Silvercrest mt9v011 sensor produces a 640x480 image. However,
previously, the code were getting only half of the lines and merging two
consecutive frames to "produce" a 640x480 image.

With the addition of progressive mode, now em28xx is working with a full
image. However, when the number of lines is bigger than 240, the
beginning of some odd lines are filled with blank.

After lots of testing, and physically checking the device for a Xtal, it
was noticed experimentally that mt9v011 is using em28xx XCLK as its
clock. Due to that, changing XCLK value changes the maximum speed of the
stream.

At the tests, it were possible to produce up to 32 fps, using a 30 MHz
XCLK. However, at that rate, the artifacts happen even at 320x240. Lower
values of XCLK produces artifacts only at 640x480.

At some values of xclk (for example XCLKK = 6 MHz, 640x480), it is
possible to see an invalid sucession of artifacts with this pattern:

.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

(where the dots represent the blanked pixels)

So, it seems that a waveform in the format of a ramp is interferring at
the image.

The cause of this interference is currently unknown. Some possibilities
are:
	- electrical interference (maybe this device is broken?);
	- some issue at mt9v011 programming;
	- some bug at em28xx chip.

So, for now, let's be conservative and use a value of XCLK that we know
for sure that it won't cause artifacts.

As I'm waiting for more of such devices with different em28xx chipset
revisions, I'll have the opportunity to double check the issue with
other pieces of hardware.

Later patches can vary XCLK depending on the vertical resolutions, if a
proper fix is not discovered.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

em28xx_pre_card_setup() is meant to contain board-specific initialization. Also,
as autodetection sometimes occur only after having i2c bus enabled, this
function may need to be called later.

Moving those setups to happen outside the function avoids calling it twice without
need and without duplicating output lines at dmesg.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

We don't know the xtal frequency of Silvercrest, but we need to have
some value in order to allow controlling the frame rate frequency. The
value is probably still wrong, since the manufacturer announces this
device as being capable of 30fps, but the maximum we can get is
13.5 fps.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Due to historical reasons, em28xx driver gets two consecutive frames and
fold them into an unique framing, doing interlacing. While this works
fine for TV images, this produces two bad effects with webcams:

1) webcam images are progressive. Merging two consecutive images produce
interlacing artifacts on the image;

2) since the driver needs to get two frames, it reduces the maximum
frame rate by two.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

As reported by hermann pitton <hermann-pitton@arcor.de>, some devices
has a different chip id for em2710 (likely the older ones):

em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0)
em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22)
em28xx #0: em28xx chip ID = 17
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Thanks to hermann pitton <hermann-pitton@arcor.de> for pointing this new
variation.
Tested-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

em28xx doesn't have temporal scaling. However, on webcams, sensors are
capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should
be passed to the sensor for it to properly set frame rate.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Implement g_parm/s_parm ioctls. Those are used to check the current
frame rate (in fps) and to set it to a value. In practice, there are
only 15 possible different speeds, due to chip limits.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

A user discovered that the Geniatech x8000 encountered a regression when
the xc3028 power management was introduced.  The xc3028 never recovers after
setting the powerdown register, which is probably because the xc3028 reset
GPIO is not properly configured.  Since I do not have access to the hardware
and thus cannot determine the correct GPIO configuration, just disable xc3028
power management on this board, which fixes the regression.

Thanks to user "ritec" for reporting the issue and testing the fix.

Cc: rictec <rictec@netcabo.pt>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The introduction of the zl10353 i2c gate control broke support for the
Geniatech board (which is not behind an i2 gate).  Add the needed parameter.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Remove the following build warning:

sms-cards.c: In function 'sms_board_event':
sms-cards.c:120: warning: unused variable 'board'

Thanks to Hans Verkuil for pointing this out.

The problem code has been #if 0'd for now, this will likely be
used again in the future, once the event interface is complete.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The iSight sends non-UVC status events through the interrupt endpoint. Those
invalid events are reported to the kernel log, resulting in a log flood.

Only log the events when the UVC_TRACE_STATUS flag is set.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Commit 50144aee broke the Samsung NC10
netbook webcam. Instead of applying the FIX_BANDWIDTH quirk to all ViMicro
devices, list the devices explicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The current GPIO configuration breaks all Hauppauge devices.

