This change fixes several issues found in ntuple filtering while I was
doing the ATR refactor.

Specifically I updated the masks to work correctly with the latest version
of ethtool, I cleaned up the exception handling and added detailed error
output when a filter is rejected, and corrected several bits that were set
incorrectly in ixgbe_type.h.

The previous version of this patch included a printk that was left over from
me fixing the filter setup.  This patch does not include that printk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change adds a compressed input type for atr signature hash
computation.  It also drops the use of the set functions when setting up
the ATR input since we can then directly setup the hash input as two dwords
that can be stored and passed as registers.

With these changes the cost of computing the has is low enough that we can
perform a hash computation on each TCP SYN flagged packet allowing us to
drop the number of flow director misses considerably in tests such as
netperf TCP_CRR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change cleans up the layout of the flow director data, and the
algorithm used to calculate the hash resulting in a 35x / 3500% performance
increase versus the old flow director hash computation.  The overall effect
is only a 1% increase in transactions per second though due to the fact
that only 1 packet in 20 are actually hashed upon.

TCP_RR before:
Socket Size   Request  Resp.   Elapsed  Trans.
Send   Recv   Size     Size    Time     Rate
bytes  Bytes  bytes    bytes   secs.    per sec

16384  87380  1        1       60.00    23059.27
16384  87380

TCP_RR after:
Socket Size   Request  Resp.   Elapsed  Trans.
Send   Recv   Size     Size    Time     Rate
bytes  Bytes  bytes    bytes   secs.    per sec

16384  87380  1        1       60.00    23239.98
16384  87380
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When disable the Rx logic globally, we would also want to disable the per Rx
queue receive logic by per queue Rx control register RXDCTL so no more DMA is
happening from the packet buffer to the receive buffer associated with the Rx
ring, before we start unmapping Rx ring receive buffer. The hardware may take
max of 100us before the corresponding Rx queue is really disabled. Added
ixgbe_disable_rx_queue() for this purpose.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the gigabit phys present on the CE4100 reference
platforms.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

82574 needs to configure Low Power Link Up (or LPLU) differently than
the other parts in the 8257x family supported by the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Phys supported by the driver do not remain powered off across a reset
of the device when the interface is down, e.g. on 82571, but not on 82574.
This patch powers down (only when WoL is disabled) the PHY after a reset if
the interface is down and the ethtool diagnostics are not currently running.

The ethtool diagnostic function required a minor re-factor as a result, and
the e1000_[get|put]_hw_control() functions are renamed since they are no
longer static to netdev.c as they are needed by the ethtool diagnostics.
A couple minor whitespace issues were cleaned up, too.
Reported-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For the 82579 jumbo frame workaround, there is no need to re-write the CRC
calculation functionality already found in the kernel's ether_crc_le().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use string functions with bounds checking rather than their non-bounds
checking counterparts, and do not hard code these boundaries.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleans up the code a bit by using the driver-specific e1e_rphy and
e1e_wphy macros instead of the full function pointer variants.  Fix
a couple whitespace issue with two already existing calls to e1e_wphy.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ICR register is clear on read and we don't care what the returned value
is when resetting the hardware so the icr variable(s) can be removed.  We
should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and
from e1000_get_phy_id_82571() (dump a debug message when it fails and when
an unknown Phy id is returned).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to compute the features for other offloads (primarily
scatter/gather), we need to first check the ability of the NIC to
offload the checksum for the packet.  Since we have already computed
this, we can directly use the result instead of figuring it out
again.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This switches skb_need_linearize() to use the features that have
been centrally computed.  In doing so, this fixes a problem where
scatter/gather should not be used because the card does not support
checksum offloading on that type of packet.  On device registration
we only check that some form of checksum offloading is available if
scatter/gatther is enabled but we must also check at transmission
time.  Examples of this include IPv6 or vlan packets on a NIC that
only supports IPv4 offloading.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This switches dev_gso_segment() to use the device features computed
by the centralized routine.  In doing so, it fixes a problem where
it would always use dev->features, instead of those appropriate
to the number of vlan tags if any are present.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that there is a single function that can compute the device
features relevant to a packet, we don't want to run it for each
offload.  This converts netif_needs_gso() to take the features
of the device, rather than computing them itself.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netif_get_vlan_features() is currently only used by netif_needs_gso(),
so it only concerns itself with GSO features.  However, several other
places also should take into account the contents of the packet when
deciding whether to offload to hardware.  This generalizes the function
to return features about all of the various forms of offloading.  Since
offloads tend to be linked together, this avoids duplicating the logic
in each location (i.e. the scatter/gather code also needs the checksum
logic).
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently only have software fallback for one type of checksum: the
TCP/UDP one's complement.  This means that a protocol that uses hardware
offloading for a different type of checksum (FCoE, SCTP) must directly
check the device's features and do the right thing ahead of time.  By
the time we get to dev_can_checksum(), we're only deciding whether to
apply the one algorithm in software or hardware.  NETIF_F_HW_CSUM has the
same capabilities as the software version, so we should always use it if
present.  The primary advantage of this is multiply tagged vlans can use
hardware checksumming.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It workarounds the 60s firmware load failure timeout for the
non-modular case.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix new kernel-doc notation warning in net/core/filter.c:

Warning(net/core/filter.c:172): No description found for parameter 'fentry'
Warning(net/core/filter.c:172): Excess function parameter 'filter' description in 'sk_run_filter'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix new kernel-doc notation warning in sock.h by annotating skc_dontcopy_*
as private fields.

