Signed-off-by: Steve French <sfrench@us.ibm.com>

Kconfig option for CIFS upcall.
Signed-off-by: Steve French <sfrench@us.ibm.com>

I just hit a page allocation error on a kernel configured to support
64 CPUs.  It spewed 60 completely useless unnecessary lines of info.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Website for DCCP is now hosted at OSDL
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is a first go at some documentation. Please advise if gmail
has mangled patch and I will revert to an attachment:
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The protocol field in ethernet headers is big-endian and should be
annotated as such.  This patch allows detection of missing ntohs() calls
on the ethernet protocol field when sparse is run with __CHECK_ENDIAN__
defined.

This is a revised version that includes <linux/types.h> so that the
userspace programs are not confused by __be16.  Thanks to David S.
Miller.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Here is the patch that introduces the generic skb_checksum_complete
which also checks for hardware RX checksum faults.  If that happens,
it'll call netdev_rx_csum_fault which currently prints out a stack
trace with the device name.  In future it can turn off RX checksum.

I've converted every spot under net/ that does RX checksum checks to
use skb_checksum_complete or __skb_checksum_complete with the
exceptions of:

* Those places where checksums are done bit by bit.  These will call
netdev_rx_csum_fault directly.

* The following have not been completely checked/converted:

ipmr
ip_vs
netfilter
dccp

This patch is based on patches and suggestions from Stephen Hemminger
and David S. Miller.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the superfluous parameter checking in bnx2_{get,set}_eeprom.
The parameters are already validated in ethtool_{get,set}_eeprom.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check return of dev_alloc_skb in bnx2_test_loopback, and handle
appropriately.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Output driver name as prefix to "Unknown flash/EEPROM type." message.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Chas Williams <cmas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>

I have to revert the recent addition of -imacros to the Makefile to get my
tool chain to build.  Without the change, below, I get:

Note that this looks entirely like a toolchain bug.  Here is the offending command:

[pid 12163] execve("/usr/lib/gcc-lib/i386-redhat-linux/3.2.2/tradcpp0", ["/usr/lib/gcc-lib/i386-redhat-linux/3.2.2/tradcpp0", "-lang-asm", "-nostdinc", "-Iinclude", "-Iinclude/asm-i386/mach-default", "-D__GNUC__=3", "-D__GNUC_MINOR__=2", "-D__GNUC_PATCHLEVEL__=2", "-D__GXX_ABI_VERSION=102", "-D__ELF__", "-Dunix", "-D__gnu_linux__", "-Dlinux", "-D__ELF__", "-D__unix__", "-D__gnu_linux__", "-D__linux__", "-D__unix", "-D__linux", "-Asystem=posix", "-D__NO_INLINE__", "-D__STDC_HOSTED__=1", "-Acpu=i386", "-Amachine=i386", "-Di386", "-D__i386", "-D__i386__", "-D__tune_i386__", "-D__KERNEL__", "-D__ASSEMBLY__", "-isystem", "/usr/lib/gcc-lib/i386-redhat-linux/3.2.2/include", "-imacros", "include/linux/autoconf.h", "-MD", "arch/i386/kernel/.entry.o.d", "arch/i386/kernel/entry.S", "-o", "/tmp/ccOlsFJR.s"]

Which should execute properly, I think.  But it does not:

zach-dev:linux-2.6.14-zach-work $ make
  CHK     include/linux/version.h
  CHK     include/linux/compile.h
  CHK     usr/initramfs_list
  AS      arch/i386/kernel/entry.o
/usr/lib/gcc-lib/i386-redhat-linux/3.2.2/tradcpp0: output filename specified twice
make[1]: *** [arch/i386/kernel/entry.o] Error 1
make: *** [arch/i386/kernel] Error 2

gcc (GCC) 3.2.2 20030222 (Red Hat Linux 3.2.2-5)

Deprecating the -imacros fixes the build for me.  It does not appear to be a
simple argument overflow problem in trapcpp0, since deprecating all the defines
reproduces the problem as well.  Also, switching -imacros to -include fixes the
problem.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>

Revert: b26b9bc5Signed-off-by: David S. Miller <davem@davemloft.net>

The previous umad deadlock fix left ib_umad_kill_port() still
vulnerable to deadlocking.  This patch fixes that by downgrading our
lock to a read lock when we might end up trying to reacquire the lock
for reading.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

In Tavor mode, when posting a long list of receive work requests, a
doorbell must be rung every 256 requests.  Add code to do this when
required.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Handle case where prod_index has wrapped around and become less than
cq->cons_index by checking that their difference as a signed int is
positive rather than comparing directly.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The size of work requests for atomic operations was computed
incorrectly in mthca: all sizeofs need to be divided by 16.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Move the computation of QP capabilities (max scatter/gather entries,
max inline data, etc) into the kernel, and have the uverbs module
return the values as part of the create QP response.  This keeps
precise knowledge of device limits in the low-level kernel driver.

