Put the CHECK_EMERGENCY_SYNC back into the kupdate function.  I seem to
keep removing it.

Updated forward-port of Aodrea's O_DIRECT open() checks.  If the user
asked for O_DIRECT and the inode has no mapping or no a_ops then fail
the open up-front.

A patch from Rik which adds some operational statitics to the VM.

In /proc/meminfo:

PageTables:	Amount of memory used for process pagetables
PteChainTot:	Amount of memory allocated for pte_chain objects
PteChainUsed:	Amount of memory currently in use for pte chains.

In /proc/stat:

pageallocs:	Number of pages allocated in the page allocator
pagefrees:	Number of pages returned to the page allocator

		(These can be used to measure the allocation rate)

pageactiv:	Number of pages activated (moved to the active list)
pagedeact:	Number of pages deactivated (moved to the inactive list)
pagefault:	Total pagefaults
majorfault:	Major pagefaults
pagescan:	Number of pages which shrink_cache looked at
pagesteal:	Number of pages which shrink_cache freed
pageoutrun:	Number of calls to try_to_free_pages()
allocstall:	Number of calls to balance_classzone()


Rik will be writing a userspace app which interprets these things.

The /proc/meminfo stats are efficient, but the /proc/stat accumulators
will cause undesirable cacheline bouncing.  We need to break the disk
statistics out of struct kernel_stat and make everything else in there
per-cpu.  If that doesn't happen in time for 2.6 then we disable
KERNEL_STAT_INC().

Patch from David McCracken.  It is an optimisation to the rmap
pte_chains.

In the common case where a page is mapped by only a single pte, we
don't need to allocate a pte_chain structure.  Just make the page's
pte_chain pointer point straight at that pte and flag this with
PG_direct.

Fix to the page reclaim code from Rik.

Anonymous pages which have buffers arise when
truncate_complete_page()'s call to ->releasepage() failed.  Those pages
may still be mapped into process address spaces.

We should not remove them from the LRU, because that makes them
unswappable and they hang around until process exit.

This is the "minimal rmap" patch, writen by Rik, ported to 2.5 by Craig
Kulsea.

Basically,

before: When the page reclaim code decides that is has scanned too many
unreclaimable pages on the LRU it does a scan of process virtual
address spaces for pages to add to swapcache.  ptes pointing at the
page are unmapped as the scan proceeds.  When all ptes referring to a
page have been unmapped and it has been written to swap the page is
reclaimable.

after: When an anonymous page is encountered on the tail of the LRU we
use the rmap to see if it hasn't been referenced lately.  If so then
add it to swapcache.  When the page is again encountered on the LRU, if
it is still unreferenced then try to unmap all ptes which refer to it
in one hit, and if it is clean (ie: on swap) then free it.

The rest of the VM - list management, the classzone concept, etc
remains unchanged.

There are a number of things which the per-page pte chain could be
used for.  Bill Irwin has identified the following.


(1)  page replacement no longer goes around randomly unmapping things

(2)  referenced bits are more accurate because there aren't several ms
        or even seconds between find the multiple pte's mapping a page

(3)  reduces page replacement from O(total virtually mapped) to O(physical)

(4)  enables defragmentation of physical memory

(5)  enables cooperative offlining of memory for friendly guest instance
        behavior in UML and/or LPAR settings

(6)  demonstrable benefit in performance of swapping which is common in
        end-user interactive workstation workloads (I don't like the word
        "desktop"). c.f. Craig Kulesa's post wrt. swapping performance

(7)  evidence from 2.4-based rmap trees indicates approximate parity
        with mainline in kernel compiles with appropriate locking bits

(8)  partitioning of physical memory can reduce the complexity of page
        replacement searches by scanning only the "interesting" zones
        implemented and merged in 2.4-based rmap

(9)  partitioning of physical memory can increase the parallelism of page
        replacement searches by independently processing different zones
        implemented, but not merged in 2.4-based rmap

(10) the reverse mappings may be used for efficiently keeping pte cache
        attributes coherent

(11) they may be used for virtual cache invalidation (with changes)

(12) the reverse mappings enable proper RSS limit enforcement
        implemented and merged in 2.4-based rmap



The code adds a pointer to struct page, consumes additional storage for
the pte chains and adds computational expense to the page reclaim code
(I measured it at 3% additional load during streaming I/O).  The
benefits which we get back for all this are, I must say, theoretical
and unproven.  If it has real advantages (or, indeed, disadvantages)
then why has nobody demonstrated them?



