- 23 Jan, 2008 10 commits
-
-
Tejun Heo authored
Implement protocol tests - ata_is_atapi(), ata_is_nodata(), ata_is_pio(), ata_is_dma(), ata_is_ncq() and ata_is_data() and use them to replace is_atapi_taskfile() and hard coded protocol tests. Signed-off-by:
Tejun Heo <htejun@gmail.com> Signed-off-by:
Jeff Garzik <jeff@garzik.org>
-
Tejun Heo authored
Area for DFLAGs which are cleared on INIT is full. Extend it by 8 bits. Signed-off-by:
-
Jeff Garzik authored
Signed-off-by:Jeff Garzik <jgarzik@redhat.com>
-
Tejun Heo authored
For intel ones, ahci unconditionally OR'd 0xf to PCS. This isn't correct for the following cases. * ich6/7m's which only implement P0 and P2 (0xf works fine tho) * ich8/9's which have six ports and needs 0x3f to enable all ports This patch updates PCS programming such that... * port_map determined by ahci_save_initial_config() is OR'd instead of 0xf * PCS is updated only if necessary (there are turned off enable bits) port_map is determined from PORTS_IMPL PCI register which is implemented as write or write-once register. If the register isn't programmed, ahci automatically generates it from number of ports, which is good enough for PCS programming. ICH6/7M are probably the only ones where non-contiguous enable bits are necessary && PORTS_IMPL isn't programmed properly but they're proven to work reliably with 0xf anyway. Signed-off-by:
-
Alan Cox authored
Lots of work needed to bring it up to scratch but it does work so you can now use the card. That makes it at least useful, especially as the other cardbus cards are usually INIC162x which aren't yet supported well. Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
-
Alan Cox authored
Jeff said he preferred that the SFF tf_load followed the spec and we documented that anyone who needed different overrode it, rather than it using the ->check_status methods. No driver relies on the current behaviour. Signed-off-by:
-
Alan Cox authored
I believe this version meets all Sergei's objections Correct the logic for when we issue a set features for transfer mode - If the device has IORDY and the controller has IORDY - set the mode - If the device has IORDY and the controller does not - turn IORDY off - If neither has IORDY do nothing Signed-off-by:
-
Shaohua Li authored
ACPI spec (ver 3.0a, p289) requires IDE power on/off executes ACPI _PSx methods. As recently most PATA drivers use libata, this patch adds _PSx method support in libata. ACPI spec doesn't mention if SATA requires the same _PSx method. Signed-off-by:
Shaohua Li <shaohua.li@intel.com> Acked-by:
Len Brown <len.brown@intel.com> Signed-off-by:
-
Alan Cox authored
Historically word 48 in the identify data was used to mean 32bit I/O was supported for VLB IDE etc. ATA8 reassigns this word to the Trusted Computing Group, where it is used for TCG features. This means that an ATA8 TCG drive is going to trigger 32bit I/O on some systems which will be funny. Anyway we need to sort this out ready for ATA8 so: - Reorder the ata.h header a bit so the ata_version function occurs early in it - Make dword_io check the ATA version - Add an ATA8 version checking TCG presence test While we are at it the current drafts have a flaw where it may not be possible to disable TCG features at boot (and opt out of the trusted model) as TCG intends because it relies on presence of a different optional feature (DCS). Handle this in software by refusing the TCG commands if libata.allow_tpm is not set. (We must make it possible as some environments such as proprietary VDR devices will doubtless want to use it to lock up content) Finally as with CPRM print a warning so that the user knows they may not be able to full access and use the device. Signed-off-by: -
Peter Schwenke authored
Add Toshiba Satellite R20 and Tecra M6 to broken suspend list. Matt Piermarini reported and provided the M6 patch. This is from OSDL bug 7780. Signed-off-by:
Peter Schwenke <peter@bluetoad.com.au> Cc: Matt Piermarini <mattpiermarini@yahoo.com> Acked-by:
-
- 22 Jan, 2008 24 commits
-
-
Jordan Crouse authored
