Multiple error condition require fw/rf reset, driver should check all
the possible errors as long as the error checking functions for the
devices are available.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

wifi/wimax co-exist command is part of _agn device configuration
sequence; move it to iwl-agn-ucode.c which is more appropriate place for the
function.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Return -EAGAIN when request tx power information and uCode is not ready;
so it will not confuse with tx power information not available.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

sensitivity calibration and chain noise calibration are not available
for all the devices; use .cfg to configure the availability of those
calibration functions
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Instead of checking device type for enable/disable continuous ucode
trace function; put it in .cfg for better control and more
flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Instead of checking device type for enable/disable tx power control,
move it to .cfg for better control and more flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

The iw_mode will always follow the only vif we
have, but using the vif directly seems easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

The "chain_tx_power" debugfs function is to display the tx power per
chain based. Name it "tx_power" is misleading.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

For the devices do not have power save support, remove the power save
control related debugfs files.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Port following patch to 3945.

"commit 90c4162ff59a3281b6d2f7206740be6217bd6758
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Wed Apr 7 00:21:36 2010 -0700
    iwlwifi: fix scan races"
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Rename the current 6000 series Gen2 devices to Gen2a.
Rename the ucode name prefix to iwlwifi-6000g2a.
Also corrected the device IDs for Gen2a series devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-dev.h

When we kick off a firmware loading process,
and then unbind from the pci device right
away, we get into trouble. Avoid that by
waiting for the firmware loading to finish
(whether successfully or not) before the
unbind in iwl_pci_remove.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

When CONFIG_NET is disabled, the attempt to build wext-priv.c
fails with:

net/wireless/wext-priv.c: In function 'ioctl_private_call':
net/wireless/wext-priv.c:207: error: implicit declaration of function 'call_commit_handler'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

s/X/x
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With a little bit of restructuring it isn't necessary to have special
cases in rt2x00queue_write_tx_descriptor for writing the descriptor
for beacons.
Simply split off the kicking of the TX queue to a separate function
with is only called for non-beacons.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

According to the Ralink vendor driver for rt2800 we don't need a full
TXD for a beacon but just a TXWI in front of the actual beacon.
Fix the rt2800pci and rt2800usb beaconing code accordingly.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Preparation to fix rt2800 beaconing.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All of the driver's kick_tx_queue callback functions treat the TX queue
for beacons in a special manner.
Clean this up by integrating the kicking of the beacon queue into the
write_beacon callback function, and let the generic code no longer call
the kick_tx_queue callback function when updating the beacon.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

RXWI processing is exactly the same for rt2800pci and rt2800usb, so
make it common code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

TXWI writing is exactly the same for rt2800pci and rt2800usb, so
make it common code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We should simply follow what the hardware told us it has done.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove unused RXD_DESC_SIZE define and remove duplicated RXWI definitions
from rt2800.h.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We should take the stripping of the IV into account for the txdesc->length
field.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There are several places that use > ARRAY_SIZE() instead of
>= ARRAY_SIZE().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I changed "> ATH9K_HTC_MAX_TID" to ">= ATH9K_HTC_MAX_TID" to avoid a
potential overflow.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is a stray null dereference.  We initialize "ista" properly later on.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This mutex_unlock() has been here from the initial commit, but as nearly
as I can tell, there isn't a reason for it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

From the original report:

"I had problems to get my rtl8185 PCI card running on Sparc64: I always
got an error about "No suitable DMA available" followed by an error
that no device could be detected. When comparing the rtl8180 driver to
others I noticed that others are mostly using DMA_BIT_MASK so I changed
the custom mask to DMA_BIT_MASK(32) which fixed my issue."
Reported-by: Tiziano Müller <tm@dev-zero.ch>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800 devices use a different enumeration to specify what IFS values should
be used on frame transmission compared to the other rt2x00 devices. Hence,
create a new enum called txop that contains the valid values.