There are a number of things remaining to be done:

1: Demonstrate the above advantages.

2: Make it work with pte-highmem  (Bill Irwin is signed up for this)

3: Don't add pte_chains to non-shared pages optimisation (Dave McCracken's
   patch does this)

4: Move the pte_chains into highmem too (Bill, I guess)

5: per-cpu pte_chain freelists (Rik?)

6: maybe GC the pte_chain backing pages. (Seems unavoidable.  Rik?)

7: multithread the page reclaim code.  (I have patches).

8: clustered add-to-swap.  Not sure if I buy this.  anon pages are
   often well-ordered-by-virtual-address on the LRU, so it "just
   works" for benchmarky loads.  But there may be some other loads...

9: Fix bad IO latency in page reclaim (I have lame patches)

10: Develop tuning tools, use them.

11: The nightly updatedb run is still evicting everything.

into home.transmeta.com:/home/torvalds/v2.5/linux

into home.transmeta.com:/home/torvalds/v2.5/linux

  Trivia time:

  - C99 conforming initializations by Rusty.

  - ide__sti() -> local_irq_enable() and its friends.

Most noticable in the patch:

1. we handle IRQ sharing now better then ever

2. survives quite a lot of testing by few people. Forexample
cat /dev/hdb > /dev/null, where /dev/hdb contains a CD-ROM
with a big cratch on the surface making sure it's broken :-).
it's BTW. amanzing how wide the cratch had to be until errors
ocurred.

3. Doesn't play with rq_rdev and friends

Fri Jul 12 05:04:32 CEST 2002 ide-clean-99

- Push nIEN disabling down at the place where we are finished with a particular
   request.

- First round of command line parser cleanups by Gerald Champagne.

- Unfold the drive eviction functions in do_request(). This allowed us to
   realize that we don't have to re-get the major/minor numbers of the device we
   are action on from the raw device field of the currently running request. One
   significant place less in kernel where major/minor data gets manipulated.

- Move the big IDE_BUSY loop out of do_request to do_ide_request().  This makes
   us realize that we don't have to clear the IDE_BUSY bit just before
   reentering do_request to look for more requests still pending on the queue
   and set it immediately again.

   This is fixing a tinny race on the code path from IRQ or timer function,
   where we had a tinny window between the clearing of the IDE_BUSY bit and
   reentering the request queue for completely unrelated requests to come in to
   our way.

- Don't return any value in do_reset1(). It's always ATA_OP_CONTINUES. Split it
   up in to two functions one for disks (well in fact channels) and one for
   ATAPI devices. It turns out that they can be moved to the places where they
   are used to clarify the code flow. The only function remaining is
   do_reset_channel() now.

- Duplicate code from ide_do_drive_code explicitely in ide_raw_taskfile().
   Simplify ide_raw_taskfile() thereafter. Realize that ide_do_drive_cmd()
   is now only used by ATAPI devices. Move it therefore to atapi.c.

- Do busy polling for ATAPI reset operations. This is much safer then the
   previous timer games played there. It simply doesn't make sense to give the
   bus up during such a subtile operation. We don't have to disable IRQs here as
   well, since we are already under the protection of the do_request mechanisms.
   (Well hopefully...)

- Remove no longer used reset_poll() function. poll_timeout and friends are now
   used only in pdc4030 code. Those function where not called from IRQ context
   but they where set as handlers and not as expiry functions.

- Return ATA_OP_CONTINUES instead of ATA_OP_FINISHED in ata_error(), to signal
   that we are willing to retry the operation until the maximal number of retry
   attempts is exceeded. Returning ATA_OP_FINISHED without prior end_request()
   hangs the system.

- Apply trivia from DJ patch set.

- Apply small configuration fix to ide-pci.c from Muli Ben-Yehuda.

- Feed add_blkdev_randomness with information we already have in struct
   ata_channel *ch->major, instead of using the major(macro) on the request in
   question.

- Make ide_raw_taskfile use the same request submission mechanism as
   tcq_invalidate_queue(). Something similar would be ideal for ioctl() code as
   well.

- Implement actual device reset. Realize that the recalibration procedure is
   doomed by the standard. Don't try to recover by recalibrating devices
   therefore -just our retry mechanism should work in those cases. And suddenly
   the error handling code is IRQ safe.