When we set the MFGPT timer tick, there is a chance that we'll immediately assert an event. If for some reason the IRQ routing for this clock has been setup for some other purpose, then we could end up firing an interrupt into the SMM handler or worse. This rearranges the timer tick init function to initalize the handler before we set up the MFGPT clock to make sure that even if we get an event, it will go to the handler. Furthermore, in the handler we need to make sure that we clear the event, even if the timer isn't running. Signed-off-by:
Jordan Crouse <jordan.crouse@amd.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Acked-by:
Ingo Molnar <mingo@elte.hu> Tested-by:
Arnd Hannemann <hannemann@i4.informatik.rwth-aachen.de>
-
Johann Felix Soden authored
Fix typo in arch/powerpc/boot/flatdevtree_env.h. There is no Documentation/networking/ixgbe.txt. README.cycladesZ is now in Documentation/. wavelan.p.h is now in drivers/net/wireless/. HFS.txt is now Documentation/filesystems/hfs.txt. OSS-files are now in sound/oss/. Signed-off-by:
Johann Felix Soden <johfel@users.sourceforge.net> Acked-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://lm-sensors.org/kernel/mhoffman/hwmon-2.6Linus Torvalds authored
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: hwmon: (it87) request only Environment Controller ports
-
git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86: Revert "x86: fix NMI watchdog & 'stopped time' problem"
-
git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-schedLinus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched: sched: group scheduler, set uid share fix
-
Randy Dunlap authored
rcu_online_cpu() should be __cpuinit instead of __devinit. WARNING: vmlinux.o(.text+0x4b6d5): Section mismatch: reference to .init.text: (between 'rcu_cpu_notify' and 'wakeme_after_rcu') Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
David Fries authored
The extra rom[0] check is flagging valid temperatures as invalid when there is already a CRC data transmission check. w1_therm_read_bin() if (rom[8] == crc && rom[0]) verdict = 1; Requiring rom[0] to be non-zero will flag as invalid temperature conversions when the low byte is zero, specifically the temperatures 0C, 16C, 32C, 48C, -16C, -32C, and -48C. The CRC check is produced on the device for the previous 8 bytes and is required to ensure the data integrity in transmission. I don't see why the extra check for rom[0] being non-zero is in there. Evgeniy Polyakov didn't know either. Just for a check I unplugged the sensor, executed a temperature conversion, and read the results. The read was all ff's, which also failed the CRC, so it doesn't need to protect against a disconnected sensor. I have more extensive patches in the work, but these two trivial ones will do for today. I would like to hear from people who use the ds2490 USB to one wire dongle. 1 if you would be willing to test the patches as I currently only have the one sensor on a short parisite powered wire, 2 if there is any cheap sources for the ds2490. Signed-off-by:
David Fries <david@fries.net> Acked-by:
Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by:
-
David Fries authored
Correct the decoding of negative C temperatures. The code did a binary OR of two bytes to make a 16 bit value, but assignd it to an integer. This caused the value to not be sign extended and to loose that it was a negative number in the assignment. Before the patch (in my freezer), w1_slave ed fe 4b 46 7f ff 03 10 e4 : crc=e4 YES ed fe 4b 46 7f ff 03 10 e4 t=4078 With the patch, e3 fe 4b 46 7f ff 0d 10 81 : crc=81 YES e3 fe 4b 46 7f ff 0d 10 81 t=-17 Signed-off-by:
-
Bjorn Helgaas authored
The IT8705F and related parts are Super I/O controllers that contain many separate devices. Some BIOSes describe IT8705F I/O port usage under a motherboard device (PNP0C02) with overlapping regions, e.g., 0x290-0x29f and 0x290-0x294. The it87 driver supports only the Environment Controller, which requires only two ISA ports, but it used to request an eight-port range. If that range exceeds a range reported by the BIOS, as 0x290-0x297 would, the request fails, and the it87 driver cannot claim the device. This patch makes the it87 driver request only the two ports used for the Environment Controller device. Systems where this problem has been reported: Gigabyte GA-K8N Ultra 9 Gigabyte M56S-S3 Gigabyte GA-965G-DS3 Kernel bug reports: http://bugzilla.kernel.org/show_bug.cgi?id=9514 http://lkml.org/lkml/2007/12/4/466 Related change: http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=a7839e960675b549f06209d18283d5cee2ce9261 The patch above increases the number of PNP port resources we support. Prior to this patch, we ignored some port resources, which masked the it87 problem. Signed-off-by:Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by:
Mark M. Hoffman <mhoffman@lightlink.com>
-
Ingo Molnar authored
setting cpu share to 1 causes hangs, as reported in: http://bugzilla.kernel.org/show_bug.cgi?id=9779 as the default share is 1024, the values of 0 and 1 can indeed cause problems. Limit it to 2 or higher values. These values can only be set by the root user - but still it makes sense to protect against nonsensical values. Signed-off-by: -
Thomas Gleixner authored
This reverts commit d4d25dec. It tried to fix long standing bugzilla entries, but the solution was reported to break other systems. The reporter of http://bugzilla.kernel.org/show_bug.cgi?id=9791 tracked it down to this commit and confirmed that reverting the patch restores the correct behaviour. It's too late in the release cycle to find a better solution than reverting the commit to avoid regressions. Signed-off-by:
-
Linus Nilsson authored
Change two occurances of "behavour" to "behaviour". Signed-off-by:
Linus Nilsson <lajnold@acc.umu.se> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6: selinux: fix memory leak in netlabel code
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: [ICMP]: ICMP_MIB_OUTMSGS increment duplicated [IPV6]: RFC 2011 compatibility broken [IPV6]: ICMP6_MIB_OUTMSGS increment duplicated [NET]: rtnl_link: fix use-after-free [AF_KEY]: Fix skb leak on pfkey_send_migrate() error [ATM] atm/suni.c: Fix section mismatch. [ATM] atm/idt77105.c: Fix section mismatch. [IrDA]: af_irda memory leak fixes [NEIGH]: Revert 'Fix race between neigh_parms_release and neightbl_fill_parms' [NETFILTER]: bridge-netfilter: fix net_device refcnt leaks [IPV6] ROUTE: Make sending algorithm more friendly with RFC 4861. [IPV4] FIB_HASH : Avoid unecessary loop in fn_hash_dump_zone() [NET]: Fix interrupt semaphore corruption in Intel drivers. [IPV4] fib_trie: fix duplicated route issue [IPV4] fib_hash: fix duplicated route issue [IPV6]: Mischecked tw match in __inet6_check_established. rfkill: call rfkill_led_trigger_unregister() on error
-
git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds authored
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: tc35815: Use irq number for tc35815-mac platform device id [MIPS] Malta: Fix reading the PCI clock frequency on big-endian [MIPS] SMTC: Fix build error.
-
Andrew G. Morgan authored
In linux-2.6.24-rc1, security/commoncap.c:cap_inh_is_capped() was introduced. It has the exact reverse of its intended behavior. This led to an unintended privilege esculation involving a process' inheritable capability set. To be exposed to this bug, you need to have Filesystem Capabilities enabled and in use. That is: - CONFIG_SECURITY_FILE_CAPABILITIES must be defined for the buggy code to be compiled in. - You also need to have files on your system marked with fI bits raised. Signed-off-by:
Andrew G. Morgan <morgan@kernel.org> Signed-off-by:
-
Stefan Schmidt authored
Fix line length calculation. var->width is the size of the display in mm. We like to use the pixel size. Without this fix, dynamic (fbset) based resolution and depths changes with s3c2410_fb don't work at all. Spotted by john cass <johnpcass@yahoo.com> Signed-off-by:
Stefan Schmidt <stefan@openmoko.org> Signed-off-by:
Harald Welte <laforge@openmoko.org> Acked-by:
Ben Dooks <ben-linux@fluff.org> Acked-by:
Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by:
Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by:
-
Cyrill Gorcunov authored
Signed-off-by:
Cyrill Gorcunov <gorcunov@gmail.com> Acked-by:
Jesper Nilsson <jesper.nilsson@axis.com> Cc: Mikael Starvik <starvik@axis.com> Signed-off-by:
-
Randy Dunlap authored
