Recent versions of checkpatch have a new warning based on a documented
preference of Linus to not use bool in structures due to wasted space and
the size of bool is implementation dependent.  For more information, see
the email thread at https://lkml.org/lkml/2017/11/21/384.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In ice_vsi_setup_[tx|rx]_rings, err is uninitialized which can result in
a garbage value return to the caller. Fix that.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1) When ice_ena_msix_range() fails to reserve vectors, a devm_kfree()
   warning was seen in the error flow path. So check pf->irq_tracker
   before use in ice_clear_interrupt_scheme().

2) In ice_vsi_cfg(), check vsi->netdev before use.

3) In ice_get_link_status, check link_up before use.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the following interrupt causes that are not applicable or not
handled:
- PFINT_OICR_HLP_RDY_M
- PFINT_OICR_CPM_RDY_M
- PFINT_OICR_GPIO_M
- PFINT_OICR_STORM_DETECT_M

Add the following interrupt cause that's actually handled in ice_misc_intr:
- PFINT_OICR_PE_CRITERR_M
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the struct ice_aqc_vsi_props the field port_vlan_flags is an
overloaded term because it is used for both port VLANs (PVLANs) and
regular VLANs. This is an issue and is very confusing especially when
dealing with VFs because normal VLANs and port VLANs are not the same.
To fix this the field was renamed to vlan_flags and all of the #define's
labeled *_PVLAN_* were renamed to *_VLAN_* if they are not specific to
port VLANs.

Also in ice_vsi_manage_vlan_stripping, set the ICE_AQ_VSI_VLAN_MODE_ALL
bit to allow the driver to add a VLAN tag to all packets it sends.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, we use a combination of ilog2 and is_power_of_2() to
calculate the next power of 2 for the qcount. This appears to be causing
a warning on some combinations of GCC and the Linux kernel:

MODPOST 1 modules
WARNING: "____ilog2_NaN" [ice.ko] undefined!

This appears to because because GCC realizes that qcount could be zero
in some circumstances and thus attempts to link against the
intentionally undefined ___ilog2_NaN function.

The order_base_2 function is intentionally defined to return 0 when
passed 0 as an argument, and thus will be safe to use here.

This not only fixes the warning but makes the resulting code slightly
cleaner, and is really what we should have used originally.

Also update the comment to make it more clear that we are rounding up,
not just incrementing the ilog2 of qcount unconditionally.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a consolidation of multiple bug fixes for control queue
processing.

1)  In ice_clean_adminq_subtask() remove unnecessary reads/writes to
    registers. The bits PFINT_FW_CTL, PFINT_MBX_CTL and PFINT_SB_CTL
    are not set when an interrupt arrives, which means that clearing them
    again can be omitted.

2)  Get an accurate value in "pending" by re-reading the control queue
    head register from the hardware.

3)  Fix a corner case involving lost control queue messages by checking
    for new control messages (using ice_ctrlq_pending) before exiting the
    cleanup routine.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean control queues only when they are initialized. One of the ways to
validate if the basic initialization is done is by checking value of
cq->sq.head and cq->rq.head variables that specify the register address.
This patch adds a check to avoid NULL pointer dereference crash when tried
to shutdown uninitialized control queue.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It is not safe to have the string table for statistics change order or
size over the lifetime of a given netdevice. This is because of the
nature of the 3-step process for obtaining stats. First, user space
performs a request for the size of the strings table. Second it performs
a separate request for the strings themselves, after allocating space
for the table. Third, it requests the stats themselves, also allocating
space for the table.

If the size decreased, there is potential to see garbage data or stats
values. In the worst case, we could potentially see stats values become
mis-aligned with their strings, so that it looks like a statistic is
being reported differently than it actually is.

Even worse, if the size increased, there is potential that the strings
table or stats table was not allocated large enough and the stats code
could access and write to memory it should not, potentially resulting in
undefined behavior and system crashes.

It isn't even safe if the size always changes under the RTNL lock. This
is because the calls take place over multiple user space commands, so it
is not possible to hold the RTNL lock for the entire duration of
obtaining strings and stats. Further, not all consumers of the ethtool
API are the user space ethtool program, and it is possible that one
assumes the strings will not change (valid under the current contract),
and thus only requests the stats values when requesting stats in a loop.

Finally, it's not possible in the general case to detect when the size
changes, because it is quite possible that one value which could impact
the stat size increased, while another decreased. This would result in
the same total number of stats, but reordering them so that stats no
longer line up with the strings they belong to. Since only size changes
aren't enough, we would need some sort of hash or token to determine
when the strings no longer match. This would require extending the
ethtool stats commands, but there is no more space in the relevant
structures.

The real solution to resolve this would be to add a completely new API
for stats, probably over netlink.

In the ice driver, the only thing impacting the stats that is not
constant is the number of queues. Instead of reporting stats for each
used queue, report stats for each allocated queue. We do not change the
number of queues allocated for a given netdevice, as we pass this into
the alloc_etherdev_mq() function to set the num_tx_queues and
num_rx_queues.

