- 15 Sep, 2017 40 commits
-
-
Oliver Neukum authored
commit 003e817a upstream. During a stress test these mice kept dropping and reappearing in runlevel 1 as opposed to 5. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Benjamin Tissoires authored
commit 70b69cfb upstream. Based on a patch from: Nikolai Kondrashov <Nikolai.Kondrashov@redhat.com> Most of the tablets handled by hid-uclogic already use MULTI_INPUT. For the ones which are not quirked in usbhid/hidquirks, they have a custom report descriptor which contains only one report per HID interface. For those tablets HID_QUIRK_MULTI_INPUT is transparent. According to https://github.com/DIGImend/tablets, the only problematic tablet currently handled by hid-uclogic is the TWHA60 v3. This tablet presents different report descriptors from the ones currently quirked. This is not a problem per se, given that this tablet is not supported currently in this version (it needs the same command as a Huion to start forwarding events). Reviewed-by:
Nikolai Kondrashov <spbnick@gmail.com> Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
-
Milan Plzik authored
commit feb6faf1 upstream. Genius PenSketch M912 digitizer tablet sends incorrect report descriptor by default. This patch replaces it with a corrected one. Signed-off-by:
Milan Plzik <milan.plzik@gmail.com> Reviewed-by:
-
Wangzhao Cai authored
commit 30c6fd42 upstream. I am using a USB keyborad that give me "usb_submit_urb(ctrl) failed: -1" error when I plugin it. and I need to wait for 10s for this device to be ready. By adding this quirks, the usb keyborad is usable right after plugin Signed-off-by:
Wangzhao Cai <microcaicai@gmail.com> Signed-off-by:
-
Paolo Bonzini authored
commit bbaf0e2b upstream. native_safe_halt enables interrupts, and you just shouldn't call rcu_irq_enter() with interrupts enabled. Reorder the call with the following local_irq_disable() to respect the invariant. Reported-by:
Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Acked-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by:
Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Michael Ellerman authored
commit ba4a648f upstream. In commit 8c272261 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"), we switched to the generic implementation of cpu_to_node(), which uses a percpu variable to hold the NUMA node for each CPU. Unfortunately we neglected to notice that we use cpu_to_node() in the allocation of our percpu areas, leading to a chicken and egg problem. In practice what happens is when we are setting up the percpu areas, cpu_to_node() reports that all CPUs are on node 0, so we allocate all percpu areas on node 0. This is visible in the dmesg output, as all pcpu allocs being in group 0: pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07 pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15 pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23 pcpu-alloc: [0] 24 25 26 27 [0] 28 29 30 31 pcpu-alloc: [0] 32 33 34 35 [0] 36 37 38 39 pcpu-alloc: [0] 40 41 42 43 [0] 44 45 46 47 To fix it we need an early_cpu_to_node() which can run prior to percpu being setup. We already have the numa_cpu_lookup_table we can use, so just plumb it in. With the patch dmesg output shows two groups, 0 and 1: pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07 pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15 pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23 pcpu-alloc: [1] 24 25 26 27 [1] 28 29 30 31 pcpu-alloc: [1] 32 33 34 35 [1] 36 37 38 39 pcpu-alloc: [1] 40 41 42 43 [1] 44 45 46 47 We can also check the data_offset in the paca of various CPUs, with the fix we see: CPU 0: data_offset = 0x0ffe8b0000 CPU 24: data_offset = 0x1ffe5b0000 And we can see from dmesg that CPU 24 has an allocation on node 1: node 0: [mem 0x0000000000000000-0x0000000fffffffff] node 1: [mem 0x0000001000000000-0x0000001fffffffff] Fixes: 8c272261 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID") Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Reviewed-by:
Nicholas Piggin <npiggin@gmail.com> Signed-off-by:
-
Christophe JAILLET authored
