- 14 Jan, 2016 12 commits
-
-
Lee Jones authored
WARNING: Possible unnecessary 'out of memory' message + if (!aat2870) { + dev_err(&client->dev, total: 0 errors, 1 warnings, 524 lines checked Signed-off-by:Lee Jones <lee.jones@linaro.org>
-
Lee Jones authored
Checkpatch output: WARNING: Block comments use a trailing */ on a separate line + * - turn off */ WARNING: Missing a blank line after declarations + int ret; + ret = i2c_add_driver(&pm860x_driver); total: 0 errors, 2 warnings, 1283 lines checked Signed-off-by: -
Charles Keepax authored
Specify the device tree binding for the input clocks to Arizona devices. Signed-off-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Geliang Tang authored
Signed-off-by:
Geliang Tang <geliangtang@163.com> Signed-off-by:
-
Krzysztof Kozlowski authored
The mfd/s2mpa01.txt duplicates some of the information about bindings with old mfd/s2mps11.txt. Now common part exists entirely in mfd/samsung,sec-core.txt so: - add company prefix to file name (regulator/samsung,s2mpa01.txt), - remove duplicated information, - reorganize the contents to match style of regulator/samsung,s2mps11.txt. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by:
Mark Brown <broonie@kernel.org> Acked-by:
-
Krzysztof Kozlowski authored
The regulator/s5m8767-regulator.txt duplicates some of the information about bindings with old mfd/s2mps11.txt. Now common part exists entirely in mfd/samsung,sec-core.txt so: - add company prefix to file name (regulator/samsung,s5m8767.txt), - remove duplicated information, - reorganize the contents to match style of regulator/samsung,s2mps11.txt. Signed-off-by:
-
Krzysztof Kozlowski authored
Bindings for Samsung S2M and S5M family PMICs are in mess. They are spread over different files and subdirectories in a non-consistent way. The devices and respective drivers for them share a lot in common so everything could be organized in a more readable way. Reorganize the S2MPS11/13/14/15 Device Tree bindings to match the drivers for this family of devices: - move mfd/s2mps11.txt to mfd/samsung,sec-core.txt for the main MFD driver (common for entire family), - split clock block to clock/samsung,s2mps11.txt, - split regulator block to regulator/samsung,s2mps11.txt. Signed-off-by:
Michael Turquette <mturquette@baylibre.com> Acked-by:
-
Linus Walleij authored
As we want gpio_chip .get() calls to be able to return negative error codes and propagate to drivers, we need to go over all drivers and make sure their return values are clamped to [0,1]. We do this by using the ret = !!(val) design pattern. Cc: Paul Parsons <lost.distance@yahoo.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
As we want gpio_chip .get() calls to be able to return negative error codes and propagate to drivers, we need to go over all drivers and make sure their return values are clamped to [0,1]. We do this by using the ret = !!(val) design pattern. Signed-off-by:
-
Linus Walleij authored
As we want gpio_chip .get() calls to be able to return negative error codes and propagate to drivers, we need to go over all drivers and make sure their return values are clamped to [0,1]. We do this by using the ret = !!(val) design pattern. Cc: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by:
-
Linus Walleij authored
As we want gpio_chip .get() calls to be able to return negative error codes and propagate to drivers, we need to go over all drivers and make sure their return values are clamped to [0,1]. We do this by using the ret = !!(val) design pattern. Cc: Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by:
-
Linus Walleij authored
As we want gpio_chip .get() calls to be able to return negative error codes and propagate to drivers, we need to go over all drivers and make sure their return values are clamped to [0,1]. We do this by using the ret = !!(val) design pattern. This also start to propagate the negative error code from the smbus call if there is one, as the last commit of this series will make the gpiolib core deal with that properly. Signed-off-by:
-
- 11 Jan, 2016 13 commits
-
-
Linus Walleij authored
As we want gpio_chip .get() calls to be able to return negative error codes and propagate to drivers, we need to go over all drivers and make sure their return values are clamped to [0,1]. We do this by using the ret = !!(val) design pattern. Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Charles Keepax authored
Update the device tree binding documentation to include the wlf,out-mono property that is used to specify whether each output is a mono or stereo output. Signed-off-by:
-
Charles Keepax authored
Add device tree bindings to support specifying outputs from the chip as mono outputs. Whilst we are doing it change the out_mono pdata from a bool to an int, because Sparse gets upset about using ARRAY_SIZE on bools. Signed-off-by:
-
Geert Uytterhoeven authored
Allow support for the DA9063 PMIC to be modular, cfr. DA9062, which allows to decrease size of multi-platform kernels (e.g. multi_v7_defconfig). Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by:
-
Charles Keepax authored
Currently the driver requests the boot done and control interface IRQs before it has requested its own IRQ line. This can cause problems on edge triggered IRQ systems as if an edge occurs before the parent IRQ is enabled it will be missed. Whilst we are changing the error handling remove an unused label as well. Signed-off-by:
-
Richard Fitzgerald authored
The CS47L24 and WM1831 codecs only have two GPIO lines, but are otherwise similar to the WM8280. Signed-off-by:
Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Acked-by:
-
Arnd Bergmann authored
The newly introduced as3722_i2c_suspend/resume functions are built unconditionally, but only used when power management is enabled, so we get a warning otherwise: drivers/mfd/as3722.c:427:12: warning: 'as3722_i2c_suspend' defined but not used [-Wunused-function] drivers/mfd/as3722.c:438:12: warning: 'as3722_i2c_resume' defined but not used [-Wunused-function] This marks them both as __maybe_unused, which avoids an ugly #ifdef and gives us best compile-time coverage. When they are unused, the compiler will silently drop the functions from its output. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: 35deff7e ("mfd: as3722: Handle interrupts on suspend") Signed-off-by:
-
Thierry Reding authored
These new helpers simplify implementing multi-driver modules and properly handle failure to register one driver by unregistering all previously registered drivers. Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Ivan T. Ivanov authored
Revision ID registers are available only on devices with Slave IDs that are even, so don't make access to unavailable registers. Signed-off-by:
Ivan T. Ivanov <ivan.ivanov@linaro.org> [sboyd@codeaurora.org: Consider all slave ids that are even] Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Rasmus Villemoes authored
wm831x_unique_id_show currently displays an interesting pattern of '0' and '3' characters which isn't very useful (figuring out why is left as an exercise for the reader). Presumably "buf[i]" should have been "id[i] & 0xff". But while there, it is much simpler to simply use %phN and do all the formatting at once. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by:
-
Damien Riegel authored
Currently syscon has a fixed configuration of 32 bits for register and values widths. In some cases, it would be desirable to be able to customize the value width. For example, certain boards (like the ones manufactured by Technologic Systems) have a FPGA that is memory-mapped, but its registers are only 16-bit wide. This patch adds an optional "reg-io-width" DT binding for syscon that allows to change the width for the data bus (i.e. val_bits). If this property is provided, it will also set the register stride to reg-io-width's value. If not provided, the default configuration is used. Signed-off-by:
Damien Riegel <damien.riegel@savoirfairelinux.com> Acked-by:
-
Charles Keepax authored
Signed-off-by:
-
Nicolas Boichat authored
cros_ec_cmd_xfer_spi and cros_ec_pkt_xfer_spi generally work like this: - Pull CS down (active), wait a bit, then send a command - Wait for response (multiple requests) - Wait a while, pull CS up (inactive) These operations, individually, lock the SPI bus, but there is nothing preventing the SPI framework from interleaving messages intended for other devices as the bus is unlocked in between. This is a problem as the EC expects CS to be held low for the whole duration. Solution: Lock the SPI bus during the whole transaction, to make sure that no other messages can be interleaved. Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Reviewed-by:
Gwendal Grignou <gwendal@chromium.org> Signed-off-by:
-
- 04 Dec, 2015 8 commits
-
-
Richard Fitzgerald authored
The CS47L24 source is part of the ex-Wolfson "Arizona" group of drivers. Not all cs47lxx devices are part of the Arizona driver group so the cs47l24 is explicitly listed by its full part number. Signed-off-by:
-
Richard Fitzgerald authored
This patch adds the regmap configuration tables and core MFD handling for the CS47L24 and WM1831 codecs. Note that compared to the other Arizona codecs, these devices do not have an LDO1 or micsupp regulators, extcon driver, or the DCVDD isolation control. Signed-off-by:
-
Richard Fitzgerald authored
This updates the Arizona MFD device tree bindings to add the Cirrus Logic CS47L24 and WM1831 codecs. Note that unlike all the other codecs the DCVDD-supply and MICVDD-supply are mandatory. Signed-off-by:
-
LABBE Corentin authored
of_match_device could return NULL, and so cause a NULL pointer dereference later. Signed-off-by:
LABBE Corentin <clabbe.montjoie@gmail.com> Signed-off-by:
-
Linus Walleij authored
The platforms that use the AB8500 define all IRQ resources in the device tree and they are automatically populated by matching the .of_compatible string. These static resources are just surplus baggage these days. Signed-off-by:
-
Julia Lawall authored