The code being removed affects Hauppauge devices only,
and is the cause of the breakage.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

MAINTAINERS |    8 ++++++++
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Moving BOOT fixes problem.
Signed-off-by: Nils Kassube <kassube@gmx.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Currently, the VIDIOC_S_STD ioctl just returns -EINVAL regardless of
the norm passed.  This patch sets cx23885_mpeg_template.tvnorms and
cx23885_mpeg_template.current_norm so that the VIDIOC_S_STD will work.

Thanks to Joseph Yasi for pointing this out, even though this particular
fix was already pushed into a development repository, merge priority of
this changeset has been escalated as a result of Joseph posting this
identical patch.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Joseph A. Yasi <joe.yasi@gmail.com>
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Current tip is broken and does not switch back to DVB-T correctly
Signed-off-by: Sohail Syyed <linuxtv@hubstar.net>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This device uses msp34xx and uses 2.048 MHz frequency for I2S
communication.

Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with
this device and proposing an approach for fixing the issue.
Tested-by: Angelo Cano <acano@fastmail.fm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Fixes stack corruption bug present in dump_regs function of zl10353 and
qt1010 drivers: the buffer buf was one byte smaller than required -
there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom
bytes per line and 1 byte for zero ending the string required, i.e. 53
bytes, but only 52 were provided.

The one byte missing in stack based buffer buf can cause stack
corruption possibly leading to kernel oops, as discovered originally
with af9015 driver (af9015: fix stack corruption bug).
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From
the revision history at the mt9v011 datasheet, it seems that the chip
version has changed from the first release of the chip.

Thanks-to hermann pitton <hermann-pitton@arcor.de> for pointing this to
me, on his tests with a Silvercrest webcam.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This mistakenly tested against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This mistakenly tests against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

mclk_get_divisor uses pcdev->soc_host.dev, make sure it is initialized.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Merge branch 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf_counter: Report the cloning task as parent on perf_counter_fork()
  perf_counter: Fix an ipi-deadlock
  perf: Rework/fix the whole read vs group stuff
  perf_counter: Fix swcounter context invariance
  perf report: Don't show unresolved DSOs and symbols when -S/-d is used
  perf tools: Add a general option to enable raw sample records
  perf tools: Add a per tracepoint counter attribute to get raw sample
  perf_counter: Provide hw_perf_counter_setup_online() APIs
  perf list: Fix large list output by using the pager
  perf_counter, x86: Fix/improve apic fallback
  perf record: Add missing -C option support for specifying profile cpu
  perf tools: Fix dso__new handle() to handle deleted DSOs
  perf tools: Fix fallback to cplus_demangle() when bfd_demangle() is not available
  perf report: Show the tid too in -D
  perf record: Fix .tid and .pid fill-in when synthesizing events
  perf_counter, x86: Fix generic cache events on P6-mobile CPUs
  perf_counter, x86: Fix lapic printk message

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  futex: Fix handling of bad requeue syscall pairing
  futex: Fix compat_futex to be same as futex for REQUEUE_PI
  locking, sched: Give waitqueue spinlocks their own lockdep classes
  futex: Update futex_q lock_ptr on requeue proxy lock

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Fix oops in identify_cpu() on CPUs without CPUID
  x86: Clear incorrectly forced X86_FEATURE_LAHF_LM flag
  x86, mce: therm_throt - change when we print messages
  x86: Add reboot quirk for every 5 series MacBook/Pro

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (22 commits)
  ocfs2: Fix possible deadlock when extending quota file
  ocfs2: keep index within status_map[]
  ocfs2: Initialize the cluster we're writing to in a non-sparse extend
  ocfs2: Remove redundant BUG_ON in __dlm_queue_ast()
  ocfs2/quota: Release lock for error in ocfs2_quota_write.
  ocfs2: Define credit counts for quota operations
  ocfs2: Remove syncjiff field from quota info
  ocfs2: Fix initialization of blockcheck stats
  ocfs2: Zero out padding of on disk dquot structure
  ocfs2: Initialize blocks allocated to local quota file
  ocfs2: Mark buffer uptodate before calling ocfs2_journal_access_dq()
  ocfs2: Make global quota files blocksize aligned
  ocfs2: Use ocfs2_rec_clusters in ocfs2_adjust_adjacent_records.
  ocfs2: Fix deadlock on umount
  ocfs2: Add extra credits and access the modified bh in update_edge_lengths.
  ocfs2: Fail ocfs2_get_block() immediately when a block needs allocation
  ocfs2: Fix error return in ocfs2_write_cluster()
  ocfs2: Fix compilation warning for fs/ocfs2/xattr.c
  ocfs2: Initialize count in aio_write before generic_write_checks
  ocfs2: log the actual return value of ocfs2_file_aio_write()
  ...