commit 5ebb6dd3 upstream. We should ensure that 'plane_no' is '< vb->num_planes' as done in 'vb2_plane_cookie' just a few lines below. Fixes: e23ccc0a ("[media] v4l: add videobuf2 Video for Linux 2 driver framework") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Robert Jarzmik authored
commit cbf52a3e upstream. When the kernel is compiled with an "O=" argument, the object files are not in the source tree, but in the build tree. This patch fixes O= build by looking for object files in the build tree. Fixes: 923e02ec ("scripts/tags.sh: Support compiled source") Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Eric Dumazet authored
commit 77d4b1d3 upstream. Alexander reported various KASAN messages triggered in recent kernels The problem is that ping sockets should not use udp_poll() in the first place, and recent changes in UDP stack finally exposed this old bug. Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind") Fixes: 6d0bfe22 ("net: ipv6: Add IPv6 support to the ping socket.") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Sasha Levin <alexander.levin@verizon.com> Cc: Solar Designer <solar@openwall.com> Cc: Vasiliy Kulikov <segoon@openwall.com> Cc: Lorenzo Colitti <lorenzo@google.com> Acked-By:
Lorenzo Colitti <lorenzo@google.com> Tested-By:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
David S. Miller authored
commit e3e86b51 upstream. If ip6_find_1stfragopt() fails and we return an error we have to free up 'segs' because nobody else is going to. Fixes: 2423496a ("ipv6: Prevent overrun when parsing v6 header options") Reported-by:
-
Richard Narron authored
commit 239e250e upstream. This fixes a problem with reading files larger than 2GB from a UFS-2 file system: https://bugzilla.kernel.org/show_bug.cgi?id=195721 The incorrect UFS s_maxsize limit became a problem as of commit c2a9737f ("vfs,mm: fix a dead loop in truncate_inode_pages_range()") which started using s_maxbytes to avoid a page index overflow in do_generic_file_read(). That caused files to be truncated on UFS-2 file systems because the default maximum file size is 2GB (MAX_NON_LFS) and UFS didn't update it. Here I simply increase the default to a common value used by other file systems. Signed-off-by:
Richard Narron <comet.berkeley@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Will B <will.brokenbourgh2877@gmail.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Sean Young authored
commit 963761a0 upstream. A rc device can call ir_raw_event_handle() after rc_allocate_device(), but before rc_register_device() has completed. This is racey because rcdev->raw is set before rcdev->raw->thread has a valid value. Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Thomas Gleixner authored
commit ff86bf0c upstream. The alarmtimer code has another source of potentially rearming itself too fast. Interval timers with a very samll interval have a similar CPU hog effect as the previously fixed overflow issue. The reason is that alarmtimers do not implement the normal protection against this kind of problem which the other posix timer use: timer expires -> queue signal -> deliver signal -> rearm timer This scheme brings the rearming under scheduler control and prevents permanently firing timers which hog the CPU. Bringing this scheme to the alarm timer code is a major overhaul because it lacks all the necessary mechanisms completely. So for a quick fix limit the interval to one jiffie. This is not problematic in practice as alarmtimers are usually backed by an RTC for suspend which have 1 second resolution. It could be therefor argued that the resolution of this clock should be set to 1 second in general, but that's outside the scope of this fix. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kostya Serebryany <kcc@google.com> Cc: syzkaller <syzkaller@googlegroups.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Dmitry Vyukov <dvyukov@google.com> Link: http://lkml.kernel.org/r/20170530211655.896767100@linutronix.de [bwh: Backported to 3.16: - Use ktime_to_ns()/ktime_set() as ktime_t is not scalar - Adjust context] Signed-off-by:
-
Thomas Gleixner authored