The da903x_chip_ops structure is never modified, so declare it as const. Done with the help of Coccinelle. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Saurabh Sengar authored
For checking if a property is present or not, use of_property_read_bool instead of of_get_property() Signed-off-by:
Saurabh Sengar <saurabh.truth@gmail.com> Signed-off-by:
-
Jon Hunter authored
The as3722 device is registered as an irqchip and the as3722-rtc interrupt is one of it's interrupt sources. When using the as3722-rtc as a wake-up device from suspend, the following is seen: PM: Syncing filesystems ... done. Freezing user space processes ... (elapsed 0.001 seconds) done. Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. Suspending console(s) (use no_console_suspend to debug) PM: suspend of devices complete after 161.119 msecs PM: late suspend of devices complete after 1.048 msecs PM: noirq suspend of devices complete after 0.756 msecs Disabling non-boot CPUs ... CPU1: shutdown CPU2: shutdown CPU3: shutdown Entering suspend state LP1 Enabling non-boot CPUs ... CPU1 is up CPU2 is up CPU3 is up PM: noirq resume of devices complete after 0.487 msecs as3722 4-0040: Failed to read IRQ status: -16 as3722 4-0040: Failed to read IRQ status: -16 as3722 4-0040: Failed to read IRQ status: -16 as3722 4-0040: Failed to read IRQ status: -16 ... The reason why the as3722 interrupt status cannot be read is because the as3722 interrupt is not masked during suspend and when the as3722-rtc interrupt occurs, to wake-up the device, the interrupt is seen before the i2c controller has been resumed in order to read the as3722 interrupt status. The as3722-rtc driver sets it's interrupt as a wake-up source during suspend, which gets propagated to the parent as3722 interrupt. However, the as3722-rtc driver cannot disable it's interrupt during suspend otherwise we would never be woken up and so the as3722 must disable it's interrupt instead. Fix this by disabling the as3722 interrupt during suspend. To ensure that a wake-up event from the as3722 is not missing, enable the as3722 interrupt as a wake-up source before disabling the interrupt on entering suspend. Signed-off-by:
Jon Hunter <jonathanh@nvidia.com> Signed-off-by:
-
- 24 Nov, 2015 4 commits
-
-
Charles Keepax authored
The MFD part of wm8994 consists of three files wm8994-core.c, wm8994-irq.c and wm8994-regmap.c only wm8994-core.c has a MODULE_DESCRIPTION / LICENSE. These were clearly intended to be built as a single module, but currently are not. This will lead to a tainted kernel when loading modules for wm8894-irq.c and wm8994-regmap.c because are missing a license. This patch fixes this issue by grouping the three files together into a single module. Reported-by:
Peter Robinson <pbrobinson@gmail.com> Signed-off-by:
-
Andrew F. Davis authored
Fix the incorrect interrupt documentation file path in binding docs. Signed-off-by:
Andrew F. Davis <afd@ti.com> Signed-off-by:
-
Alim Akhtar authored
Currently S2MPSXX multifunction device is named as *-pmic, and these MFDs also supports regulator as a one of its MFD cell which has the same name, because current name is confusing and we want to sort it out. We did discussed different approaches about how the MFD and it cells need to be named here [1]. Based in the discussion this patch rename MFD regulator name as *-regulator instead of current *-pmic. This patch also changes the corresponding entries in the regulator driver to keep git-bisect happy. [1]-> https://lkml.org/lkml/2015/10/28/417Suggested-by:
Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by:
-
Alexandra Yates authored
Adding Intel codename Lewisburg platform device IDs for PCH. Signed-off-by:
Alexandra Yates <alexandra.yates@linux.intel.com> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
-
- 23 Nov, 2015 3 commits
-
-
Alim Akhtar authored
RTC found in s2mps15 is almost same as one found on s2mps13 with few differences in RTC_UPDATE register fields, like: 1> Bit[4] and Bit[1] are reversed - On s2mps13 WUDR -> bit[4], AUDR -> bit[1] - On s2mps15 WUDR -> bit[1], AUDR -> bit[4] 2> In case of s2mps13, for alarm register, need to set both WDUR and ADUR high, whereas for s2mps15 only set AUDR to high. 3> On s2mps15, WUDR, RUDR and AUDR functions should never be used at the same time. This patch add required changes to enable s2mps15 rtc timer. Signed-off-by:Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
-
Thomas Abraham authored
The S2MPS15 PMIC is similar in functionality to S2MPS11/14 PMIC. It contains 27 LDO and 10 Buck regulators and allows programming these regulators via a I2C interface. This patch adds initial support for LDO/Buck regulators of S2MPS15 PMIC. Signed-off-by:
Thomas Abraham <thomas.ab@samsung.com> Signed-off-by:
-
Thomas Abraham authored
Add support for S2MPS15 PMIC which is similar to S2MPS11 PMIC. The S2MPS15 PMIC supports 27 LDO regulators, 10 buck regulators, RTC, three 32.768KHz clock outputs and battery charger. This patch adds initial support for LDO and buck regulators of S2MPS15 device. Signed-off-by:
-