The caller is __cpuinit. Also, this code block and its caller are inside #ifdef CONFIG_HOTPLUG_CPU blocks, so this code should reflect that config symbol's usage. WARNING: vmlinux.o(.text+0x4252f): Section mismatch: reference to .init.text: (between 'timer_cpu_notify' and 'msleep') Signed-off-by:
-
Randy Dunlap authored
Fix section mismatch in hrtimer.c: WARNING: vmlinux.o(.text+0x50c61): Section mismatch: reference to .init.text: (between 'hrtimer_cpu_notify' and 'down_read_trylock') Noticed by Johannes Berg and confirmed by Sam Ravnborg. Signed-off-by:
-
Alan Cox authored
If we get a data URB back from the hardware after we have put the tty to bed we go kaboom. Fortunately all we need to do is process the URB without trying to ram its contents down the throat of an ex-tty. Signed-off-by:
-
Atsushi Nemoto authored
The tc35815-mac platform device used a pci bus number and a devfn to identify its target device, but the pci bus number may vary if some bus-bridges are found. Use irq number which is be unique for embedded controllers. Signed-off-by:
Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by:
Ralf Baechle <ralf@linux-mips.org>
-
Dmitri Vorobiev authored
The JMPRS register on Malta boards keeps a 32-bit CPU-endian value. The readw() function assumes that the value it reads is a little-endian 16-bit number. Therefore, using readw() to obtain the value of the JMPRS register is a mistake. This error leads to incorrect reading of the PCI clock frequency on big-endian during board start-up. Change readw() to __raw_readl(). This was tested by injecting a call to printk() and verifying that the value of the jmpr variable was consistent with current setting of the JP4 "PCI CLK" jumper. Signed-off-by:
Dmitri Vorobiev <dmitri.vorobiev@gmail.com> Signed-off-by:
-
Frank Rowand authored
Fix compile warning (which becomes compile error due to -Werror). Type of argument "flags" for spin_lock_irqsave() was incorrect in some functions. Signed-off-by:
Frank Rowand <frank.rowand@am.sony.com> Signed-off-by:
-
- 21 Jan, 2008 6 commits
-
-
Paul Moore authored
Fix a memory leak in security_netlbl_sid_to_secattr() as reported here: * https://bugzilla.redhat.com/show_bug.cgi?id=352281Signed-off-by:
Paul Moore <paul.moore@hp.com> Signed-off-by:
James Morris <jmorris@namei.org>
-
Wang Chen authored
Commit "96793b48" (Add ICMPMsgStats MIB (RFC 4293)) made a mistake. In that patch, David L added a icmp_out_count() in ip_push_pending_frames(), remove icmp_out_count() from icmp_reply(). But he forgot to remove icmp_out_count() from icmp_send() too. Since icmp_send and icmp_reply will call icmp_push_reply, which will call ip_push_pending_frames, a duplicated increment happened in icmp_send. This patch remove the icmp_out_count from icmp_send too. Signed-off-by:
Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Wang Chen authored
The snmp6 entry name was changed, and it broke compatibility to RFC 2011. Signed-off-by:
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
-
Wang Chen authored
icmpv6_send() calls ip6_push_pending_frames() indirectly. Both ip6_push_pending_frames() and icmpv6_send() increment counter ICMP6_MIB_OUTMSGS. This patch remove the increment from icmpv6_send. Signed-off-by:
-
Patrick McHardy authored
When unregistering the rtnl_link_ops, all existing devices using the ops are destroyed. With nested devices this may lead to a use-after-free despite the use of for_each_netdev_safe() in case the upper device is next in the device list and is destroyed by the NETDEV_UNREGISTER notifier. The easy fix is to restart scanning the device list after removing a device. Alternatively we could add new devices to the front of the list to avoid having dependant devices follow the device they depend on. A third option would be to only restart scanning if dev->iflink of the next device matches dev->ifindex of the current one. For now this seems like the safest solution. With this patch, the veth rtnl_link_ops unregistration can use rtnl_link_unregister() directly since it now also handles destruction of multiple devices at once. Signed-off-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
-
Patrick McHardy authored
Signed-off-by:
-