- Reinvent the ATA reset operation, since it is apparently needed. We still
   have to do the whole transfer timing reconfiguration there.

- Move drive_is_ready(), which is in reality an attempt to check for IRQ
   requesters without clearing the IRQ line, over to the place where it belongs:
   device.c, which is the direct device access abstraction place.  Rename it to
   ata_status_irq() to prevent global name space pollution.

- Updates to the pdc202xxx host chip controller setup code by Bart³omiej
   ¯o³nierkiewicz:

   Forward port 2.4 patch by Hank Yang from Promise:

	- Add PDC20271 support
	- Disable LBA48 support on PDC20262
	- Fix ATAPI UDMA port value
	- Add new quirk drive
	- Adjust timings for all drives when using ATA133
	- Update pdc202xx_reset() waiting time

- Mark TCQ as dangerous and add some bits about it to the help.

- Add some missing exports.

- Some small ide-scsi.c host allocation fixes by sullivan.

Get rid of dev in rdev and use bdev exclusively.

There is an awkwardness here in that userspace sometimes
passed down a dev_t (e.g. hot_add_disk) and sometime
a major and a minor (e.g. add_new_disk).  Should we convert
both to kdev_t as the uniform standard....
That is what was being done but it seemed very clumsy and
things were gets converted back and forth a lot.

As bdget used a dev_t, I felt safe in staying with dev_t once I
had one rather than converting to kdev_t and back.

Change partition_name calls to bdev_partition_name were possible.

All part of decreasing reliance on device numbers... atleast in
appearance.

Remove the sb from the mddev

Now that al the important information is in mddev, we don't need
to have an sb off the mddev.  We only keep the per-device ones.

Previously we determined if "set_array_info" had been run byb checking
mddev->sb.  Now we check mddev->raid_disks on the assumption that
any valid array MUST have a non-zero number of devices.

Remove dependance on superblock

All the remaining field of interest in the superblock
get duplicated in the mddev struture and this is treated as
authoritative.  The superblock gets completely generated at
write time, and all useful information extracted at read time.

This means that we can slot in different superblock formats
without affecting the bulk of the code.

Move persistent from superblock to mddev

Tidyup calc_dev_sboffset and calc_dev_size on the way

Remove number and raid_disk from personality arrays

These are redundant.  number not needed any more
raid_disk never was as that is the index.

nr_disks is gone from multipath/raid1

Never used.

Remove old_dev field.

We used to monitor the pervious device number of a
component device for superblock maintenance.  This is
not needed any more.

Don't maintain disc status in superblock.

The state is now in rdev so we don't maintain it
in superblock any more.
We also nolonger test content of superblock for
disk status
mddev->spare is now an rdev and not a superblock fragment.

when writing superblock, generate from mddev/rdev info.

Rather than relying on the superblock info being kept up-to-date,
we regenerate the superblock from mddev/rdev info before
each write.

Add "degraded" field to md device

This is used to determine if a spare should be added
without relying on the superblock.

Add in_sync flag to each rdev

This currently mirrors the MD_DISK_SYNC superblock flag,
but soon it will be authoritative and the superblock will
only be consulted at start time.

Add raid_disk field to rdev

Also change find_rdev_nr to find based on position
in array (raid_disk) not position in superblock (number).

Improve handling of spares in md

- hot_remove_disk is given the raid_disk rather than descriptor number
  so that it can find the device in internal array directly, no search.
- spare_inactive now uses mddev->spare->raid_disk instead of
  mddev->spare->number so it can find the device directly without searching
- spare_write does not need number.  It can use mddev->spare->raid_disk as above.
- spare_active does not need &mddev->spare.  It finds the descriptor directly
  and fixes it without this pointer

Remove concept of 'spare' drive for multipath.

Multipath now treats all working devices as
active and does io to to first working one.

Set desc_nr more sanely.

Currently rdev->desc_nr is set in sync_sbs which is typcially
called just before writing out the superblocks, which is an
odd place to set it.
It is also called when a new disk is added (which is sane) and
when an old disc is imported ... which is quesitonable.

With this patch it is set when a new disk is added, and when
the superblocks are being analysed, which makes lots of sense.

MULTIPATH is particularly an issue here.  The old code tried
to figure the desc_nr for an rdev by matching device numbers in
the superblock.  This doesn't make a lot of sense as
device numbers can change.  Now MULTIPATH components
get sequential desc_nrs.

