR       26137        27019*      26511

* UDP is consistently better with VRF for two reasons:
  1. Source address selection with L3 domains is considering fewer
     addresses since only addresses on interfaces in the domain are
     considered for the selection. Specifically, perf-top shows
     shows ipv6_get_saddr_eval, ipv6_dev_get_saddr and __ipv6_dev_get_saddr
     running much lower with vrf than without.

  2. The VRF table contains all routes (i.e, there are no separate local
     and main tables per VRF). That means ip6_pol_route_output only has 1
     lookup for VRF where it does 2 without it (1 in the local table and 1
     in the main table).

[1] http://netdevconf.org/1.2/papers/ahern-what-is-l3mdev-paper.pdf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The VRF driver allows users to implement device based features for an
entire domain. For example, a qdisc or netfilter rules can be attached
to a VRF device or tcpdump can be used to view packets for all devices
in the L3 domain.

The device-based features come with a performance penalty, most
notably in the Tx path. The VRF driver uses the l3mdev_l3_out hook
to switch the dst on an skb to its private dst. This allows the skb
to traverse the xmit stack with the device set to the VRF device
which in turn enables the netfilter and qdisc features. The VRF
driver then performs the FIB lookup again and reinserts the packet.

This patch avoids the redirect for IPv6 packets if a qdisc has not
been attached to a VRF device which is the default config. In this
case the netfilter hooks and network taps are directly traversed in
the l3mdev_l3_out handler. If a qdisc is attached to a VRF device,
then the redirect using the vrf dst is done.

Additional overhead is removed by only checking packet taps if a
socket is open on the device (vrf_dev->ptype_all list is not empty).
Packet sockets bound to any device will still get a copy of the
packet via the real ingress or egress interface.

The end result of this change is a decrease in the overhead of VRF
for the default, baseline case (ie., no netfilter rules, no packet
sockets, no qdisc) from a +3% improvement for UDP which has a lookup
per packet (VRF being better than no l3mdev) to ~2% loss for TCP_CRR
which connects a socket for each request-response.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VRF driver allows users to implement device based features for an
entire domain. For example, a qdisc or netfilter rules can be attached
to a VRF device or tcpdump can be used to view packets for all devices
in the L3 domain.

The device-based features come with a performance penalty, most
notably in the Tx path. The VRF driver uses the l3mdev_l3_out hook
to switch the dst on an skb to its private dst. This allows the skb
to traverse the xmit stack with the device set to the VRF device
which in turn enables the netfilter and qdisc features. The VRF
driver then performs the FIB lookup again and reinserts the packet.

This patch avoids the redirect for IPv4 packets if a qdisc has not
been attached to a VRF device which is the default config. In this
case the netfilter hooks and network taps are directly traversed in
the l3mdev_l3_out handler. If a qdisc is attached to a VRF device,
then the redirect using the vrf dst is done.

Additional overhead is removed by only checking packet taps if a
socket is open on the device (vrf_dev->ptype_all list is not empty).
Packet sockets bound to any device will still get a copy of the
packet via the real ingress or egress interface.

The end result of this change is a decrease in the overhead of VRF
for the default, baseline case (ie., no netfilter rules, no packet
sockets, no qdisc) to ~3% for UDP which has a lookup per packet and
< 1% overhead for connected sockets that leverage early demux and
avoid FIB lookups.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allows reading of SK_MEMINFO_VARS via socket option. This way an
application can get all meminfo related information in single socket
option call instead of multiple calls.

Adds helper function, sk_get_meminfo(), and uses that for both
getsockopt and sock_diag_put_meminfo().

Suggested by Eric Dumazet.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Reviewed-by: Jason Baron <jbaron@akamai.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The arguments packets and bytes to call mlxsw_sp_acl_rule_get_stats are
in the wrong order. Fix this by swapping them.

Detected by CoverityScan, CID#1419705 ("Arguments in wrong order")

Fixes: 7c1b8eb1 ("mlxsw: spectrum: Add support for TC flower offload statistics")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are using the smallest padding boundary (8 bytes), which isn't
smaller than the Memory Controller Read/Write Size

We get best performance in 100G when the Packing Boundary is a multiple
of the Maximum Payload Size. Its related to inefficient chopping of DMA
packets by PCIe, that causes more overhead on bus. So driver is helping
by making the starting address alignment to be MPS size.

We will try to determine PCIE MaxPayloadSize capabiltiy  and set
IngPackBoundary based on this value. If cache line size is greater than
MPS or determinig MPS fails, we will use cache line size to determine
IngPackBoundary(as before).
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When building the driver as a module, we get a warning about the
lack of a license:

WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/synopsys/dwc-xlgmac.o
see include/linux/module.h for more information

Curiously the text in the .c files only mentions GPLv2+, while the license
tag in the PCI driver contains both GPL and BSD. I picked the license text
as the more definite reference here and put a GPL tag in there.