* 'for-linus' of git://neil.brown.name/md:
  md: allow upper limit for resync/reshape to be set when array is read-only
  md/raid5: Properly remove excess drives after shrinking a raid5/6
  md/raid5: make sure a reshape restarts at the correct address.
  md/raid5: allow new reshape modes to be restarted in the middle.
  md: never advance 'events' counter by more than 1.
  Remove deadlock potential in md_open

* 'sh/for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: fix i2c init order on ap325rxa V2
  sh: fix i2c init order on Migo-R V2
  sh: convert processor device setup functions to arch_initcall()

kernel_sendpage() does the proper default case handling for when the
socket doesn't have a native sendpage implementation.

Now, arguably this might be something that we could instead solve by
just specifying that all protocols should do it themselves at the
protocol level, but we really only care about the common protocols.
Does anybody really care about sendpage on something like Appletalk? Not
likely.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Julien TINNES <julien@cr0.org>
Acked-by: Tavis Ormandy <taviso@sdf.lonestar.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A bug in (9f498cc5: perf_counter: Full task tracing) makes
profiling multi-threaded apps it go belly up.

[ output as: (PID:TID):(PPID:PTID) ]

 # ./perf report -D | grep FORK
0x4b0 [0x18]: PERF_EVENT_FORK: (3237:3237):(3236:3236)
0xa10 [0x18]: PERF_EVENT_FORK: (3237:3238):(3236:3236)
0xa70 [0x18]: PERF_EVENT_FORK: (3237:3239):(3236:3236)
0xad0 [0x18]: PERF_EVENT_FORK: (3237:3240):(3236:3236)
0xb18 [0x18]: PERF_EVENT_FORK: (3237:3241):(3236:3236)

Shows us that the test (27d028de perf report: Update for the new
FORK/EXIT events) in builtin-report.c:

        /*
         * A thread clone will have the same PID for both
         * parent and child.
         */
        if (thread == parent)
                return 0;

Will clearly fail.

The problem is that perf_counter_fork() reports the actual
parent, instead of the cloning thread.

Fixing that (with the below patch), yields:

 # ./perf report -D | grep FORK
0x4c8 [0x18]: PERF_EVENT_FORK: (1590:1590):(1589:1589)
0xbd8 [0x18]: PERF_EVENT_FORK: (1590:1591):(1590:1590)
0xc80 [0x18]: PERF_EVENT_FORK: (1590:1592):(1590:1590)
0x3338 [0x18]: PERF_EVENT_FORK: (1590:1593):(1590:1590)
0x66b0 [0x18]: PERF_EVENT_FORK: (1590:1594):(1590:1590)

Which both makes more sense and doesn't confuse perf report
anymore.
Reported-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: paulus@samba.org
Cc: Anton Blanchard <anton@samba.org>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <1250172882.5241.62.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

perf_pending_counter() is called from IRQ context and will call
perf_counter_disable(), however perf_counter_disable() uses
smp_call_function_single() which doesn't fancy being used with
IRQs disabled due to IPI deadlocks.

Fix this by making it use the local __perf_counter_disable()
call and teaching the counter_sched_out() code about pending
disables as well.

This should cover the case where a counter migrates before the
pending queue gets processed.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey J Ashford <cjashfor@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
LKML-Reference: <20090813103655.244097721@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Replace PERF_SAMPLE_GROUP with PERF_SAMPLE_READ and introduce
PERF_FORMAT_GROUP to deal with group reads in a more generic
way.

This allows you to get group reads out of read() as well.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey J Ashford <cjashfor@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
LKML-Reference: <20090813103655.117411814@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

perf_swcounter_is_counting() uses a lock, which means we cannot
use swcounters from NMI or when holding that particular lock,
this is unintended.

The below removes the lock, this opens up race window, but not
worse than the swcounters already experience due to RCU
traversal of the context in perf_swcounter_ctx_event().

This also fixes the hard lockups while opening a lockdep
tracepoint counter.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
Cc: Corey J Ashford <cjashfor@us.ibm.com>
LKML-Reference: <1250149915.10001.66.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

We're interested in just those symbols/DSOs, so filter out the
unresolved ones.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20090812211957.GE3495@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

While we can enable the perf sample records per tracepoint
counter, we may also want to enable this option for every
tracepoint counters to open, so that we don't need to add a
:record flag for all of them.

Add the -R, --raw-samples options for this purpose.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1250152039-7284-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>