commit f4781e76 upstream. Andrey reported a alartimer related RCU stall while fuzzing the kernel with syzkaller. The reason for this is an overflow in ktime_add() which brings the resulting time into negative space and causes immediate expiry of the timer. The following rearm with a small interval does not bring the timer back into positive space due to the same issue. This results in a permanent firing alarmtimer which hogs the CPU. Use ktime_add_safe() instead which detects the overflow and clamps the result to KTIME_SEC_MAX. Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
-
Julius Werner authored
commit 32829da5 upstream. A recent fix to /dev/mem prevents mappings from wrapping around the end of physical address space. However, the check was written in a way that also prevents a mapping reaching just up to the end of physical address space, which may be a valid use case (especially on 32-bit systems). This patch fixes it by checking the last mapped address (instead of the first address behind that) for overflow. Fixes: b299cde2 ("drivers: char: mem: Check for address space wraparound with mmap()") Reported-by:
Nico Huber <nico.h@gmx.de> Signed-off-by:
Julius Werner <jwerner@chromium.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Oleg Drokin authored
commit 0a33252e upstream. lov_getstripe() calls set_fs(KERNEL_DS) so that it can handle a struct lov_user_md pointer from user- or kernel-space. This changes the behavior of copy_from_user() on SPARC and may result in a misaligned access exception which in turn oopses the kernel. In fact the relevant argument to lov_getstripe() is never called with a kernel-space pointer and so changing the address limits is unnecessary and so we remove the calls to save, set, and restore the address limits. Signed-off-by:
John L. Hammond <john.hammond@intel.com> Reviewed-on: http://review.whamcloud.com/6150 Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3221Reviewed-by:
Andreas Dilger <andreas.dilger@intel.com> Reviewed-by:
Li Wei <wei.g.li@intel.com> Signed-off-by:
Oleg Drokin <green@linuxhacker.ru> Signed-off-by:
-
Yisheng Xie authored
commit 70feee0e upstream. Kefeng reported that when running the follow test, the mlock count in meminfo will increase permanently: [1] testcase linux:~ # cat test_mlockal grep Mlocked /proc/meminfo for j in `seq 0 10` do for i in `seq 4 15` do ./p_mlockall >> log & done sleep 0.2 done # wait some time to let mlock counter decrease and 5s may not enough sleep 5 grep Mlocked /proc/meminfo linux:~ # cat p_mlockall.c #include <sys/mman.h> #include <stdlib.h> #include <stdio.h> #define SPACE_LEN 4096 int main(int argc, char ** argv) { int ret; void *adr = malloc(SPACE_LEN); if (!adr) return -1; ret = mlockall(MCL_CURRENT | MCL_FUTURE); printf("mlcokall ret = %d\n", ret); ret = munlockall(); printf("munlcokall ret = %d\n", ret); free(adr); return 0; } In __munlock_pagevec() we should decrement NR_MLOCK for each page where we clear the PageMlocked flag. Commit 1ebb7cc6 ("mm: munlock: batch NR_MLOCK zone state updates") has introduced a bug where we don't decrement NR_MLOCK for pages where we clear the flag, but fail to isolate them from the lru list (e.g. when the pages are on some other cpu's percpu pagevec). Since PageMlocked stays cleared, the NR_MLOCK accounting gets permanently disrupted by this. Fix it by counting the number of page whose PageMlock flag is cleared. Fixes: 1ebb7cc6 (" mm: munlock: batch NR_MLOCK zone state updates") Link: http://lkml.kernel.org/r/1495678405-54569-1-git-send-email-xieyisheng1@huawei.comSigned-off-by:
Yisheng Xie <xieyisheng1@huawei.com> Reported-by:
Kefeng Wang <wangkefeng.wang@huawei.com> Tested-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Punit Agrawal authored
commit 30809f55 upstream. On failing to migrate a page, soft_offline_huge_page() performs the necessary update to the hugepage ref-count. But when !hugepage_migration_supported() , unmap_and_move_hugepage() also decrements the page ref-count for the hugepage. The combined behaviour leaves the ref-count in an inconsistent state. This leads to soft lockups when running the overcommitted hugepage test from mce-tests suite. Soft offlining pfn 0x83ed600 at process virtual address 0x400000000000 soft offline: 0x83ed600: migration failed 1, type 1fffc00000008008 (uptodate|head) INFO: rcu_preempt detected stalls on CPUs/tasks: Tasks blocked on level-0 rcu_node (CPUs 0-7): P2715 (detected by 7, t=5254 jiffies, g=963, c=962, q=321) thugetlb_overco R running task 0 2715 2685 0x00000008 Call trace: dump_backtrace+0x0/0x268 show_stack+0x24/0x30 sched_show_task+0x134/0x180 rcu_print_detail_task_stall_rnp+0x54/0x7c rcu_check_callbacks+0xa74/0xb08 update_process_times+0x34/0x60 tick_sched_handle.isra.7+0x38/0x70 tick_sched_timer+0x4c/0x98 __hrtimer_run_queues+0xc0/0x300 hrtimer_interrupt+0xac/0x228 arch_timer_handler_phys+0x3c/0x50 handle_percpu_devid_irq+0x8c/0x290 generic_handle_irq+0x34/0x50 __handle_domain_irq+0x68/0xc0 gic_handle_irq+0x5c/0xb0 Address this by changing the putback_active_hugepage() in soft_offline_huge_page() to putback_movable_pages(). This only triggers on systems that enable memory failure handling (ARCH_SUPPORTS_MEMORY_FAILURE) but not hugepage migration (!ARCH_ENABLE_HUGEPAGE_MIGRATION). I imagine this wasn't triggered as there aren't many systems running this configuration. [akpm@linux-foundation.org: remove dead comment, per Naoya] Link: http://lkml.kernel.org/r/20170525135146.32011-1-punit.agrawal@arm.comReported-by:
Manoj Iyer <manoj.iyer@canonical.com> Tested-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by:
Punit Agrawal <punit.agrawal@arm.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by:
-
Thomas Gleixner authored
commit 478fe303 upstream. memcg_propagate_slab_attrs() abuses the sysfs attribute file functions to propagate settings from the root kmem_cache to a newly created kmem_cache. It does that with: attr->show(root, buf); attr->store(new, buf, strlen(bug); Aside of being a lazy and absurd hackery this is broken because it does not check the return value of the show() function. Some of the show() functions return 0 w/o touching the buffer. That means in such a case the store function is called with the stale content of the previous show(). That causes nonsense like invoking kmem_cache_shrink() on a newly created kmem_cache. In the worst case it would cause handing in an uninitialized buffer. This should be rewritten proper by adding a propagate() callback to those slub_attributes which must be propagated and avoid that insane conversion to and from ASCII, but that's too large for a hot fix. Check at least the return value of the show() function, so calling store() with stale content is prevented. Steven said: "It can cause a deadlock with get_online_cpus() that has been uncovered by recent cpu hotplug and lockdep changes that Thomas and Peter have been doing. Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(cpu_hotplug.lock); lock(slab_mutex); lock(cpu_hotplug.lock); lock(slab_mutex); *** DEADLOCK ***" Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1705201244540.2255@nanosSigned-off-by:
Steven Rostedt <rostedt@goodmis.org> Acked-by:
David Rientjes <rientjes@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by:
-
Ben Hutchings authored
commit 6e80ac5c upstream. xfrm6_find_1stfragopt() may now return an error code and we must not treat it as a length. Fixes: 2423496a ("ipv6: Prevent overrun when parsing v6 header options") Signed-off-by:
Craig Gallek <kraig@google.com> Signed-off-by:
-
Thinh Nguyen authored
commit dc9217b6 upstream. f_mass_storage has a memorry barrier issue with the sleep and wake functions that can cause a deadlock. This results in intermittent hangs during MSC file transfer. The host will reset the device after receiving no response to resume the transfer. This issue is seen when dwc3 is processing 2 transfer-in-progress events at the same time, invoking completion handlers for CSW and CBW. Also this issue occurs depending on the system timing and latency. To increase the chance to hit this issue, you can force dwc3 driver to wait and process those 2 events at once by adding a small delay (~100us) in dwc3_check_event_buf() whenever the request is for CSW and read the event count again. Avoid debugging with printk and ftrace as extra delays and memory barrier will mask this issue. Scenario which can lead to failure: ----------------------------------- 1) The main thread sleeps and waits for the next command in get_next_command(). 2) bulk_in_complete() wakes up main thread for CSW. 3) bulk_out_complete() tries to wake up the running main thread for CBW. 4) thread_wakeup_needed is not loaded with correct value in sleep_thread(). 