This resolves the potential bugs at the slight cost of displaying many
queue statistics which will not be activated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use define for the unit size shift of the Rx LAN context descriptor base
address instead of the magic number 7.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There is already a check for owner == ICE_SCHED_NODE_OWNER_LAN at the
beginning of ice_sched_update_vsi_child_nodes. Remove the additional
check to address the static analysis tool smatch issue "warn: we tested
'owner' before and it was 'false'".
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the following smatch errors:

1) Fix "odd binop '0x0 & 0xc'" when performing the bitwise-and with a
   constant value of zero (ICE_AQC_GSET_RSS_LUT_TABLE_SIZE_128_FLAG).
   Remove a similar bitwise-and with 0 in ice_add_marker_act() and use the
   right mask ICE_LG_ACT_GENERIC_OFFSET_M in the expression.

2) Fix a similar issue "odd binop '0x0 & 0x1800' in ice_req_irq_msix_misc.

3) Fix "odd binop '0x380000 & 0x7fff8'" in ice_add_marker_act(). Also, use
   a new define ICE_LG_ACT_GENERIC_OFF_RX_DESC_PROF_IDX instead of magic
   number '7'.

4) Fix warn: odd binop '0x0 & 0x18' in ice_set_dflt_vsi_ctx() by removing
   unnecessary logic to explicitly unset bits 3 and 4 in port_vlan_bits.
   These bits are unset already by the memset on ctxt->info.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Johan Hedberg says:

====================
pull request: bluetooth 2018-08-23

Here are two important Bluetooth fixes for the MediaTek and RealTek HCI
drivers.

Please let me know if there are any issues pulling, thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: bug fix & optimization for HNS3 driver

This patchset presents a bug fix found out when CONFIG_ARM64_64K_PAGES
enable and an optimization for HNS3 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

'truesize' is supposed to be u32, not int, so fix it.
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When enable the config item "CONFIG_ARM64_64K_PAGES", the size of
PAGE_SIZE is 65536(64K). But the type of page_offset is u16, it will
overflow. So change it to u32, when "CONFIG_ARM64_64K_PAGES" enabled.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 6edb3c96 ("net/ipv6: Defer initialization of dst to data path")
forgot to handle anycast route and init anycast rt->dst.input to ip6_forward.
Fix it by setting anycast rt->dst.input back to ip6_input.

Fixes: 6edb3c96 ("net/ipv6: Defer initialization of dst to data path")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns: bug fixes & optimization for HNS driver

This patchset presents some bug fixes found out when CONFIG_ARM64_64K_PAGES
enable and an optimization for HNS driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update hns to drop the hns_nic_get_headlen function in favour of
eth_get_headlen, and hence also removes now redundant hns_nic_get_headlen.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->truesize is not meant to be tracking amount of used bytes in a skb,
but amount of reserved/consumed bytes in memory.

For instance, if we use a single byte in last page fragment, we have to
account the full size of the fragment.

So skb_add_rx_frag needs to calculate the length of the entire buffer into
turesize.

Fixes: 9cbe9fd5 ("net: hns: optimize XGE capability by reducing cpu usage")
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'truesize' is supposed to be u32, not int, so fix it.
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When enable the config item "CONFIG_ARM64_64K_PAGES", the size of PAGE_SIZE
is 65536(64K). But the  type of length and page_offset are u16, they will
overflow. So change them to u32.

Fixes: 6fe6611f ("net: add Hisilicon Network Subsystem hnae framework support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kevin Yang says:

====================
tcp_bbr: PROBE_RTT minor bug fixes

This series includes two minor bug fixes for the TCP BBR PROBE_RTT
mechanism, and one preparatory patch:

(1) A preparatory patch to reorganize the PROBE_RTT logic by refactoring
    (into its own function) the code to exit PROBE_RTT, since the next
    patch will be using that code in a new context.

(2) Fix: When BBR restarts from idle and if BBR is in PROBE_RTT mode,
    BBR should check if it's time to exit PROBE_RTT. If yes, then BBR
    should exit PROBE_RTT mode and restore the cwnd to its full value.

(3) Fix: Apply the PROBE_RTT cwnd cap even if the count of fully-ACKed
    packets is 0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit fixes a corner case where TCP BBR would enter PROBE_RTT
mode but not reduce its cwnd. If a TCP receiver ACKed less than one
full segment, the number of delivered/acked packets was 0, so that
bbr_set_cwnd() would short-circuit and exit early, without cutting
cwnd to the value we want for PROBE_RTT.

The fix is to instead make sure that even when 0 full packets are
ACKed, we do apply all the appropriate caps, including the cap that
applies in PROBE_RTT mode.

Fixes: 0f8782ea ("tcp_bbr: add BBR congestion control")
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix the case where BBR does not exit PROBE_RTT mode when
it restarts from idle. When BBR restarts from idle and if BBR is in
PROBE_RTT mode, BBR should check if it's time to exit PROBE_RTT. If
yes, then BBR should exit PROBE_RTT mode and restore the cwnd to its
full value.