Warning(include/net/sock.h:163): No description found for parameter 'skc_dontcopy_end[0]'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to NLM_F_DUMP is composed of two bits, NLM_F_ROOT | NLM_F_MATCH,
when doing "if (x & NLM_F_DUMP)", it tests for _either_ of the bits
being set. Because NLM_F_MATCH's value overlaps with NLM_F_EXCL,
non-dump requests with NLM_F_EXCL set are mistaken as dump requests.

Substitute the condition to test for _all_ bits being set.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The forcedeth driver uses the legacy PCI power management, so it has
to do PCI-specific things in its ->suspend() and ->resume() callbacks
and some of them are not done correctly.

Convert forcedeth to the new PCI power management framework and make
it let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.

Tested with nVidia Corporation MCP55 Ethernet (rev a2).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

This converts sky2 to new VLAN offload flags control via ethtool.
It also allows for transmit offload of vlan tagged frames which
was not possible before.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sky2 driver would always try all possible supported speeds even
if the user only asked for a limited set of speed/duplex combinations.
Reported-by: Mohsen Hariri <m.hariri@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the race on bp->stats_pending between the timer and a LINK_UP event
handler.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move to D0 before clearing MSI/MSI-X configuration. Otherwise MSI/MSI-X
won't be cleared.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes in registers dump:
        - Properly calculate dump length for 57712.
        - Prevent HW blocks parity attentions when dumping registers in order to
prevent false parity errors handling.
        - Update the bnx2x_dump.h file: old one had a few bugs that could cause
fatal HW error as a result of a registers dump.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't prevent RSS configuration in INT#x and MSI interrupt modes. Otherwise
Rx hash key won't be available.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Madge Ambassador ATM Adapter driver: Always release_firmware() in ucode_init() and don't leak memory.

Failure to call release_firmware() will result in memory leak in
drivers/atm/ambassador.c::ucode_init().
This patch makes sure we always call release_firmware() when needed,
thus removing the leak(s).

Yes, I know checkpatch complains about this patch, but it was either that
or completely mess up the existing style, so I opted to use the existing
style and live with the checkpatch related flak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Failure to release_firmware() in drivers/net/hamradio/yam.c::add_mcs()
causes memory leak.
This patch should fix it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add mx28 dual fec support. Here are some key notes
for mx28 fec controller.

 - The mx28 fec controller naming ENET-MAC is a different IP from FEC
   used on other i.mx variants.  But they are basically compatible
   on software interface, so it's possible to share the same driver.
 - ENET-MAC design on mx28 made an improper assumption that it runs
   on a big-endian system. As the result, driver has to swap every
   frame going to and coming from the controller.
 - The external phys can only be configured by fec0, which means fec1
   can not work independently and both phys need to be configured by
   mii_bus attached on fec0.
 - ENET-MAC reset will get mac address registers reset too.
 - ENET-MAC MII/RMII mode and 10M/100M speed are configured
   differently FEC.
 - ETHER_EN bit must be set to get ENET-MAC interrupt work.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following commit made a fix to use fec_enet_open/fec_enet_close
over fec_enet_init/fec_stop for suspend/resume, because fec_enet_init
does not allow to have a working network interface at resume.

  e3fe8558
  net/fec: fix pm to survive to suspend/resume

This fix works for i.mx/mxc fec controller, but fails on mx28 fec
which gets a different interrupt logic design. On i.mx fec, interrupt
can be triggered even bit ETHER_EN of ECR register is not set. But
on mx28 fec, ETHER_EN must be set to get interrupt work. Meanwhile,
MII interrupt is mandatory to resume the driver, because MDIO
read/write changed to interrupt mode by commit below.

  97b72e43
  fec: use interrupt for MDIO completion indication

fec_restart/fec_stop comes out as the solution working for both
cases.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add mac field into fec_platform_data and consolidate function
fec_get_mac to get mac address in following order.

 1) module parameter via kernel command line fec.macaddr=0x00,0x04,...
 2) from flash in case of CONFIG_M5272 or fec_platform_data mac
    field for others, which typically have mac stored in fuse
 3) fec mac address registers set by bootloader
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "index" becomes legacy since fep->pdev->id starts working
to identify the instance.