5) Main thread goes to sleep again. The pattern is shown below. Note the 2 critical variables. * common->thread_wakeup_needed * bh->state CPU 0 (sleep_thread) CPU 1 (wakeup_thread) ============================== =============================== bh->state = BH_STATE_FULL; smp_wmb(); thread_wakeup_needed = 0; thread_wakeup_needed = 1; smp_rmb(); if (bh->state != BH_STATE_FULL) sleep again ... As pointed out by Alan Stern, this is an R-pattern issue. The issue can be seen when there are two wakeups in quick succession. The thread_wakeup_needed can be overwritten in sleep_thread, and the read of the bh->state maybe reordered before the write to thread_wakeup_needed. This patch applies full memory barrier smp_mb() in both sleep_thread() and wakeup_thread() to ensure the order which the thread_wakeup_needed and bh->state are written and loaded. However, a better solution in the future would be to use wait_queue method that takes care of managing memory barrier between waker and waiter. Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Thinh Nguyen <thinhn@synopsys.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> [bwh: Backported to 3.16: adjust filename] Signed-off-by:
-
Mintz, Yuval authored
commit 3968d389 upstream. Apparently multi-cos isn't working for bnx2x quite some time - driver implements ndo_select_queue() to allow queue-selection for FCoE, but the regular L2 flow would cause it to modulo the fallback's result by the number of queues. The fallback would return a queue matching the needed tc [via __skb_tx_hash()], but since the modulo is by the number of TSS queues where number of TCs is not accounted, transmission would always be done by a queue configured into using TC0. Fixes: ada7c19e ("bnx2x: use XPS if possible for bnx2x_select_queue instead of pure hash") Signed-off-by:
Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by:
-
Jeff Mahoney authored
commit 896533a7 upstream. If we fail to add the space_info kobject, we'll leak the memory for the percpu counter. Fixes: 6ab0a202 (btrfs: publish allocation data in sysfs) Signed-off-by:
Jeff Mahoney <jeffm@suse.com> Reviewed-by:
Liu Bo <bo.li.liu@oracle.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
David Sterba authored
commit cc2b702c upstream. Variables start_idx and end_idx are supposed to hold a page index derived from the file offsets. The int type is not the right one though, offsets larger than 1 << 44 will get silently trimmed off the high bits. (1 << 44 is 16TiB) What can go wrong, if start is below the boundary and end gets trimmed: - if there's a page after start, we'll find it (radix_tree_gang_lookup_slot) - the final check "if (page->index <= end_idx)" will unexpectedly fail The function will return false, ie. "there's no page in the range", although there is at least one. btrfs_page_exists_in_range is used to prevent races in: * in hole punching, where we make sure there are not pages in the truncated range, otherwise we'll wait for them to finish and redo truncation, but we're going to replace the pages with holes anyway so the only problem is the intermediate state * lock_extent_direct: we want to make sure there are no pages before we lock and start DIO, to prevent stale data reads For practical occurence of the bug, there are several constaints. The file must be quite large, the affected range must cross the 16TiB boundary and the internal state of the file pages and pending operations must match. Also, we must not have started any ordered data in the range, otherwise we don't even reach the buggy function check. DIO locking tries hard in several places to avoid deadlocks with buffered IO and avoids waiting for ranges. The worst consequence seems to be stale data read. CC: Liu Bo <bo.li.liu@oracle.com> Fixes: fc4adbff ("btrfs: Drop EXTENT_UPTODATE check in hole punching and direct locking") Reviewed-by:
-
Michael Ellerman authored