Fixes: 65e0ace2 ("net: dwc-xlgmac: Initial driver for DesignWare Enterprise Ethernet")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this header, we can run into a build error:

drivers/net/ethernet/synopsys/dwc-xlgmac-hw.c: In function 'xlgmac_config_queue_mapping':
drivers/net/ethernet/synopsys/dwc-xlgmac-hw.c:1548:36: error: 'IEEE_8021QAZ_MAX_TCS' undeclared (first use in this function)
  prio_queues = min_t(unsigned int, IEEE_8021QAZ_MAX_TCS,

Fixes: 65e0ace2 ("net: dwc-xlgmac: Initial driver for DesignWare Enterprise Ethernet")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jie Deng <jiedeng@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

neigh notifications today carry pid 0 for nlmsg_pid
in all cases. This patch fixes it to carry calling process
pid when available. Applications (eg. quagga) rely on
nlmsg_pid to ignore notifications generated by their own
netlink operations. This patch follows the routing subsystem
which already sets this correctly.
Reported-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2017-03-21

This series contains updates to e1000, e1000e, igb, igbvf and ixgb.

This finishes up the work Philippe Reynes did to update the Intel drivers
to the new API for ethtool (get|set)_link_ksettings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed: IOV related clenaups

This patch series targets IOV functionality [on both PF and VF].

Patches #2, #3 and #5 fix flows relating to malicious VFs, either by
upgrading and aligning current safe-guards or by correcing racy flows.

Patches #1 and #8 make some malicious/dysnfunctional VFs logging appear
by default in logs.

The rest of the patches either cleanup the existing code or else correct
some possible [yet fairly insignicant] issues in VF behavior.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The link information exists only on the leading hwfn,
but some of its derivatives [e.g., min/max rate] need to
be configured for each hwfn.
When re-basing the VF link view, use the leading hwfn
information as basis for all existing hwfns to allow
said configurations to stick.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Malicious VF existance should be interesting enough for the
hyperuser. Change the PF indication that one of its child VF
became malicious to appear by default.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PF<->VF interface allows for the VF to request
multiple queues closure via a single message, but this has
never been used by any official driver.

We now deprecate this option, forcing each queue close
to arrive via a different command; This would be required
for future TLVs that are going to extend the queue TLVs with
additional information on a per-queue basis.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PF needs to validate the status of VF queues before asking firmware
to configure anything for them, but that validation is done in various
different forms - sometimes inadequate.

Add auxillary functions that can be used for testing of the queue
state and convert the various flows to use those instead of current
existing flows; Also, add missing validations where needed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When starting the VF's vport, the PF would first configure
the status blocks of the VF and then reset them.
That would cause some of the configured information to be lost -
specifically it would mean that all the VFs queues would use
the Rx coalescing state-machine of the status block.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When PF responds to the VF requests it also cleans the HW-channel
indication in firmware to allow further VF messages to arrive,
but the order currently applied is wrong -
The PF is copying by DMAE the response the VF is polling on for
completion, and only afterwards sets the HW-channel to ready state.

This creates a race condition where the VF would be able to send
an additional message to the PF before the channel would get ready
again, causing the firmware to consider the VF as malicious.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a VF is considered malicious, driver handling of the VF
FLR flow would clean said indication - but not if the FLR is
part of an sriov-disable flow.
That leads to further issues, as PF wouldn't re-enable the
previously malicious VF when sriov is re-enabled.

No reason for that - simply clean malicious indications in
the sriov-disable flow as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VFs are currently logging errors when communicating
with their PFs in a too-low verbosity that wouldn't
be shown by default. As timeouts and failed commands
are crucial for VF operability, make them appear by
default.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add rhashtable_lookup_get_insert_fast for fixed keys, similar to
rhashtable_lookup_get_insert_key for explicit keys.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change to support host<->firmware command return value.
Fix for vf mac addr state command.
1. Added support for firmware commands to return a value:
   - previously, the returned code overlapped with host codes, thus
     commands were only returning 0 (success) or -1 (interpreted as
     timeout)
   - per 'response_manager.h', the error codes are split into two fields
     (major/minor) now, firmware commands are grouped into their own
     'major' group, separate from the host's 'major' group, which allow f/w
     commands to return any 16-bit value
2. The command to set vf mac addr was logging a success message even if
   command failed.  Now command uses a callback function to log the status
   message.
3. The command to set vf mac addr was not logging a message when set via
   the host 'ip' command.  Now, the callback function will log an
   appropriate message.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>