Furthermore use the appropriate txop values as found in the ralink drivers:
- TXOP_BACKOFF for management frames
- TXOP_SIFS for subsequent fragments in a burst
- TXOP_HTTXOP for all data frames
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, we configure a 128ms hang over period for the PSM entry
(the firmware will remain active for 128ms after sending the null func for
PSM and getting an ack for it.) This is a huge power consumption issue, and
appears unnecessary. So, configure the value to 1 ms.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Incresed the timeout value for command complete event waiting from 100
ms to 750 ms. In some rare cases it can take about 600 ms before
complete event for join command is received. This is most propably
caused by the firmware being busy with scanning related activities.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch changes the way JOIN's are performed, and channel numbers updated.
The reason for this is that the firmware JOIN command clears WPA(2) key
material, and if done while associated to a WPA(2) secured AP, will render
the data-path unusable.

While the channel is not usually changed while associated (and currently we
could not even support something like that), after performing a scan operation
while associated, mac80211 will re-set the current channel to the driver. This
caused our problem.

Also, the mac80211 is assuming that the driver channel configuration remains
persistent over periods of IDLE. Therefore remove channel resetting to zero
from the unjoin function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reading single registers did not pay attention to data endianness. This patch
fix that.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch reads the HW PG version (along with a ROM-version, embedded in the
same value) from the wl1271 hardware and publishes the value in a sysfs -file.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Switch LED off/on when handling CONF_CHANGE_IDLE.
Not doing this would leave the radio LED on even
though the chip would be in full sleep mode.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Generated using the new shiny intivals-tool [1]:

initvals -w -f ar9003 > ar9003_initvals.h

The respective checksums are:

0x000000005a76829d        ar9300_2p0_radio_postamble
0x000000009d90cb74        ar9300Modes_lowest_ob_db_tx_gain_table_2p0
0x00000000e0bc2c84        ar9300Modes_fast_clock_2p0
0x00000000852fca34        ar9300_2p0_radio_core
0x0000000000000000        ar9300Common_rx_gain_table_merlin_2p0
0x0000000078658fb5        ar9300_2p0_mac_postamble
0x0000000023235333        ar9300_2p0_soc_postamble
0x0000000054d41904        ar9200_merlin_2p0_radio_core
0x00000000618455d4        ar9300_2p0_baseband_postamble
0x000000009aa590a4        ar9300_2p0_baseband_core
0x000000004783d946        ar9300Modes_high_power_tx_gain_table_2p0
0x000000006681db44        ar9300Modes_high_ob_db_tx_gain_table_2p0
0x000000001f318700        ar9300Common_rx_gain_table_2p0
0x000000009990cb74        ar9300Modes_low_ob_db_tx_gain_table_2p0
0x00000000c9d66d40        ar9300_2p0_mac_core
0x0000000039139500        ar9300Common_wo_xlna_rx_gain_table_2p0
0x00000000a0c54980        ar9300_2p0_soc_preamble
0x00000000292e2544        ar9300PciePhy_pll_on_clkreq_disable_L1_2p0
0x000000002d3e2544        ar9300PciePhy_clkreq_enable_L1_2p0
0x00000000293e2544        ar9300PciePhy_clkreq_disable_L1_2p0

[1] http://wireless.kernel.org/en/users/Drivers/ath9k_hw/initvals-tool

Cc: Tom Hammel <thammel@atheros.com>
Cc: Enis Akay <Enis.Akay@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_common (used by ath9k and ath9k_htc) trusts the frames
blessed by hardware as OK are infact correct even if the rate
seen by the driver is unrecognized. ath9k_common just treats
these frames in mac80211 as frames as frames under 1 mbps rate.
It seems this might not be the best thing to do as other parts of
the frame might not be valid so just drop these frames for now.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This has no real functional change, this just moves the setting the
the mac80211 rate index into ath9k_process_rate(). This allows us
to eventually make ath9k_process_rate() return a negative value
in case we have detected a specific case rate situation which should
have been ignored.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>