Moreover, the call of fec_enet_init(ndev, 0) always passes 0
to fep->index. This makes the following code in fec_get_mac buggy.

	/* Adjust MAC if using default MAC address */
	if (iap == fec_mac_default)
		dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;

It may be the time to remove "index" and use fep->pdev->id instead.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FEC_MMFR_OP_WRITE should be used than FEC_MMFR_OP_READ in
a mdio write operation.

It's probably a typo introduced by commit:

e6b043d5
netdev/fec.c: add phylib supporting to enable carrier detection (v2)
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/hfsplus:
  hfsplus: %L-to-%ll, macro correction, and remove unneeded braces
  hfsplus: spaces/indentation clean-up
  hfsplus: C99 comments clean-up
  hfsplus: over 80 character lines clean-up
  hfsplus: fix an artifact in ioctl flag checking
  hfsplus: flush disk caches in sync and fsync
  hfsplus: optimize fsync
  hfsplus: split up inode flags
  hfsplus: write up fsync for directories
  hfsplus: simplify fsync
  hfsplus: avoid useless work in hfsplus_sync_fs
  hfsplus: make sure sync writes out all metadata
  hfsplus: use raw bio access for partition tables
  hfsplus: use raw bio access for the volume headers
  hfsplus: always use hfsplus_sync_fs to write the volume header
  hfsplus: silence a few debug printks
  hfsplus: fix option parsing during remount

Fix up conflicts due to VFS changes in fs/hfsplus/{hfsplus_fs.h,unicode.c}

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
  spi/omap: Fix DMA API usage in OMAP MCSPI driver
  spi/imx: correct the test on platform_get_irq() return value
  spi/topcliff: Typo fix threhold to threshold
  spi/dw_spi Typo change diable to disable.
  spi/fsl_espi: change the read behaviour of the SPIRF
  spi/mpc52xx-psc-spi: move probe/remove to proper sections
  spi/dw_spi: add DMA support
  spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
  spi/dw_spi: Fix too short timeout in spi polling loop
  spi/pl022: convert running variable
  spi/pl022: convert busy flag to a bool
  spi/pl022: pass the returned sglen to the DMA engine
  spi/pl022: map the buffers on the DMA engine
  spi/topcliff_pch: Fix data transfer issue
  spi/imx: remove autodetection
  spi/pxa2xx: pass of_node to spi device and set a parent device
  spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
  spi/pxa2xx: Add chipselect support for Sodaville
  spi/pxa2xx: Consider CE4100's FIFO depth
  spi/pxa2xx: Add CE4100 support
  ...

* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (30 commits)
  gameport: use this_cpu_read instead of lookup
  x86: udelay: Use this_cpu_read to avoid address calculation
  x86: Use this_cpu_inc_return for nmi counter
  x86: Replace uses of current_cpu_data with this_cpu ops
  x86: Use this_cpu_ops to optimize code
  vmstat: User per cpu atomics to avoid interrupt disable / enable
  irq_work: Use per cpu atomics instead of regular atomics
  cpuops: Use cmpxchg for xchg to avoid lock semantics
  x86: this_cpu_cmpxchg and this_cpu_xchg operations
  percpu: Generic this_cpu_cmpxchg() and this_cpu_xchg support
  percpu,x86: relocate this_cpu_add_return() and friends
  connector: Use this_cpu operations
  xen: Use this_cpu_inc_return
  taskstats: Use this_cpu_ops
  random: Use this_cpu_inc_return
  fs: Use this_cpu_inc_return in buffer.c
  highmem: Use this_cpu_xx_return() operations
  vmstat: Use this_cpu_inc_return for vm statistics
  x86: Support for this_cpu_add, sub, dec, inc_return
  percpu: Generic support for this_cpu_add, sub, dec, inc_return
  ...

Fixed up conflicts: in arch/x86/kernel/{apic/nmi.c, apic/x2apic_uv_x.c, process.c}
as per Tejun.

* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
  usb: don't use flush_scheduled_work()
  speedtch: don't abuse struct delayed_work
  media/video: don't use flush_scheduled_work()
  media/video: explicitly flush request_module work
  ioc4: use static work_struct for ioc4_load_modules()
  init: don't call flush_scheduled_work() from do_initcalls()
  s390: don't use flush_scheduled_work()
  rtc: don't use flush_scheduled_work()
  mmc: update workqueue usages
  mfd: update workqueue usages
  dvb: don't use flush_scheduled_work()
  leds-wm8350: don't use flush_scheduled_work()
  mISDN: don't use flush_scheduled_work()
  macintosh/ams: don't use flush_scheduled_work()
  vmwgfx: don't use flush_scheduled_work()
  tpm: don't use flush_scheduled_work()
  sonypi: don't use flush_scheduled_work()
  hvsi: don't use flush_scheduled_work()
  xen: don't use flush_scheduled_work()
  gdrom: don't use flush_scheduled_work()
  ...

Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.