Fixes: 0f8782ea ("tcp_bbr: add BBR congestion control")
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add a helper function bbr_check_probe_rtt_done() to
  1. check the condition to see if bbr should exit probe_rtt mode;
  2. process the logic of exiting probe_rtt mode.

Fixes: 0f8782ea ("tcp_bbr: add BBR congestion control")
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp uses per-cpu (and per namespace) sockets (net->ipv4.tcp_sk) internally
to send some control packets.

1) RST packets, through tcp_v4_send_reset()
2) ACK packets in SYN-RECV and TIME-WAIT state, through tcp_v4_send_ack()

These packets assert IP_DF, and also use the hashed IP ident generator
to provide an IPv4 ID number.

Geoff Alexander reported this could be used to build off-path attacks.

These packets should not be fragmented, since their size is smaller than
IPV4_MIN_MTU. Only some tunneled paths could eventually have to fragment,
regardless of inner IPID.

We really can use zero IPID, to address the flaw, and as a bonus,
avoid a couple of atomic operations in ip_idents_reserve()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Geoff Alexander <alexandg@cs.unm.edu>
Tested-by: Geoff Alexander <alexandg@cs.unm.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

All the 3 callers of addrconf_add_mroute() assert RTNL
lock, they don't take any additional lock either, so
it is safe to convert it to GFP_KERNEL.

Same for sit_add_v4_addrs().

Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new tcf_exts_for_each_action() macro doesn't reference its
arguments when CONFIG_NET_CLS_ACT is disabled, which leads to
a harmless warning in at least one driver:

drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c: In function 'tc_fill_actions':
drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c:64:6: error: unused variable 'i' [-Werror=unused-variable]

Adding a cast to void lets us avoid this kind of warning.
To be on the safe side, do it for all three arguments, not
just the one that caused the warning.

Fixes: 244cd96a ("net_sched: remove list_head from tc_action")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TC filter flow mapping override completely skipped the call to
cake_hash(); however that meant that the internal state was not being
updated, which ultimately leads to deadlocks in some configurations. Fix
that by passing the overridden flow ID into cake_hash() instead so it can
react appropriately.

In addition, the major number of the class ID can now be set to override
the host mapping in host isolation mode. If both host and flow are
overridden (or if the respective modes are disabled), flow dissection and
hashing will be skipped entirely; otherwise, the hashing will be kept for
the portions that are not set by the filter.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ncsi_pkg_info_all_nl() .dumpit handler is missing the NLM_F_MULTI
flag, causing additional package information after the first to be lost.
Also fixup a sanity check in ncsi_write_package_info() to reject out of
range package IDs.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cong Wang says:

====================
net_sched: pending clean up and bug fixes

This patchset aims to clean up and fixes some bugs in current
merge window, this is why it is targeting -net.

Patch 1-5 are clean up Vlad's patches merged in current merge
window, patch 6 is just a trivial cleanup.

Patch 7 reverts a lockdep warning fix and patch 8 provides a better
fix for it.

Patch 9 fixes a potential deadlock found by me during code review.

Please see each patch for details.
====================
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>

use_all_metadata() acquires read_lock(&ife_mod_lock), then calls
add_metainfo() which calls find_ife_oplist() which acquires the same
lock again. Deadlock!

Introduce __add_metainfo() which accepts struct tcf_meta_ops *ops
as an additional parameter and let its callers to decide how
to find it. For use_all_metadata(), it already has ops, no
need to find it again, just call __add_metainfo() directly.

And, as ife_mod_lock is only needed for find_ife_oplist(),
this means we can make non-atomic allocation for populate_metalist()
now.

Fixes: 817e9f2c ("act_ife: acquire ife_mod_lock before reading ifeoplist")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only time we need to take tcfa_lock is when adding
a new metainfo to an existing ife->metalist. We don't need
to take tcfa_lock so early and so broadly in tcf_ife_init().

This means we can always take ife_mod_lock first, avoid the
reverse locking ordering warning as reported by Vlad.
Reported-by: Vlad Buslov <vladbu@mellanox.com>
Tested-by: Vlad Buslov <vladbu@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 42c625a4 ("net: sched: act_ife: disable bh
when taking ife_mod_lock"), because what ife_mod_lock protects
is absolutely not touched in rate est timer BH context, they have
no race.

A better fix is following up.

Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 90b73b77, list_head is no longer needed.
Now we just need to convert the list iteration to array
iteration for drivers.

Fixes: 90b73b77 ("net: sched: change action API to use array of pointers to actions")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcf_idr_check() is replaced by tcf_idr_check_alloc(),
and __tcf_idr_check() now can be folded into tcf_idr_search().

Fixes: 0190c1d4 ("net: sched: atomically check-allocate action")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 16af6067 ("net: sched: implement reference counted action release")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>