- 04 Nov, 2009 1 commit
-
-
John W. Linville authored
wl1271_main.c:(.text+0x271052): undefined reference to `unregister_inetaddr_notifier' wl1271_main.c:(.text+0x2714d7): undefined reference to `register_inetaddr_notifier' Driver is doing some filtering based on IP addresses... Acked-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 02 Nov, 2009 29 commits
-
-
Juuso Oikarinen authored
Responses to firmware commands are read in by the command transmission function, as part of command flow. Previously responses were read in multiple places. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
Correct the endianness-handling of the firmware command result status handling code. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
PSM entries can fail (transmitting the corresponding null-func may not be heard by the AP.) Previously, this scenario was not detected, and out-of-sync between STA and AP could occur. Add retry implementation for the entries to recover from the situation. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
Check the result code of all commands, and return an error code if the firmware reports an error in execution. Previously this error would go ignored in most cases. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
Currently, to avoid distortions, the TX power level has been hardcoded to a low value. The value is slightly too low for good functionality, so we increase it from 7dB to 12dB. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
The null-data template (nullfunc) is dependent on the BSSID of the current AP only, so it needs to be updated only when the BSSID changes. Removed excess setting of the template. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Currently it is possible to request a scan on only disabled channels, which could be problematic for some drivers. Reject such scans, and also ignore disabled channels that are given. This resuls in the scan begin/end event only including channels that are actually used. This makes the mac80211 check for disabled channels superfluous. At the same time, remove the no-IBSS check from mac80211 -- nothing says that we should not find any networks on channels that cannot be used for an IBSS, even when operating in IBSS mode. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
Report successful transmissions (receiver awake and on the same channel) by generating ACK frames on the hwsim0 interface. This makes it easier to figure out from packet capture logs whether frames were delivered or not. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
Track the idle state for hwsim radios and reject TX if mac80211 is trying to transmit something when the radio is supposed to be idle. In addition, do not deliver frames if the receiving radio is in the idle state. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
Neither of these commands should clear the current configuration value if they return error. Furthermore, cfg80211_set_cipher_group() should be able to handle IW_AUTH_CIPHER_NONE without reporting error. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Christian Lamparter authored
James Grossmann [1] reported that p54 spews out confusing messages instead of preventing the mayhem from happening. the reason is that "p54: generate channel list dynamically" is not perfect. It didn't discard incomplete channel data sets and therefore p54 advertised to support them as well. [1]: http://marc.info/?l=linux-wireless&m=125699830215890 Cc: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: James Grossmann <cctsurf@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Since sometimes mac80211 queues up a scan request to only act on it later, it must be allowed to (internally) cancel a not-yet-running scan, e.g. when the interface is taken down. This condition was missing since we always checked only the local->scanning variable which isn't yet set in that situation. Reported-by: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
For 6x50 series, it is wimax/wifi combo device, so driver need to enable the wimax/wifi co-exist function and send the coexist event priority table to uCode for operation. The priority table will be used by uCode to determine what is the proper action it should take when co-exist with WiMAX. For example, when WiFi runs a scan, it must own radio exclusively, therefore will disconnect WiMAX if WiMAX is connected. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
Spatial Multiplexing Power Save was disabled to achieve better throughput while in power save mode by activating all the rx chains all the time. By doing so, the device power consumption is high. Enable static/dynamic spatial multiplexing power save if device support it, which can lower the power consumption without impact throughput. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
Add data structure define for COEX_MEDIUM_NOTIFICATION and COEX_EVENT_CMD host commands. COEX_MEDIUM_NOTIFICATION is notification from uCode to host to indicate medium changes. COEX_EVENT_CMD is from host to uCode for coex event request. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Reinette Chatre authored
More information than the "-EIO" return code will be useful here. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Reinette Chatre authored
This fits better in how the callbacks operate (alloc does allocation and init does initialization). This also helps if we later want to do our own initialization without relying on the mac80211 allocation. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Reinette Chatre authored
Currently the rate scale information is pointed to from the mac80211 station structure but since that is the only member we might as well make it part of the structure. Also move the rate scaling initialization to the init function, no need to do it when we allocate the structure. This fits with how mac80211 deals with rate scaling information (it always calls init after allocation) and makes it easier for us to later call initialization directly. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Reinette Chatre authored
In preparation for some station management changes we split the addition of a broadcast station from the other stations. Later we will rely on mac80211 to direct all management (addition/removal) of all stations except the broadcast station. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Reinette Chatre authored
Since iwlagn is the only user of these functions, move it to this module. This results in a bit more code moving than just these functions since the functions only used by them are also moved and we need to export the symbols previously available to them directly. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Reinette Chatre authored
Handling responses to driver originated commands include passing the original command buffer to the caller. At this time it is possible for a callback to be invoked that is passed this command buffer and thus likely to access it. We need to make sure that the memory associated with that buffer is not DMA mapped at the time. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Cahill authored