This requires an ABI bump, so while we're making changes, get rid of
the max_sge parameter for the modify SRQ command -- it's not used and
shouldn't be there.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Now that ib_umad uses the new MAD sending interface, it no longer
needs its own L_Key.  So just delete the array of MRs that it keeps.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Change the struct ib_device.resize_cq() method to take a plain integer
that holds the new CQ size, rather than a pointer to an integer that
it uses to return the new size.  This makes the interface match the
exported ib_resize_cq() signature, and allows the low-level driver to
update the CQ size with proper locking if necessary.

No in-tree drivers are exporting this method yet.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Fix a typo in the rearming of the catastrophic error polling timer: we
should rearm the timer as long as the stop flag is _not_ set.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

For cut-and-paste reasons, the IPoIB driver was setting skb->dev right
before calling dev_kfree_skb_any().  Get rid of this.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

ib_unregister_mad_agent() completes all pending MAD sends and waits
for the agent's send_handler routine to return.  umad's send_handler()
calls queue_packet(), which does down_read() on the port mutex to look
up the agent ID.  This means that the port mutex cannot be held for
writing while calling ib_unregister_mad_agent(), or else it will
deadlock.  This patch fixes all the calls to ib_unregister_mad_agent()
in the umad module to avoid this deadlock.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Add ibX_path files to debugfs that contain information about the IPoIB
path cache.  IPoIB ARP only gives GIDs, which the IPoIB driver must
resolve to real IB paths through the ib_sa module.  For debugging,
when the ARP table looks OK but traffic isn't flowing, it's useful to
be able to see if the resolution from GID to path worked.

Also clean up the formatting of the existing _mcg debugfs files.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

If a task is being traced we never auto-reap it even if it might look
like its parent doesn't care. The tracer obviously _does_ care.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Patch from Liam Girdwood

This patch allows users of the pxa SSP driver to register their own irq
handlers instead of using the default SSP handler. It also cleans up the
CKEN clock and irq detection as the values are now stored in a table.

This patch replaces 2845/1

Changes:-
o Added flags parameter to ssp_init()
o Added SSP_NO_IRQ flag to disable registering of ssp irq handler (for
drivers that want to register their own handler)
o Cleaned up clock and irq detection, values are now stored in table.
o Added build changes to allow other drivers (e.g audio) to select the
ssp driver.
o corgi_ssp.c changed to use new interface.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Richard Purdie

This patch adds a power and battery management core driver which with
the addition of the right device files, supports the c7x0 and cxx00
series of Sharp Zaurus handhelds.

The driver is complex for several reasons. Battery charging is manually
monitored and controlled. When suspended, the device needs to
periodically partially resume, check the charging status and then
re-suspend. It does without bothering the higher linux layers as
a full resume and re-suspend is unnecessary. The code is carefully
written to avoid interrupts or calling code outside the module under
these circumstances. It also vets the various wake up sources and
monitors the device's power situation.

Hooks to limit the backlight intensity and to notify the battery
monitoring code of backlight events are connected/added as the
backlight is one of the biggest users of power on the device.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch updates omap H2 defconfig.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch syncs the mainline kernel with linux-omap tree.

This patch contains changes to common header files for
omap1xxx and omap24xx by various omap developers, and
improved cpu detection by Imre Deak
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch adds omap24xx specific clock code by
Richard Woodruff, Nishant Menon, Tony Lindgren et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch adds support for omap24xx series of processors.
The files live in arch/arm/mach-omap2, and share common
files with omap15xx and omap16xx processors in
arch/arm/plat-omap.

Omap24xx support was originally added for 2.6.9 by TI.
This code was then improved and integrated to share common
code with omap15xx and omap16xx processors by various
omap developers, such as Paul Mundt, Juha Yrjola, Imre Deak,
Tony Lindgren, Richard Woodruff, Nishant Menon, Komal Shah
et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:

- Serial port and framebuffer init improvments by Imre Deak

- Common omap pin mux framework by Tony Lindgren

- Common omap clock framework by Tony Lindren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:

- Omap1 serial pport and framebuffer init updates by Imre Deak

- Add support for omap310 processor and Palm Tungsten E PDA
  by Laurent Gonzales, Romain Goyet, et al. Omap310 and
  omap1510 processors are now handled as omap15xx.

- Omap1 specific changes to shared omap clock framework
  by Tony Lindgren

- Omap1 specific changes to shared omap pin mux framework
  by Tony Lindgren

- Other misc fixes, such as update memory timings for smc91x,
  omap1 specific device initialization etc.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>