Move md_update_sb calls

When a change which requires a superblock update happens
at interrupt time, we currently set a flag (sb_dirty) and
wakeup to per-array thread (raid1/raid5d/multipathd) to
do the actual update.

This patch centralises this.  The sb_update is now done
by the mdrecoveryd thread.  As this is always woken up after
the error handler is called, we don't need the call to wakeup
the local thread any more.

With this, we don't need "md_update_sb" to lock the array
any more and only use __md_update_sb which is local to md.c
So we rename __md_update_sb back to md_update_sb and stop
exporting it.

Pass the correct bdev to md_error

After a call to generic_make_request, bio->bi_bdev can have changed
(e.g. by a re-mapped like raid0).  So we cannot trust it for reporting
the source of an error.  This patch takes care to find the correct
bdev.

Rdev list cleanups.

An "rdev" can be on three different lists.
 - the list of all rdevs
 - the list of pending rdevs
 - the list of rdevs for a given mddev

The first list is now only used to list "unused" devices in
/proc/mdstat, and only pending rdevs can be unused, so this list
isn't necessary.
An rdev cannot be both pending and in an mddev, so we know rdev will
only be on one list at at time.

This patch discards  the all_raid_disks list, and changes the
pending list to use "same_set" in the rdev.  It also changes
/proc/mdstat to iterate through pending devices, rather than through
all devices.

So now an rdev is only on one list, either the pending list
or the list of rdevs for a given mddev.  This means that
ITERATE_RDEV_GENERIC doesn't need to be told which field,
to walk down: there is ony one.

Get rid of find_rdev_all

find_rdev_all is now only used to check if a device is already
used in an md array.

We change lock_rdev so that it claims the bdev for
the specific rdev rather than for rdevs in general.
Now lock_rdev will check if the bdev is inuse by another array
or not, so the find_rdev_all check isn't needed and is removed,
along with find_rdev_all itself.

We also make sure that the error code from lock_rdev is
propagated up properly.

Use symbolic names for multipath (-4) and linear (-1)

Also, a variable called "level" was being used to store a
"level" and a "personality" number.  This is potentially
confusing, so it is now two variables.

Don't "analyze_sb" when creating new array.

When creating a new array (and we have an mddev->sb),
don't both to analyze the superblocks.  There is no point.
Also, these means we always allocate the array sb in
analyze_sbs, rather than conditionally.

Embed bio in mp_bh rather than separate allocation.

multipath currently allocates an mp_bh and a bio for each
request.  With this patch, the bio is made to be part of the
mp_bh so there is only one allocation, and it from a private
pool (the bio was allocated from a shared pool).

Also remove "remaining" and "cmd" from mp_bh which aren't used.
And remove spare (unused) from multipath_private_data.

Remove state field from multipath mp_bh structure.

The MPBH_Uptodate flag is set but never used,
The MPBH_SyncPhase flag was never used.
These a both legacy from the copying of raid1.c

MPBH_PreAlloc is no longer needed as due to use of
mempools, so the state field can go...

Get multipath to use mempool

... rather than maintaining it's own mempool

Remove dead consistancy checking code from multipath.

This "consistancy_check" is carried over from raid1 on which multipath
was based, and was not used in raid1 and has since been removed.  Now
it gets removed from multipath too.

Remove bdput calls from raid personalities.

Some of the md personalities currently hold a counted reference
on a bdev.  This is not necessary as the main md module will always
hold a counted reference in the rdev.
This patch removes the code to take and drop these unnecessary
references.

The appended patch fixes a typo in net/sunrpc/xprt.c: We want to
ensure that we play safe, and only increment the UDP congestion window
when we have successfully transmitted a full frame of data.

In addition, we should perhaps still 'slow start' the UDP congestion
code rather than assuming that we can immediately fire off 8
requests. IOW revert the value of RPC_INITCWND.

Here's one bugfix which might help to explain the GRANTED failure. The
bug has been there all along (so I'll probably want to send this to
Marcelo too).

The code in question in supposed to ensure that we don't wait on a
reply if the RPC call doesn't expect one. However, if the socket
transmission failed for some reason, we do actually want to loop and
try again...

This bug will hit the RPC call in nlmsvc_grant_blocked().

agpgart: added "-agp" to the .c files that are for specific hardware types, based on mailing list comments.