commit 99acc9be upstream. If a process dumps core while it has SPU contexts active then we have code to also dump information about the SPU contexts. Unfortunately it's been broken for 3 1/2 years, and we didn't notice. In commit 7b1f4020 ("spufs: get rid of dump_emit() wrappers") the nread variable was removed and rc used instead. That means when the loop exits successfully, rc has the number of bytes read, but it's then used as the return value for the function, which should return 0 on success. So fix it by setting rc = 0 before returning in the success case. Fixes: 7b1f4020 ("spufs: get rid of dump_emit() wrappers") Signed-off-by:
Jeremy Kerr <jk@ozlabs.org> Signed-off-by:
-
Jiang Yi authored
commit 5e0cf5e6 upstream. There are three timing problems in the kthread usages of iscsi_target_mod: - np_thread of struct iscsi_np - rx_thread and tx_thread of struct iscsi_conn In iscsit_close_connection(), it calls send_sig(SIGINT, conn->tx_thread, 1); kthread_stop(conn->tx_thread); In conn->tx_thread, which is iscsi_target_tx_thread(), when it receive SIGINT the kthread will exit without checking the return value of kthread_should_stop(). So if iscsi_target_tx_thread() exit right between send_sig(SIGINT...) and kthread_stop(...), the kthread_stop() will try to stop an already stopped kthread. This is invalid according to the documentation of kthread_stop(). (Fix -ECONNRESET logout handling in iscsi_target_tx_thread and early iscsi_target_rx_thread failure case - nab) Signed-off-by:
Jiang Yi <jiangyilism@gmail.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Nicholas Bellinger authored
commit 25cdda95 upstream. This patch fixes a OOPs originally introduced by: commit bb048357 Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Sep 5 14:54:04 2013 -0700 iscsi-target: Add sk->sk_state_change to cleanup after TCP failure which would trigger a NULL pointer dereference when a TCP connection was closed asynchronously via iscsi_target_sk_state_change(), but only when the initial PDU processing in iscsi_target_do_login() from iscsi_np process context was blocked waiting for backend I/O to complete. To address this issue, this patch makes the following changes. First, it introduces some common helper functions used for checking socket closing state, checking login_flags, and atomically checking socket closing state + setting login_flags. Second, it introduces a LOGIN_FLAGS_INITIAL_PDU bit to know when a TCP connection has dropped via iscsi_target_sk_state_change(), but the initial PDU processing within iscsi_target_do_login() in iscsi_np context is still running. For this case, it sets LOGIN_FLAGS_CLOSED, but doesn't invoke schedule_delayed_work(). The original NULL pointer dereference case reported by MNC is now handled by iscsi_target_do_login() doing a iscsi_target_sk_check_close() before transitioning to FFP to determine when the socket has already closed, or iscsi_target_start_negotiation() if the login needs to exchange more PDUs (eg: iscsi_target_do_login returned 0) but the socket has closed. For both of these cases, the cleanup up of remaining connection resources will occur in iscsi_target_start_negotiation() from iscsi_np process context once the failure is detected. Finally, to handle to case where iscsi_target_sk_state_change() is called after the initial PDU procesing is complete, it now invokes conn->login_work -> iscsi_target_do_login_rx() to perform cleanup once existing iscsi_target_sk_check_close() checks detect connection failure. For this case, the cleanup of remaining connection resources will occur in iscsi_target_do_login_rx() from delayed workqueue process context once the failure is detected. Reported-by:
Mike Christie <mchristi@redhat.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Sagi Grimberg <sagi@grimberg.me> Cc: Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Bart Van Assche authored
commit 1efaa949 upstream. This patch avoids that smatch complains about inconsistent indentation in iscsi_target_start_negotiation(). Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Cc: Nicholas A. Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 8f0dfb3d upstream. There is a iscsi-target/tcp login race in LOGIN_FLAGS_READY state assignment that can result in frequent errors during iscsi discovery: "iSCSI Login negotiation failed." To address this bug, move the initial LOGIN_FLAGS_READY assignment ahead of iscsi_target_do_login() when handling the initial iscsi_target_start_negotiation() request PDU during connection login. As iscsi_target_do_login_rx() work_struct callback is clearing LOGIN_FLAGS_READ_ACTIVE after subsequent calls to iscsi_target_do_login(), the early sk_data_ready ahead of the first iscsi_target_do_login() expects LOGIN_FLAGS_READY to also be set for the initial login request PDU. As reported by Maged, this was first obsered using an MSFT initiator running across multiple VMWare host virtual machines with iscsi-target/tcp. Reported-by:
Maged Mokhtar <mmokhtar@binarykinetics.com> Tested-by:
-
Russell King authored
commit 898805e0 upstream. The Marvell driver incorrectly provides phydev->lp_advertising as the logical and of the link partner's advert and our advert. This is incorrect - this field is supposed to store the link parter's unmodified advertisment. This allows ethtool to report the correct link partner auto-negotiation status. Fixes: be937f1f ("Marvell PHY m88e1111 driver fix") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Jan Kara authored
commit 67a7d5f5 upstream. Currently, extent manipulation operations such as hole punch, range zeroing, or extent shifting do not record the fact that file data has changed and thus fdatasync(2) has a work to do. As a result if we crash e.g. after a punch hole and fdatasync, user can still possibly see the punched out data after journal replay. Test generic/392 fails due to these problems. Fix the problem by properly marking that file data has changed in these operations. Fixes: a4bb6b64Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> [bwh: Backported to 3.16: drop change in ext4_insert_range()] Signed-off-by:
-
Jan Kara authored
commit a056bdaa upstream. mpage_submit_page() can race with another process growing i_size and writing data via mmap to the written-back page. As mpage_submit_page() samples i_size too early, it may happen that ext4_bio_write_page() zeroes out too large tail of the page and thus corrupts user data. Fix the problem by sampling i_size only after the page has been write-protected in page tables by clear_page_dirty_for_io() call. Reported-by:
Michael Zimmer <michael@swarm64.com> Fixes: cb20d518Signed-off-by:
-
Uwe Kleine-König authored
commit 82533ad9 upstream. The function ax_init_dev (which is called only from the driver's .probe function) calls free_irq in the error path without having requested the irq in the first place. So drop the free_irq call in the error path. Fixes: 825a2ff1 ("AX88796 network driver") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Wei Wang authored
commit ba615f67 upstream. Fastopen API should be used to perform fastopen operations on the TCP socket. It does not make sense to use fastopen API to perform disconnect by calling it with AF_UNSPEC. The fastopen data path is also prone to race conditions and bugs when using with AF_UNSPEC. One issue reported and analyzed by Vegard Nossum is as follows: +++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Thread A: Thread B: ------------------------------------------------------------------------ sendto() - tcp_sendmsg() - sk_stream_memory_free() = 0 - goto wait_for_sndbuf - sk_stream_wait_memory() - sk_wait_event() // sleep | sendto(flags=MSG_FASTOPEN, dest_addr=AF_UNSPEC) | - tcp_sendmsg() | - tcp_sendmsg_fastopen() | - __inet_stream_connect() | - tcp_disconnect() //because of AF_UNSPEC | - tcp_transmit_skb()// send RST | - return 0; // no reconnect! | - sk_stream_wait_connect() | - sock_error() | - xchg(&sk->sk_err, 0) | - return -ECONNRESET - ... // wake up, see sk->sk_err == 0 - skb_entail() on TCP_CLOSE socket If the connection is reopened then we will send a brand new SYN packet after thread A has already queued a buffer. At this point I think the socket internal state (sequence numbers etc.) becomes messed up. When the new connection is closed, the FIN-ACK is rejected because the sequence number is outside the window. The other side tries to retransmit, but __tcp_retransmit_skb() calls tcp_trim_head() on an empty skb which corrupts the skb data length and hits a BUG() in copy_and_csum_bits(). +++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Hence, this patch adds a check for AF_UNSPEC in the fastopen data path and return EOPNOTSUPP to user if such case happens. Fixes: cf60af03 ("tcp: Fast Open client - sendmsg(MSG_FASTOPEN)") Reported-by:
Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
Wei Wang <weiwan@google.com> Signed-off-by:
-
Jan Kara authored
commit 5375023a upstream. XFS SEEK_HOLE implementation could miss a hole in an unwritten extent as can be seen by the following command: xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "pwrite 128k 8k" -c "seek -h 0" file wrote 57344/57344 bytes at offset 0 56 KiB, 14 ops; 0.0000 sec (49.312 MiB/sec and 12623.9856 ops/sec) wrote 8192/8192 bytes at offset 131072 8 KiB, 2 ops; 0.0000 sec (70.383 MiB/sec and 18018.0180 ops/sec) Whence Result HOLE 139264 Where we can see that hole at offset 56k was just ignored by SEEK_HOLE implementation. The bug is in xfs_find_get_desired_pgoff() which does not properly detect the case when pages are not contiguous. Fix the problem by properly detecting when found page has larger offset than expected. Fixes: d126d43fSigned-off-by:
Brian Foster <bfoster@redhat.com> Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Eryu Guan authored
commit 8affebe1 upstream. xfs_find_get_desired_pgoff() is used to search for offset of hole or data in page range [index, end] (both inclusive), and the max number of pages to search should be at least one, if end == index. Otherwise the only page is missed and no hole or data is found, which is not correct. When block size is smaller than page size, this can be demonstrated by preallocating a file with size smaller than page size and writing data to the last block. E.g. run this xfs_io command on a 1k block size XFS on x86_64 host. # xfs_io -fc "falloc 0 3k" -c "pwrite 2k 1k" \ -c "seek -d 0" /mnt/xfs/testfile wrote 1024/1024 bytes at offset 2048 1 KiB, 1 ops; 0.0000 sec (33.675 MiB/sec and 34482.7586 ops/sec) Whence Result DATA EOF Data at offset 2k was missed, and lseek(2) returned ENXIO. This is uncovered by generic/285 subtest 07 and 08 on ppc64 host, where pagesize is 64k. Because a recent change to generic/285 reduced the preallocated file size to smaller than 64k. Signed-off-by:
Eryu Guan <eguan@redhat.com> Reviewed-by:
-
Lyude authored
commit 3d18e337 upstream. We end up reading the interrupt register for HPD5, and then writing it to HPD6 which on systems without anything using HPD5 results in permanently disabling hotplug on one of the display outputs after the first time we acknowledge a hotplug interrupt from the GPU. This code is really bad. But for now, let's just fix this. I will hopefully have a large patch series to refactor all of this soon. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Lyude <lyude@redhat.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> [bwh: Backported to 3.16: drop the DC_HPD6_RX_INTERRUPT cases] Signed-off-by:
-
Alex Deucher authored
commit 58d7e3e4 upstream. Even if the vblank period would allow it, it still seems to be problematic on some cards. v2: fix logic inversion (Nils) bug: https://bugs.freedesktop.org/show_bug.cgi?id=96868Acked-by:
-
Andrew Lunn authored
commit f2899788 upstream. The 88m1101 has an errata when configuring autoneg. However, it was being applied to many other Marvell PHYs as well. Limit its scope to just the 88m1101. Fixes: 76884679 ("phylib: Add support for Marvell 88e1111S and 88e1145") Reported-by:
Daniel Walker <danielwa@cisco.com> Signed-off-by:
Harini Katakam <harinik@xilinx.com> Reviewed-by:
-
Johannes Thumshirn authored
commit ddff7ed4 upstream. When pci_enable_device() or pci_enable_device_mem() fail in qla2x00_probe_one() we bail out but do a call to pci_disable_device(). This causes the dev_WARN_ON() in pci_disable_device() to trigger, as the device wasn't enabled previously. So instead of taking the 'probe_out' error path we can directly return *iff* one of the pci_enable_device() calls fails. Additionally rename the 'probe_out' goto label's name to the more descriptive 'disable_device'. Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Fixes: e315cd28 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring") Reviewed-by:
Giridhar Malavali <giridhar.malavali@cavium.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