Wakeup interrupt has been updating write pointers (indexes, actually) only for tx queues 0-5. This is adequate just for 3945, but inadequate for other devices, all of which have more tx queues. Now updating all tx/command queues, so device can be aware of all new tx and host commands enqueued while device was asleep. This can potentially improve data traffic bandwidth and/or latency. Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Cahill authored
Add/clarify comments and debug messages for interrupt used only for uCode load Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Cahill authored
Invoke workaround to avoid instability in L0->L0S->L1 transition on PCIe bus. Workaround disables L0S state so device moves directly from L0->L1. Workaround needed on all devices since and including 4965; add to 6000/1000. Describe bug and workaround better in comments. Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Cahill authored
To save power, don't run apm_ops.init() until needed at "up" time. EEPROM (5000 and earlier devices) may be read without running apm_ops.init(), but OTP reads (6000 and newer devices) require a powered-up chip. Therefore, remove apm_ops.init() from the general path in XXXX_pci_probe(), and call it only if device uses OTP. Once done with OTP read, call apm_ops.stop() to reset chip and save power until "up" time comes around. NOTE: This patch depends on removal of priv->lock from iwl_apm_stop(); lock does not get initialized until later in flow. See patch "remove unneeded locks from apm_stop()". Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Cahill authored
Since priv->reg_lock was added to keep multi-access register manipulation atomic, priv->lock protection is no longer needed. Remove this from iwl_apm_stop_master() and iwl_apm_stop(). Add warning of timeout when polling for busmaster disablement confirmation, and some comments. NOTE: This is needed to enable use of apm_ops.stop() within iwl_eeprom_init(); priv->lock does not get initialized until after this flow. See patch "remove power-wasting calls to apm_ops.init()" Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Reinette Chatre authored
By setting the firmware version in wiphy it is possible to obtain this information via ethtool. Some examples, # ethtool -i wlan1 driver: iwlagn version: 2.6.32-rc5-wl-56840-g26d8540 firmware-version: 228.57.2.23 bus-info: 0000:03:00.0 # ethtool -i wlan0 driver: iwl3945 version: 2.6.32-rc5-wl-56840-g26d8540 firmware-version: 15.28.2.8 bus-info: 0000:02:00.0 Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
The multi-line code in this macro wasn't wrapped in do {} while (0) so we cannot use it in an if() branch safely in the future -- fix that. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Andrey Yurovsky authored
This patch removes the internal command and data buffers that the GSPI driver maintained and instead relies on the Libertas core to synchronize access to the command and data ports as with the other interface drivers. This cleanup reduces the GSPI driver's memory footprint and should improve performance by removing the need to copy to these internal buffers. This also simplifies the bottom half of the interrupt handler. This is an incremental cleanup: after removing the redundant buffers, we can further improve the driver to use a threaded IRQ handler instead of maintaining its own thread. However I would like a few folks to test the buffer removal first and make sure that I'm not introducing regressions. Tested on Blackfin BF527 with DMA disabled due to an issue with the SPI host controller driver in the current bleeding-edge Blackfin kernel. I would appreciate it if someone with working DMA could test this patch and provide feedback. Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Tested-by: George Shore <george.shore@imgtec.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 30 Oct, 2009 10 commits
-
-
Larry Finger authored
This patch is adapted from the submission by Michael Buesch <mb@bu3sch.de> for a bounce-buffer copying problem with b43. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
It's not right to do something here when returning an error, and hostapd should never have relied on it as it only fixes up a small part of the problem anyway. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
This variable is set once, and tested once. However, the code path that can set it is mutually exclusive with the code path that tests it, so the test is always true. Thus we also don't need to set it either and can just remove the variable. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
We drop nullfunc frames, but not qos-nullfunc frames, even though those could be used for PS state control as well. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luciano Coelho authored
The check after the loop which checks whether the initialization timed-out was wrong. If the initialization would succeed exactly in the 20000th time (the value set for INIT_LOOP), the driver would bail out and claim that initialization failed. Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
When mac80211 is asked to buffer multicast frames in AP mode, it will not set the flag indicating that the frames should be sent after the DTIM beacon for those frames buffered in software. Fix this little inconsistency by always setting that flag in the buffering code path. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
This value is unused by mac80211, because it was only be used by wireless extensions, and turned out to not be useful there because the quality value needs to be comparable between scan results and the current value which is impossible when the qual value is calculated taking into account noise, for example. Since it is unused anyway, this patch deprecates it in the hope that drivers will remove their sometimes quite expensive calculations of the value. I'm open to actual uses of the value, but the best way of using it seems to be what the Intel drivers do which should probably be generalised if we have noise values from the hardware. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Compared to ieee80211_beacon_get(), the new function ieee80211_beacon_get_tim() returns information on the location and length of the TIM IE, which some drivers need in order to generate the TIM on the device. The old function, ieee80211_beacon_get(), becomes a small static inline wrapper around the new one to not break all drivers. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Randy Dunlap authored
airo_cs uses spy interfaces so it needs to select WEXT_SPY. ERROR: "iw_handler_set_thrspy" [drivers/net/wireless/airo.ko] undefined! ERROR: "wireless_spy_update" [drivers/net/wireless/airo.ko] undefined! ERROR: "iw_handler_get_spy" [drivers/net/wireless/airo.ko] undefined! ERROR: "iw_handler_get_thrspy" [drivers/net/wireless/airo.ko] undefined! ERROR: "iw_handler_set_spy" [drivers/net/wireless/airo.ko] undefined! Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Zhu Yi authored
This fixed a BUG_ON in __skb_trim() when paged rx is used in iwlwifi driver. Yes, the whole mac80211 stack doesn't support paged SKB yet. But let's start the work slowly from small code snippets. Reported-and-tested-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-